2000 FORD RANGER transmission fluid

CHECKING AND ADDING POWER STEERING FLUID
Check the power steering fluid.
Refer to the Scheduled Maintenance
Guide for the service interval
schedules. If adding fluid is
necessary, use only MERCONtAT F.
1. Start the engine and let it run until it reaches normal operating
temperature (the engine coolant temperature gauge indicator will be
near the center of the normal area between H and C).
2. While the engine idles, turn the steering wheel left and right several
times.
3. Turn the engine off.
4. Check the fluid level on the dipstick. It should be between the arrows
in the FULL HOT range. Do not add fluid if the level is within this range.
5. If the fluid is low, add fluid in small amounts, continuously checking
the level until it reaches the FULL HOT range. Be sure to put the
dipstick back in the reservoir.
TRANSMISSION FLUID
Checking automatic transmission fluid
Refer to your Scheduled Maintenance Guide for scheduled intervals for
fluid checks and changes. Your transmission does not consume fluid.
However, the fluid level should be checked if the transmission is not
working properly, i.e., if the transmission slips or shifts slowly or if you
notice some sign of fluid leakage.
Automatic transmission fluid expands when warmed. To obtain an
accurate fluid check, drive the vehicle until it is at normal operating
temperature (approximately 30 km [20 miles]). If your vehicle has been
Maintenance and care
173

operated for an extended period at high speeds, in city traffic during hot
weather or pulling a trailer, the vehicle should be turned off for about 30
minutes to allow fluid to cool before checking.
1. Drive the vehicle 30 km (20 miles) or until it reaches normal operating
temperature.
2. Park the vehicle on a level surface and engage the parking brake.
3. With the parking brake engaged and your foot on the brake pedal,
start the engine and move the gearshift lever through all of the gear
ranges. Allow sufficient time for each gear to engage.
4. Latch the gearshift lever in P (Park) and leave the engine running.
5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If
necessary, refer toIdentifying components in the engine compartment
in this chapter for the location of the dipstick.
6. Install the dipstick making sure it is fully seated in the filler tube.
7. Remove the dipstick and inspect the fluid level. The fluid should be in
the designated area for normal operating temperature or ambient
temperature.
Low fluid level
Do not drive the vehicle if the fluid
level is at the bottom of the dipstick
and the ambient temperature is
above 10ÉC (50ÉF).
Correct fluid level
The transmission fluid should be checked at normal operating
temperature 66ÉC-77ÉC (150ÉF-170ÉF) on a level surface. The normal
operating temperature can be reached after approximately 30 km (20
miles) of driving.
You can check the fluid without driving if the ambient temperature is
above 10ÉC (50ÉF). However, if fluid is added at this time, an overfill
condition could result when the vehicle reaches normal operating
temperature.
The transmission fluid should be in
this range if at normal operating
temperature (66ÉC-77ÉC
[150ÉF-170ÉF]).
Maintenance and care
174

The transmission fluid should be in
this range if at ambient temperature
(10ÉC-35ÉC [50ÉF-95ÉF]).
High fluid level
Fluid levels above the safe range
may result in transmission failure.
An overfill condition of transmission
fluid may cause shift and/or
engagement concerns and/or
possible damage.
High fluid levels can be caused by an overheating condition.
Adjusting automatic transmission fluid levels
Before adding any fluid, make sure the correct type is used. The type of
fluid used is normally indicated on the dipstick and also in the
Lubricant specificationssection in theCapacities and specifications
chapter.
Use of a non-approved automatic transmission fluid may cause
internal transmission component damage.
If necessary, add fluid in 250 mL (1/2 pint) increments through the filler
tube until the level is correct.
If an overfill occurs, excess fluid
should be removed by a qualified
technician.
An overfill condition of
transmission fluid may cause
shift and/or engagement concerns and/or possible damage.
Maintenance and care
175

Checking and adding manual transmission fluid
1. Clean the filler plug.
2. Remove the filler plug and
inspect the fluid level.
3. Fluid level should be at bottom of
the opening.
4. Add enough fluid through the
filler opening so that the fluid level
is at the bottom of the opening.
5. Install and tighten the fill plug
securely.
Use only fluid that meets Ford specifications. Refer to theCapacities
and specificationschapter.
Maintenance and care
176

Fluid Ford Part
NameApplication Capacity
Transmission
fluid
1Motorcraft
MERCONtAT F5-speed manual 2.65L
(2.8 quarts)2
Motorcraft
MERCONtV
AT F4x2 vehicles with
automatic and 2.5L
I4 engine9.4L
(9.9 quarts)3
4x2 vehicles with
automatic and 3.0L
or 4.0L V6 engine9.5L
(10.0 quarts)3
4x4 vehicles with
automatic9.8L
(10.3 quarts)3
Engine
coolant4Premium Engine
Coolant2.5L I4 engine with
manual
transmission10.0L
(10.5 quarts)
2.5L I4 engine with
automatic
transmission9.7L
(10.2 quarts)
3.0L V6 engine with
manual
transmission14.3L
(15.1 quarts)
3.0L V6 engine with
automatic
transmission14.0L
(14.8 quarts)
4.0L V6 engine with
manual
transmission13.0L
(13.7 quarts)
4.0L V6 engine with
automatic
transmission12.5L
(13.2 quarts)
Fuel tank N/A Regular cab (Short
wheel base)62.4L
(16.5 gallons)
Regular cab (Long
wheel base)75.7L
(20.0 gallons)
SuperCab 73.8L
(19.5 gallons)
Transfer
Case FluidMotorcraft
MERCONtAT F4x4 Vehicles 1.2L
(1.25 quarts)
Capacities and specifications
210

