2000 Lexus ES300 oil

ENGINE
402
CHECKING THE ENGINE OILLEVEL
62E009
With the engine at operating temperature and turned
off, check the oil level on the dipstick.
1. To get a true reading, the vehicle should be on a level
spot. After turning off the engine, wait a few minutes for
the oil to drain back into the bottom of the engine.
2. Pull out the dipstick, and wipe it clean with a rag.
3. Reinsert the dipstick and push it in as far as it will go,
or the reading will not be correct.

ENGINE
403
62E002a

1Add oil 2O.K. 3Too full
4. Pull the dipstick out and look at the oil level on the end.
If it is between the low level mark ( 4 ) and the full level
mark ( 5 ), it is O.K.

ENGINE
405
If the oil level is below or only slightly above the low
mark, add engine oil of the same type as already in
the engine.
Remove the oil filler cap and add engine oil a little at a
time,
checking the dipstick. The approximate quantity of
oil needed to fill between the low level mark and the full
level mark on the dipstick is indicated below for
reference.
When the level reaches within the correct range, return
the filler cap and turn the cap clockwise until you hear a
click.
Oil quantity. L (qt., lmp. qt.) 1.5 (1.6, 1.3)
NOTICE
Avoid overfilling, or the engine could be
damaged. Ch eck the oil level on the dipstick once
again after adding the oil.

ENGINE
406
Engine oil selection
Use API SJ, ªEnergy±Conservingº multigrade engine oil
or ILSAC multigrade engine oil.
Recommended viscosity (SAE):
62L005±1
Temperature range anticipated before next oil change
SAE 5W±30 is the best choice for your vehicle, for
good fuel economy, and good starting in cold
weather.
If you use SAE 10W±30 engine oil in extremely low
temperatures, the engine may become difficult to
start, so SAE 5W±30 engine oil is recommended.

ENGINE
407
Oil identification marks
62L006±1

API Service Symbol
ILSAC Certification
Mark
Either or both API registered marks are added to some
oil containers to help you select the oil you should use.
 The API Service Symbol is located anywhere on the
outside of the container.
The top portion of the label shows the oil quality by
API (American Petroleum Institute) designation such
as SJ. The center portion of the label shows the SAE
viscosity grade such as SAE 5W±30.
ªEnergy±Conservingº, shown in the lower portion,
indicates that the oil has fuel±saving capabilities.
 The ILSAC (International Lubricant Standardization
and Approval Committee) Certification Mark is
displayed on the front of the container.
CHECKING THE ENGINE
COOLANT LEVEL

ELECTRICAL COMPONENTS
444
If electrolyte gets on your skin, thoroughly
wash the contacted area. If you feel a pain or
burn, get medical attention immediately.
 If electrolyte gets on your clothes, there is a
possibility of its soaking through to your skin,
so immediately take off the exposed clothing
and follow the procedure above, if necessary.
 If you accidentally swallow electrolyte, drink a
large quantity of water or milk. Follow with milk
of magnesia, beaten raw egg or vegetable oil.
Then go immediately for emergency help.Checking battery exterior
64E068

BODY
478

Dirt or sand adhered to the leather may damage
the treated surface and cause it to wear earlier.Remove dirt or sand using a vacuum cleaner.

If a stain should fail to come out with a neutraldetergent, apply a cleaner that does notcontain an organic solvent.

Never use organic substances such asbenzine, alcohol or gasoline, or alkaline or acid
solutions for cleaning the leather as these could cause discoloring.

Use of a nylon brush or synthetic fiber cloth,etc. may scratch the fine grained surface of the
leather.

Mildew may develop on soiled leather upholstery. Be especially careful to avoid oil
spots. Try to keep your upholstery alwaysclean.

Long exposure to direct sunlight may causethe leather surface to harden and shrink. Keepyour vehicle in a shaded area, especially in thesummer.

The interior of your vehicle is apt to heat up onhot summer days, so avoid placing on theupholstery items made of vinyl or plastic orcontaining wax as these tend to stick to leather
when warm.

Improper cleaning of the leather upholstery could result in discoloration or staining.
Synthetic Leather Areas (Dash)
The synthetic leather areas may be easily cleaned
with a mild soap or detergent and water.
First vacuum over the upholstery to remove loose dirt.
Then, using a sponge or soft cloth, apply the soap
solution to the synthetic leather. After allowing it to soak
in for a few minutes to loosen the dirt, remove the dirt and
wipe off the soap with a clean damp cloth. If all the dirt
does not come off, repeat the procedure. Commercial
foaming±type cleaners are also available which work
well. Follow the manufacturer's instructions.
NOTICE
Do not use solvent, thinner, gasoline or windowcleaner on the interior.
Carpets, Windows and Seat Belts
Begin by vacuuming thoroughly to remove as much dirt
as possible. Several types of foam cleaners are
available; some are in aerosol cans and others are
powders or liquids which you mix with water to produce
a foam. To shampoo the carpets, use a sponge or brush
to apply the foam. Rub in overlapping circles. Do not
apply water ± the best results are obtained by keeping
the carpet as dry as possible. Read the shampoo
instructions and follow them closely.
The seat belts may be cleaned with mild soap and

GAS STATION INFORMATION

Fuel selection:
Select Octane Rating 87 (Research Octane Number
91) or higher. For improved vehicle performance, the
use of premium unleaded gasoline with an Octane
Rating 91 ( Research Octane Number 96) or higher is
recommended.

Fuel tank capacity:
70 L (18.5 gal., 15.4 lmp. gal.)

Engine oil:
API SJ, ªEnergy±Conservingº multigrade engine oil
or ILSAC multigrade engine oil.
Recommended oil viscosity ± SAE 5W±30 if normal
temperatures are below 38 C (100F)
Oil capacity: L (qt., lmp.qt.)
Drain and refill with filter 4.7 (5.0, 4.1)
without filter 4.5 (4.8, 4.0)
See page 402 for detailed information.

Engine coolant:
Capacity: 8.8 L (9.3 qt., 7.7 lmp. qt.)
Coolant type ± ªTOYOTA Long Life Coolantº or
equivalent
With ethylene±glycol type coolant for a proper
corrosion protection of aluminum components
Do not use alcohol type antifreeze or plain water alone.
For checking the engine coolant, see page 407
.

Automatic transaxle:
Fluid type ± Automatic transmission fluid Type T±IV

Tire information:
See page 423 through 432 for detailed information.

Tire pressure:
Tire size: P205/65R15 92V or P215/60R16 91V
cold tires
kPa (kgf/cm
2 or bar, psi)
Vehicle loaded
up Vehicle load up to vehicle
capacity to 4 occupants weight
Front tires 180 (1.8, 26) 220 (2.2, . . . . . . . . . . . .
32)
Rear tires 180 (1.8, 26) 220 (2.2, . . . . . . . . . . .
32)
When driving under the above vehicle load conditions at
sustained high speeds above 160 km/h (100 mph), in
countries where such speeds are permitted by law,
inflate the front and rear tires 220 kPa (2.2 kgf/cm
2 or bar,
32 psi), but never exceed the maximum cold tire
pressure molded on the tire sidewall.