2000 CHRYSLER VOYAGER sensor

The PCM determines the spark advance based on
the following:
± engine coolant temperature
± crankshaft position
± camshaft position
± intake air temperature
± manifold absolute pressure
± throttle position
Engine Warm-Up Mode -This is an open loop-
mode. The PCM adjusts injector pulse width and
controls injector synchronization by controlling the
fuel injectors' ground paths. The PCM adjusts igni-
tion timing and engine idle speed. The PCM adjusts
the idle speed by controlling the idle air control
motor and spark advance.
Cruise or Idle Mode -When the engine is at
normal operating temperature, this is a closed loop
mode.
Acceleration Mode -This is a closed loop mode.
The PCM recognizes an increase in throttle position
and a decrease in manifold vacuum as engine load
increases. In response, the PCM increases the in-
jector pulse width to meet the increased load. The
A/C compressor may be de-energized for a short
period of time.
Deceleration -This is a closed loop mode. The
PCM recognizes a decrease in throttle position and
an increase in manifold vacuum as engine load
decreases. In response, the PCM decreases the
injector pulse width to meet the decreased load.
Full injector shut off may be obtained during high
speed deceleration.
Wide Open Throttle Mode -This is an open
loop mode. The throttle position sensor notifies the
PCM of a wide open throttle condition. Once a wide
open throttle is sensed, the PCM de-energizes the
A/C compressor clutch relay for 15 seconds.
3.2.5 NON-MONITORED CIRCUITS
The PCM does not monitor the following circuits,
systems, and conditions even though they could
have malfunctions that result in driveability prob-
lems. A diagnostic code may not be displayed for the
following conditions. However, problems with these
systems may cause a diagnostic code to be displayed
for other systems. For example, a fuel pressure
problem will not register a diagnostic code directly,
but could cause a rich or lean condition. This could
cause an oxygen sensor, fuel system, or misfire
monitor trouble code to be stored in the PCM.
Engine Timing -The PCM cannot detect an
incorrectly indexed timing chain, camshaft
sprocket, or crankshaft sprocket. The PCM also
cannot detect an incorrectly indexed distributor.(*)
Fuel Pressure -Fuel pressure is controlled by
the fuel pressure regulator. The PCM cannot detecta clogged fuel pump inlet filter, clogged in-line filter,
or a pinched fuel supply.(*)
Fuel Injectors -The PCM cannot detect if a fuel
injector is clogged, the pintle is sticking, or the
wrong injectors are installed.(*)
Fuel Requirements -Poor quality gasoline can
cause problems such as hard starting, stalling, and
stumble. Use of methanol-gasoline blends may re-
sult in starting and driveability problems. See indi-
vidual symptoms and their definitions in Section
6.0 (Glossary of Terms)
PCM Grounds -The PCM cannot detect a poor
system ground. However, a diagnostic trouble code
may be stored in the PCM as a result of this
condition.
Throttle Body Air Flow -The PCM cannot
detect a clogged or restricted air cleaner inlet or
filter element.(*)
Exhaust System -The PCM cannot detect a
plugged, restricted, or leaking exhaust system.(*)
Cylinder Compression -The PCM cannot de-
tect uneven, low, or high engine cylinder compres-
sion.(*)
Excessive Oil Consumption -Although the
PCM monitors the exhaust stream oxygen content
through the oxygen sensor when the system is in a
closed loop, it cannot determine excessive oil con-
sumption.
(*)NOTE: ANY OF THESE CONDITIONS
COULD RESULT IN A RICH OR LEAN
CONDITION CAUSING AN OXYGEN SENSOR
TROUBLE CODE TO BE STORED IN THE
PCM, OR THE VEHICLE MAY EXHIBIT ONE
OR MORE OF THE DRIVEABILITY
SYMPTOMS LISTED IN THE TABLE OF
CONTENTS.
3.2.6 SKIS OVERVIEW
The Sentry Key Immobilizer System (SKIS) is an
immobilizer system design to prevent unauthorized
vehicle operation. The system consists of a Sentry
Key Immobilizer Module (SKIM), ignition key(s)
equipped with a transponder chip and engine con-
troller. When the ignition switch is turned on, the
SKIM interrogates the ignition key. If the ignition
key is ``Valid'', the SKIM sends a CCD Bus message
to the engine controller indicating the presence of a
valid igntion key. Upon receiving a ``Valid'' key
signal the PCM will allow the engine to continue to
operate.
3.2.7 SKIM ON-BOARD DIAGNOSTICS
The SKIM has been programmed to transmit and
monitor many different coded messages as well as
CCD Bus messages. This monitoring is called ``On
Board Diagnosis''.
5
GENERAL INFORMATION
ProCarManuals.com

