2000 FIAT MAREA AUTO

Marea-Marea Weekend Technical Data
2000 range (§) Steering
00.41
ENGINE TYPE
n^p| 16 v
IESi JTD
Make
Rack and pinion power assisted
Wh
: -<
eel
' o ©
steering wheel
3 2.9
Wh
: -<
eel
%
rack and pinion
travel
142±1.5 mm 137±1.5 mm
/
/
1. *-

^ Minimum turning circle m 10.7 11
# |
Steering angle
r
outer ^
wheel 31° ± 30'
# |
Steering angle
inner ^
wheel 38° ± 30'
Steering column
with two universal joints
Copyright by Fiat Auto 39

Marea- Marea Weekend
2000 range ©
Technical Data
Wheels
WHEEL ALIGNMENT
00.44
unladen vehicle (•)
camber (**)
caster (**)
front
suspension
toe-in
offset
front wheels
±3*
36' 24» ± 30'
10 57' ± 30'
-1 - 1 mm
camber (**)
U1
rear
suspension
toe-in (**)
thrust angle
rear wheels i
-0° 45' ± 30'
2 ± 2 mm
(**) Angles not adjustable
(•) With the tyres inflated to the correct pressure and the vehicle in running order with 5 litres of fuel (•) Angular values, which cannot be adjusted, used for the correct alignment of the vehicle
Copyright by Fiat Auto 41

Technical Data
Front suspension
Marea- Marea Weekend
2000 range @
00.44
Front suspension independent, Mac Pherson type with transverse lower track control arms secured to an
auxiliary crossmember. Offset coil springs and double acting, telescopic, hydraulic shock absorbers. Anti-
roll bar connected to the telescopic damper.
CLASSIFICATION OF SPRINGS ACCORDING TO VARIOUS VERSIONS AND ENGINE TYPES
VERSIONS
ENGINE TYPES
VERSIONS
Standard E C
Standard with ABS E C
With air conditioning D B
With air conditioning, ABS and all options D B
With air conditioning and ABS D B
Standard with automatic transmission D
Standard with automatic transmission and ABS D
With air conditioning and automatic transmission C
With air conditioning, ABS and all options C
With ABS (fitted as standard) B
With ABS (fitted as standard) and air condi­
tioning A
With ABS (fitted as standard), air conditioning
and all options A
SPECIFICATIONS OF VARIOUS SPRINGS
Coil springs A B C D E
Wire diameter mm 13.6±0.05 13.5±0.05 13.2±0.05 13.2±0.05
Number of effective coils 3.75
Coil direction Clockwise
Released spring height mm 449 448 434 425 413
Load under which spring height is .
173 mm am 432±17 417±17 397±16 353-383 336-364
The springs have been divided into two cate­
gories identifiable by a mark
yellow (*) for those with a height of >173 mm
under a load of:
green (*) for those with a height of <173 mm
under a load of:
432 daN 417 daN 397 daN 368 daN 350 daN
( ) Springs of the same type must be fitted
42 Print n° 506.763/23

Technical Data
Front suspension
00.44
ENGINE TYPE h|p>jrD
Dampers
Make Double acting, telescopic, hydraulic
Open (start of buffering) mm 508 ± 2.5 501 ± 2.5
Closed (iron against iron) mm 361 ± 2.5 354 ± 2.5
Stroke mm 147
Anti-roll bar
Anti-roll bar diameter mm 18
Marea- Marea Weekend
2000 range ©
Copyright by Fiat Auto 43

Marea- Marea Weekend Technical Data
2000 range (§) Electrical equipment: starting
00.55
STARTER MOTOR l^p| 20v I^P) JTD
Make Bosch
DW -12V -1,1 kW
Bosch
0 74.5-1.1/12
Bosch
0 78.5-2 KW/12
Voltage V 12
Nominal power kW 1.1 1.1 2
Rotation, pinion side clockwise
No. of poles 6 4 6
Winding windings in series permanent magnets
Engagement free wheel
Operation solenoid
End float of armature shaft mm 0.1-0.5 0.1-0.5 0.1-0.5
Data for bench test
Operating test (*):
current A
speed rpm
voltage V
torque developed daNm
-
360-380
1150
8.15
1.30
500
1950
7.30
1.30
Engagement test (*):
current A
voltage V
torque developed daNm
-680-700
4.9
3.11
1200
5.5
3.0
Idle test (*):
current A
voltage V
speed rpm
-
60-80
4.9
4040
70-80
11.5
5450-5750
Relay [ pull in Q -0.33-0.37 0.4
Winding
resistance (*) 1 hold in Q -1.13-1.27 1.7
Lubrication
Internal splines and
shaft bushes
VS+ SAE 10W
Enagement sleeve and intermediate
disc TUTELA MR3
(*) Data obtained at an ambient temperature of 20°C.
NOTE When overhauling it is not necessary to undercut the insulator between the commutator bars
Copyright by Fiat Auto 47

Technical Data
Electrical equipment: recharging
00.55
Bosch KCB1-14V-45/80A
Bosch KCB2-14V-50/90A
M. Marelli A127IR-14V-55/100A
M. Marelli A115IM-14V-55/105A
M. Marelli RTM 151 B
Marea- Marea Weekend
2000 range ©)
Alternator wiring diagram
Typical voltage regulator curves
M. Marelli RTM 151 A
Copyright by Fiat Auto 49

Technical Data Marea-Marea Weekend
Electrical equipment: electronic injection- ignition 2000 range ©)
00.55
INTEGRATED ELECTRONIC
INJECTION/IGNITION SYSTEM r^p) lev
Make I.A.W. M.P.I. WEBER - MARELLI
Firing order 1-3-4-2
INJECTION/IGNITION CONTROL UNIT
Make and versions with manual gearbox I.A.W. 4EF. B3
type versions with automatic transmission I.A.W. 4EF. L1
IGNITION COIL WITH 4 HIGH TENSION INTAKES
Make Champion
Type BAE 920 A
Ohmic resistance of primary winding at 20°C Q 0.580
Ohmic resistance of secondary winding at 20°C Q 9100
SPARK PLUGS
Make and type NGK BKR5EZ
CHAMPION RC10YCC
Thread on engine M14x1.25
Spark gap mm 0.8
TOP DEAD CENTRE AND RPM SENSOR
Make M. Marelli
Type CVM 02
Sensor winding resistance at 20°C Q 575-750
Distance (gap) between sensor and
crankshaft pulley tooth 0.5 + 1.5
ADVANCE ON ENGINE
With engine idling 700±50/min 4°
50 Print n° 506.763/23

Marea- Marea Weekend Technical Data
2000 range © Electrical equipment: electronic injection- ignition
00.55
INTEGRATED ELECTRONIC
INJECTION/IGNITION SYSTEM I^P) 20v
Make Bosch ME31F001
Firing order 1-2-4-5-3
IGNITION COIL (1 PER SPARK PLUG)
Make Bosch
Type 0.221.504.014
Ohmic resistance of primary winding at 20°C Q 0.,4
Ohmic resistance of secondary winding at 20°C Q 8500
TOP DEAD CENTRE AND RPM SENSOR
Make and type Bosch 0.281.002.102
Sensor winding resistance at 20°C Q 774 + 946
Distance (gap) between sensor and
crankshaft pulley tooth 0.8 H- 1.5
DETONATION SENSOR
Make Bosch
Type 0.261.231.095
SPARK PLUGS
Make and type CHAMPION RC8BYC
Thread on engine M 14x 1.25
Spark gap mm 0.8
Copyright by Fiat Auto 51