2000 Lexus ES300 stop start

STARTING AND DRIVING
291
(e) Backing up
31E010

1Brake pedal 2ªRº (Reverse) position
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with your foot, shift
the selector lever to the ªRº position.
NOTICE
Never shift into reverse while the vehicle ismoving.

STARTING AND DRIVING
292
(f) Parking
31E011±1

1Brake pedal 2Parking brake pedal
3ªPº (Park) position
1. Bring the vehicle to a complete stop.
2. Depress the parking brake fully to securely apply the
parking brake.
3. With the brake pedal held down with your foot, shift
the selector lever to the ªPº position.
CAUTION
Never attempt to move the selector lever into ªPº under
any circumstances while the vehicle is moving. Serious
mechanical damage and loss of vehicle control may
result.

STARTING AND DRIVING
293
(g) Good driving practice
If the transmission repeatedly shifts up and down
between the third and overdrive gears when climbing
a gentle slope, the overdrive should be turned off. Be
sure to turn the switch on immediately after climbing
the slope.
 When towing a trailer, in order to maintain efficient
engine braking and electrical charging performance,
do not use overdrive.
CAUTION
Always keep your foot on the brake pedal while stopped
with the engine running. This prevents the vehicle from
creeping.
NOTICE
Do not hold the vehicle on an upgrade with the accelerator pedal. This can cause thetransmission to overheat. Always use the brakepedal or parking brake.
(h) Rocking your vehicle if stuck
CAUTION
If your vehicle becomes stuck in snow, mud, sand, etc.,
then you may attempt to rock the vehicle free by moving
it forward and backward. Do not attempt this procedure
if people or objects are anywhere near the vehicle.
During the rocking operation the vehicle may suddenly
move forward or backward as it becomes un±stuck,
causing injury or damage to nearby people or objects.

STARTING AND DRIVING
306
BRAKE SYSTEM
The tandem master cylinder brake system is a hydraulic
system with two separate sub±systems. If either
sub±system should fail, the other will still work.
However, the pedal will be harder to press, and your
stopping distance will be longer. Also, the brake system
warning light may come on.
CAUTION
Do not drive your vehicle with only a single brake
system. Have your brakes fixed immediately.
Brake booster
The brake booster uses engine vacuum to power±assist
the brakes. If the engine should quit while you are
driving, you can bring the vehicle to a stop with normal
pedal pressure. There is enough reserved vacuum for
one or two stops but no more!

STARTING AND DRIVING
307
CAUTION
Do not pump the brake pedal if the engine stalls.
Each push on the pedal uses up your reserved
vacuum.
 Even if the power assist is completely lost, the brakes
will still work. But you will have to push the pedal
hard, much harder than normal. And your braking
distance will be longer.
Anti±lock brake system
The anti±lock brake system is designed to help
prevent lock±up of the wheels during a sudden
braking or braking on slippery road surfaces. This
assists in providing stability and steering
performance of the vehicle under these
circumstances.
Effective way to press the ABS brake pedal: When the
anti±lock brake system function is in action, just hold the
brake pedal down more firmly. Especially, in a panic stop,
you need to keep it depressed more firmly, and do not pump
the brake. Pumping the brake pedal makes the stopping
distance longer.

STARTING AND DRIVING
308The anti±lock brake system becomes operative after the
vehicle has accelerated to a speed in excess of
approximately 10 km/h (6 mph). It stops operating when
the vehicle decelerates to a speed below approximately
5 km/h (3 mph).
Depressing the brake pedal on slippery road surfaces
such as on the manhole cover, the steel plate under the
construction, joints in the bridge, etc. on a rainy day
tends to activate the anti±lock brake system.
You may hear a click or motor sound in the engine
compartment for a few seconds when the engine is
started or just after the vehicle is started. This means
that the anti±lock brake system is in the self±check
mode, and does not indicate a malfunction.
When the anti±lock brake system is activated, the
following conditions may occur, however, do not
indicate a malfunction of the system:

You may hear the anti±lock brake system operating
and feel the brake pedal pulsating and the vibrations
of the vehicle body and steering wheel. You may also
hear the motor sound in the engine compartment
even after the vehicle is stopped.
 At the end of the anti±lock brake system activation,
the brake pedal may move a little to the forward.

STARTING AND DRIVING
310
Anti±lock brake system is not designed to shorten the
stopping distance: Always drive at the moderate speed
and maintain a safe distance from the vehicle in front of
you. Compared with vehicles not fitted with an
anti±lock brake system, your vehicle may require a
longer stopping distance in the following cases:
 Driving on rough, gravel or snow±covered roads.
 Driving with tire chains installed.
 Driving over the steps such as the joints on the road.
 Driving on roads where the road surface is pitted or
has other differences in surface height.
Install all 4 tires of specified size at designated
pressure: The anti±lock brake system detects vehicle
speeds using the speed sensors for respective wheels'
turning speeds. The use of tires other than specified
may fail to detect the accurate turning speed, resulting
in a longer stopping distance.

STARTING AND DRIVING
312
Drum±in±disc type parking brake system
Your vehicle has a drum±in±disc type parking brake
system. This type of brake system needs
bedding±down of the brake shoes periodically or
whenever the parking brake shoes and/or drums are
replaced.
Have your Lexus dealer perform the bedding±down.
Brake assist system
When you slam the brakes on, the brake assist
system judges as an emergency stop and provides
more powerful braking for a driver who cannot hold
down the brake pedal firmly.
When you slam the brakes on, more powerful braking
will be applied. At this time, you may hear a sound in the
engine compartment and feel the vibrations of the brake
pedal. This does not indicate a malfunction.
The brake assist system becomes operative after the
vehicle has accelerated to a speed in excess of
approximately 10 km/h (6 mph). It stops operating when
the vehicle decelerates to a speed below approximately
5 km/h (3 mph).
For an explanation of this system's warning light, see
ªABS warning lightº on page 65 and ªVehicle skid control
system warning lightsº on page 65.