Fluid Ford Part
NameApplication Capacity
Front axle
lubricantMotorcraft SAE
80W-90
Premium Rear
Axle Lubricant4x4 Vehicles 1.7L (3.6 pints)
Rear axle
lubricant
5Motorcraft SAE
80W-90
Premium Rear
Axle LubricantAll 2.4-2.5L
(5.0-5.3 pints)
Windshield
washer fluidUltra-Clear
Windshield
Washer
ConcentrateAll 2.6L
(2.75 quarts)
1Ensure the correct automatic transmission fluid is used. MERCONtand
MERCONtV are not interchangeable. DO NOT MIX MERCONtand
MERCONtV. Refer to the Scheduled Maintenance Guide to determine
the correct service interval.
2Service refill capacity is determined by filling the transmission to the
bottom of the filler hole with the vehicle on a level surface.
3Indicates only approximate dry-fill capacity. Some applications may
vary based on cooler size and if equipped with an in-tank cooler. The
amount of transmission fluid and fluid level should be set by the
indication on the dipstick's normal operating range.
4Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford
Extended Life Engine Coolant (orange in color). Refer toAdding engine
coolant, in the Maintenance and Care chapter.
5Traction-Lok axles use 2.2±2.4L (4.75±5.0 pints) of rear axle lubricant.
Add 118 ml (4 oz.) of Additive Friction Modifier C8AZ-19B546-A or
equivalent meeting Ford specification EST-M2C118±A for complete refill
of Traction-Lok axles.
Service refill capacities are determined by filling the rear axle 6 mm to
14 mm (1/4 inch to 9/16 inch) below the bottom of the filler hole.
Capacities and specifications
211

ItemFord part
name or
equivalentFord part
numberFord
specification
Transmission
/steering/parking
brake linkages
and pivots,
brake and clutch
pedal shaft,
clutch pilot
bearing and.
input shaft
spline (manual
transmission).Premium
Long-Life GreaseXG-1-C or
XG-1-KESA-M1C75-B
Power steering
fluid, transfer
case fluid (4X4)
and transmission
fluid (manual)Motorcraft
MERCONtAT FXT-2-QDX MERCONt
Automatic
transmission
(4R44E, 5R44E
and 5R55E)Motorcraft
MERCONtV
AT F
2
XT-5-QM
MERCONtV
Windshield
washer fluidUltra-clear
Windshield
Washer
ConcentrateC9AZ-19550-AC ESR-M17P5-A
1Add 118 ml (4 oz.) of Additive Friction Modifier C8AZ-19B546-A or
equivalent meeting Ford specification EST-M2C118±A for complete refill
of Traction-Lok axles.
2Ensure the correct automatic transmission fluid is used. Transmission
fluid requirements are indicated on the dipstick or on the dipstick
handle. MERCONtand MERCONtV are not interchangeable. DO NOT
mix MERCONtand MERCONtV. Refer to your Scheduled Maintenance
Guide to determine the correct service interval.
Capacities and specifications
213

Air bag supplemental
restraint system ..........................84
and child safety seats ..............85
description ................................84
disposal ......................................88
driver air bag ............................86
indicator light ......................10,87
operation ...................................86
passenger air bag .....................86
passenger
deactivation switch ..............25,88
Air cleaner filter .......................209
Air conditioning ..........................19
manual heating and air
conditioning system .................21
Ambulance packages ....................3
Antifreeze
(see Engine coolant) ................168
Anti-lock brake system
(see Brakes) .......................107,108
Anti-theft system
warning light .............................11
Audio system (see Radio) .........26
Automatic transmission ............111
driving an automatic
overdrive ..........................112,114
fluid, adding ............................173
fluid, checking ........................173
fluid, refill capacities ..............209
fluid, specification ..................214
Auxiliary power point .................25
Axle
lubricant specifications ...212,214
refill capacities ........................209
traction lok ..............................124
Battery .......................................178
acid, treating emergencies .....178
charging system
warning light .............................11
jumping a disabled battery ....152
maintenance-free ....................178
replacement, specifications ...209servicing ..................................178
voltage gauge ............................17
Belt minder .................................80
Brakes ........................................106
anti-lock .....................106,107,108
anti-lock brake system (ABS)
warning light ......................10,108
brake warning light ..................10
fluid, checking and adding ....166
fluid, refill capacities ..............209
fluid, specifications ..........212,214
lubricant specifications ...212,214
parking ....................................108
shift interlock ..........................111
Break-in period .............................2
Capacities for refilling fluids ....209
Cargo area shade ........................63
Cargo net .....................................63
Certification Label ....................217
Child safety restraints ................93
child safety belts ......................93
Child safety seats ........................94
attaching with tether straps ....99
in front seat ..............................96
in rear seat ................................96
tether anchorage hardware .....99
Cleaning your vehicle ...............203
engine compartment ..............204
exterior .............................204,207
exterior lamps .........................206
instrument panel ....................207
instrument panel lens ............207
interior .....................................207
mirrors .....................................208
plastic parts ............................206
safety belts ..............................207
washing ....................................203
waxing .....................................203
wheels ......................................204
windows ..................................208
wiper blades ............................206
Index
231