2000 FORD RANGER clock

5. Remove the bulb retaining ring by
rotating it counterclockwise (when
viewed from the rear) to free it
from the bulb socket, and slide the
ring off the plastic base. Keep the
ring to retain the new bulb.
6. Without turning, remove the old
bulb by gently pulling it straight
back out of the lamp assembly.
To install the new bulb:
Handle a halogen headlamp bulb carefully and keep out of
children's reach. Grasp the bulb only by its plastic base and do
not touch the glass. The oil from your hand could cause the bulb to
break the next time the headlamps are operated.
1. With the flat side of the bulb's plastic base facing upward, insert the
glass end of the bulb into the lamp assembly. You may need to turn the
bulb left or right to align the grooves in the plastic base with the tabs in
the lamp assembly. When the grooves are aligned, push the bulb into the
lamp assembly until the plastic base contacts the rear of the lamp
assembly.
2. Install the bulb retaining ring over the plastic base until it contacts the
rear of the socket by rotating clockwise until you feel a ªstop.º
3. Install the electrical connector into the plastic base until it snaps,
locking it into position.
4. Turn the headlamps on and make sure they work properly. If the
headlamp was correctly aligned before you changed the bulb, you should
not need to align it again.
Maintenance and care
198

Replacing front side marker bulbs
1. Open the hood.
2. Remove two screws from the
lamp assembly.
3. Disengage lamp assembly (it has
a snap fit).
4. Disconnect the electrical
connector from the bulb by pulling
rearward.
5. Rotate bulb socket
counterclockwise about
1¤4turn and
remove from lamp assembly.
6. Carefully pull bulb straight out of
socket and push in the new bulb.
7. Insert the bulb into the parking
lamp assembly. When the grooves in
the plastic base are aligned, push
the bulb into the lamp assembly
until the plastic base contacts the rear of the lamp assembly and turn to
lock.
8. Connect the electrical connector into the rear of the plastic base until
it ªsnaps.º
9. Align the lamp studs with the plastic grommets on the vehicle and
push to snap in place.
10. Install two screws on lamp assembly.
Maintenance and care
199

Replacing tail lamp/turn/backup lamp bulbs
The tail lamp/turn/backup lamp
bulbs are located in the same
portion of the tail lamp assembly,
one just below the other. Follow the
same steps to replace either bulb:
1. Open the liftgate to expose the
lamp assemblies.
2. Remove the four screws and the
lamp assembly from vehicle.
3. Rotate bulb socket
counterclockwise turn and remove
from lamp assembly.
4. Carefully pull the bulb straight
out of the socket and push in the
new bulb.
5. Install the bulb socket in lamp
assembly by turning clockwise.
6. Install the lamp assembly and
secure with four screws.
Replacing foglamp bulbs
1. Remove the bulb socket from the
foglamp by turning
counterclockwise.
2. Disconnect the electrical
connector from the foglamp bulb.
3. Connect the electrical connector to the new foglamp bulb.
4. Install the bulb socket in the foglamp turning clockwise.
Maintenance and care
200

Replacing high-mount brakelamp and cargo lamp bulbs
The replacement of the high-mount brakelamp bulb and cargo lamp bulb
is basically the same. This procedure covers the high-mount brakelamp
bulb.
To remove the brakelamp assembly:
1. Remove the two screws and lamp
assembly from vehicle.
2. Remove the bulb socket from
lamp assembly by rotating it
counterclockwise.
3. Carefully pull bulb straight out of
socket and push in the new bulb.
To install the brakelamp assembly:
1. Install the bulb socket into the
lamp assembly by rotating
clockwise.
2. Install the lamp assembly on the vehicle and secure with two screws.
Replacing license plate lamp bulbs
The license plate bulbs are located
behind the rear bumper. To change
the license plate lamp bulbs:
1. Reach behind the rear bumper to
locate the bulb socket.
2. Twist the socket counterclockwise
and remove.
3. Pull out the old bulb from socket
and push in the new bulb.
4. Install the bulb socket in lamp
assembly by turning it clockwise.
Using the right bulbs
Replacement bulbs are specified in the chart below. Headlamp bulbs must
be marked with an authorized ªD.O.T.º for North America and an ªEº for
Europe to assure lamp performance, light brightness and pattern and safe
visibility. The correct bulbs will not damage the lamp assembly or void the
lamp assembly warranty and will provide quality bulb burn time.
Maintenance and care
201

Climate control (see Air
conditioning or Heating) ............19
Clock .............................29,36,42,51
Clutch
fluid ..........................................167
operation while driving ..........116
recommended shift speeds ....118
Console ........................................63
Coolant
checking and adding ..............168
refill capacities .................172,209
specifications ...................212,214
Cruise control
(see Speed control) ....................55
Customer Assistance ................137
Ford accessories
for your vehicle ......................225
Ford Extended
Service Plan ............................218
Getting assistance outside the
U.S. and Canada .....................224
Getting roadside assistance ...137
Getting the
service you need ....................218
Ordering additional
owner's literature ...................229
The Dispute
Settlement Board ...................221
Utilizing the Mediation/
Arbitration Program ...............224
Daytime running lamps
(see Lamps) ................................18
Dipstick
automatic
transmission fluid ...................173
engine oil .................................163
Doors
door ajar warning .....................12
lubricant specifications ..........212
Driveline universal
joint and slip yoke ....................177Driving under
special conditions ..............122,123
mud ..........................................122
sand .........................................122
snow and ice ...........................123
through water ..................122,124
Emergencies, roadside
jump-starting ..........................152
Emission control system ..........195
Engine .................................214,215
check engine/
service engine soon light ...........8
cleaning ...................................204
coolant .....................................168
idle speed control ...................178
lubrication
specifications ...................212,214
refill capacities ........................209
service points ............160,161,162
starting after a collision .........138
Engine block heater .................104
Engine oil ..................................163
checking and adding ..............163
dipstick ....................................163
filter, specifications .........165,209
recommendations ...................165
refill capacities ........................209
specifications ...................212,214
Exhaust fumes ..........................105
Fluid capacities .........................209
Foglamps .....................................18
Four-Wheel Drive vehicles ..12,119
control trac ...............................24
description ..............................119
driving off road .......................121
electronic shift ...................24,119
indicator light .........................119
preparing to drive your
vehicle .....................................110
Fuel ............................................186
calculating fuel economy .......192
cap ...........................................188
Index
232