2000 Citroen C5 wheel

Downloaded from www.Manualslib.com manuals search engine 225
BRAKES
BRAKE SPECIFICATIONS
Braking system specifications
- Braking circuit at «X».
- Front brakes with ventilated discs.
- Rear brakes with non-ventilated discs.
- Handbrake lever controlling cables acting on the
front wheels.
- The compensator and main brake limiter functions
are assured by the ABS EBD system fitted as
standard at the factory on all versions.
NOTE : EBD = Electronic Brakeforce Distribution Braking circuit
B3FP12WD

Downloaded from www.Manualslib.com manuals search engine BRAKE SPECIFICATIONS
Braking circuit diagram
(a) Hydraulic circuit.
(b) Electrical circuit.
(1)Master cylinder in tandem.
(2) Braking servo.
(3) Brake caliper.
(4) Hub equipped with a bearing with an integral magnetic wheel
(48 pairs of poles).
(5) Wheel sensor.
(6) Brake fluid level sensor.
(7)Hydraulic block plus ECU.
(8) Stoplamp switch.
(9)Instrument panel.
(10) Diagnostic socket.
(11) Built-in systems interface (BSI).
B3GP02HP
BRAKES
226

Downloaded from www.Manualslib.com manuals search engine BRAKE SPECIFICATIONS
(7) Hydraulic block
Elements
Electronic ABS MK.6047way connector.
ECU7 ITT - A Alone on the hydraulic block.
BASR MK.60 Changing only the ECU is prohibited.
2 way black connector.
Front wheel The sensors are inductive-type.
5 ITT - A 96 332 952 80 Mounted on the pivot.
sensor
Non-adjustable airgap :0.2 à 1.5 mm.
Tightening torque : 0.8 ± 0.2 m.daN
2way black connector.
Rear wheel The sensors are inductive-type.
sensor96 332 954 80 Mounted on the brake caliper support.
Non-adjustable airgap :0.15 à 1.6 mm.
Tightening torque : 0.8 ± 0.2 m.daN
Hub
4 SNRHub equipped with a bearing with an integral
bearing magnetic wheel (48pairs of poles).
ABS MK.60
Hydraulic 96 371 711 80 Installed on the front LH wheelarch.
block7 TEVES
BASK MK.604adjustment channels.
96 371 712 80 Ref. SupplierPart No.
Observations
B3FP12XC
BRAKES
227

Downloaded from www.Manualslib.com manuals search engine B3FP12JD
HANDBRAKE (Adjustment)
Adjustment
- Remove the rear ashtray from the handbrake console.
- (1) Nut for adjusting the tension of the handbrake
cables.
- Raise and support the vehicle with the front wheels
hanging free.
- Check the correct routing of the brake cables under the
vehicle.
- Apply and release the handbrake 10 times.
- Set the handbrake to the 5th notch.
- Tighten the nut (1) until the front brakes are applied.
- Pull the handbrake lever vigorously4 to 5 times.
- Set the handbrake to the 5th notch.
- Check that the front brakes are applied.
- With the handbrake released, check that the wheels
can be turned freely by hand.
- Lower the vehicle.
- Refit the rear ashtray to the handbrake console.
229BRAKES

Downloaded from www.Manualslib.com manuals search engine B3FP13BCAB3FP13CC
BLEEDING AND FILLING THE BRAKING SYSTEM
Bleeding, filling (continued).
Filling the braking system.
WARNING : Use only those hydraulic fluids that are approved and recommended.
- Fill the brake fluid reservoir (1).
Bleeding the braking system.
WARNING: During the bleeding operation, take care to maintain the level of brake fluid in the reser-
voir and to top it up, using only brake fluid that is clean and clear.
Bleeding the primary circuit.
WARNING: The ABS should not be active during the bleeding operation.
- Front brake caliper: Bleed screw(5).
- Rear brake caliper: Bleed screw (6).
- Bleed each wheel cylinder, proceeding in the following order :
Front LH wheel.
Front RH wheel.
Rear LH wheel.
Rear RH wheel.BRAKES
231