Certain criteria must be met for a diagnostic
trouble code to be entered into the SKIM memeory.
The criteria may be a range of; Input voltage, CCD
Bus message, or coded messages to the SKIM. If all
of the criteria for monitoring a circuit or function
are met and a fault is sensed, a diagnostic trouble
code will be stored in the SKIM memory.
3.2.8 SKIS OPERATION
When ignition power is supplied to the SKIM, the
SKIM performs an internal self-test. After the self-
test is completed, the SKIM neergizes the antenna
(this activates the transponder chop responds to the
challenge by generating an encrypted response
message using the following:
Secret Key -This is an electronically stored
value (identification number) that is unique to each
SKIS. The secret key is stored in the SKIM, PCM
and all ignition key tranponders.
Challenge -This is a random numbr that is
generated by the SKIM at each ignition key cycle.
The secret key and challenge are plugged into an
algorithm that produces the encrypted response
message. The transponder uses the crypto algo-
rithm to receive, decode and respond to the message
sent by the SKIM. After responding to the coded
message, the transponder sends a transponder ID
message to the SKIM. The SKIM compares the
transponder ID to the available valid key codes in
the SKIM memory (8 key maximum). After validat-
ing the key the SKIM sends a CCD Bus message
called a ``Seed Request'' to the engine controller
then waits for a PCM response. If the PCM does not
respond, the SKIM will send the seed request agian.
After three failed attempts the SKIM will stop
sending the seed request and store a trouble code. If
the PCM sends a seed response, the SKIM sends a
valid/invalid key message to the PCM. This is an
encrypted message that is generated using the
following:
VIN -Vehicle Identification Number
Seed -This is a random number that is generated
by the PCM at each ignition key cycle.
The VIN and seed are plugged into a rolling code
algorithm that encrypts the ``valid/invalid key'' mes-
sage. The PCM uses the rolling code algorithm to
receive, decode and respond to the valid/invalid key
message sent by the SKIM. After sending the valid/
invalid key massage the SKIM waits 3.5 seconds for
a PCM status message from the PCM. If the PCM
does not respond with a valid key message to the
SKIM, a fault is detected and a trouble code is
stored.
The SKIS incorporates a warning lamp (``ALARM
SET'') located in the message center. The lamp
receives switched ignition voltage and is hardwired
to the body control module. The lamp is actuated
when the SKIM sends a CCD Bus message to thebody controller requesting the lamp on. The body
controller then provides the ground for the lamp.
The SKIM will request lamp operation for the
following:
- bulb checks at ignition on
- to alert the vehicle operator to a SKIS malfunc-
tion
For all faults except transponder faults and VIN
mismatch, the lamp remains on steady. In the event
of a tranponder fault the light flashes at a rate of 1
Hz (once per second). If a fault is pesent the lamp
will emain on or flashing for the complete ignition
cycle. If a fault is stored in SKIM memory which
prevents the system form operating properly, the
PCM will allow the engine to start and run (for 2
seconds) up to six times. After the sixth attempt, the
PCM disables the starter relay until the fault is
corrected.
3.2.9 PROGRAMMING THE POWERTRAIN
CONTROL MODULE
Important Note:Before replacing the PCM for a
failed driver, control circuit or ground circuit, be
sure to check the related component/circuit integ-
rity for failures not detected due to a double fault in
the circuit. Most PCM driver/control circuit failures
are caused by internal failure to components (i.e.
12-volt pull-ups, drivers and ground sensors). These
failures are difficult to detect when a double fault
has occurred and only one DTC has set.
NOTE:IF THE PCM AND THE SKIM ARE
REPLACED AT THE SAME TIME, PROGRAM
THE VIN INTO THE PCM FIRST. ALL VEHICLE
KEYS WILL THEN NEED TO BE REPLACED
AND PROGRAMMED TO THE NEW SKIM.
The SKIS ``Secret Key'' is an ID code that is
unique to each SKIS. This code is programmed and
stored in the SKIM, engine controller and transpon-
der ship (ignition key). When replacing the PCM it
is necessary to program the secret key into the
PCM.
1. Turn the ignition on (transmission in park/
neutral).
2. Use the DRB and select ``THEFT ALARM'',
SKIM then MISCELLANEOUS''.
3. Select ``PCM REPLACED''.
4. Enter secured access mode by entering the vehi-
cle four-digit PIN.
6
GENERAL INFORMATION
ProCarManuals.com

to non-emission codes, they will seem like an intermit-
tent. These codes require a set of parameters to be
performed (The DRBIIItpre-test screens will help
with this for MONITOR codes), this is called a ªTRIPº.
All EURO STAGE III OBD DTCs will be set after one
or in some cases two trip failures, and the MIL will be
turned on. These codes require three successful (no
failures) TRIPS to extinguish the MIL, followed by 40
warm-up cycles to erase the code.
3.3.2 INTERMITTENT CODE
A diagnostic trouble code that is not there every
time the PCM checks the circuit is an ªintermittentº
code. Most intermittent codes are caused by wiring
or connector problems. Defects that come and go
like this are the most difficult to diagnose; they
must be looked for under specific conditions that
cause them. The following checks may assist you in
identifying a possible intermittent problem:
²Visually inspect related wire harness connectors.
Look for broken, bent, pushed out, or corroded
terminals.
²Visually inspect the related harnesses. Look for
chafed, pierced, or partially broken wire.
²Refer to any Hotline Newsletters or technical
service bulletins that may apply.
²Use the DRBIIItdata recorder or co-pilot.
²Use the DRBIIItPEP module lab scope.
3.3.3 RESET COUNTER
The reset counter counts the number of times the
vehicle has been started since codes were last set,
erased, or the battery was disconnected. The reset
counter will count up to 255 start counts.
The number of starts helps determine when the
trouble code actually happened. This is recorded by
the PCM and can be viewed on the DRBIIItas
STARTS since set.
When there are no trouble codes stored in mem-
ory, the DRBIIItwill display ªNO DTC'S Detectedº
and the reset counter will show ªSTARTS since
clear = XXX.º
3.3.4 HANDLING NO TROUBLE CODE
PROBLEMS
Symptom checks cannot be used properly unless
the driveability problem characteristic actually
happens while the vehicle is being tested.
Select the symptom that most accurately de-
scribes the vehicle's driveability problem and then
perform the test routine that pertains to this symp-
tom. Perform each routine test in sequence until the
problem is found. For definitions, see Section 6.0
Glossary of Terms.SYMPTOM DIAGNOSTIC TEST
HARD START CHECKING THE 5-VOLT
SUPPLY CIRCUIT
CHECKING SECONDARY
IGNITION SYSTEM
CHECKING ENGINE VAC-
UUM
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATION
CHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
CHECKING ENGINE ME-
CHANICAL SYSTEMS
CHECKING EVAP EMISSION
SYSTEM
CHECKING EGR SYSTEM
CHECKING IAT SENSOR
START AND
STALLCHECKING THE 5-VOLT
SUPPLY CIRCUIT
CHECKING SECONDARY
IGNITION SYSTEM
CHECKING PCM POWER
AND GND CKT
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATION
CHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
8
GENERAL INFORMATION
ProCarManuals.com

CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
HESITATION/
SAG/
STUMBLECHECKING THE 5-VOLT
SUPPLY CIRCUIT
CHECKING SECONDARY
IGNITION SYSTEM
CHECKING PCM POWER
AND GND CKT
CHECKING ENGINE VAC-
UUM
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATION
CHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
CHECKING FOR OXYGEN
SENSOR SWITCHING
CHECKING O2S HEATER
CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
CHECKING ENGINE ME-
CHANICAL SYSTEMS
CHECKING EVAP EMISSION
SYSTEM
CHECKING EGR SYSTEM
CHECKING IAT SENSOR
CHECKING PNP SWITCH
SURGE CHECKING THE 5-VOLT
SUPPLY CIRCUIT
CHECKING SECONDARY
IGNITION SYSTEM
CHECKING PCM POWER
AND GND CKT
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATIONCHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
CHECKING FOR OXYGEN
SENSOR SWITCHING
CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
CHECKING EVAP EMISSION
SYSTEM
LACK OF
POWER/
SLUGGISHCHECKING THE 5-VOLT
SUPPLY CIRCUIT
CHECKING SECONDARY
IGNITION SYSTEM
CHECKING PCM POWER
AND GND CKT
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATION
CHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
CHECKING FOR OXYGEN
SENSOR SWITCHING
CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
CHECKING EGR SYSTEM
SPARK
KNOCK/
DETONATIONCHECKING SECONDARY
IGNITION SYSTEM
CHECKING PCM POWER
AND GND CKT
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATION
9
GENERAL INFORMATION
ProCarManuals.com

CHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
CHECKING FOR OXYGEN
SENSOR SWITCHING
CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
CHECKING EVAP EMISSION
SYSTEM
CUTS OUT/
MISSESCHECKING SECONDARY
IGNITION SYSTEM
CHECKING PCM POWER
AND GND CKT
CHECKING THE FUEL
PRESSURE
CHECKING THE MINIMUM
IDLE AIR FLOW
CHECKING FOR OXYGEN
SENSOR SWITCHING
CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
CHECKING EGR SYSTEM
BACKFIRE/
POPBACKCHECKING SECONDARY
IGNITION SYSTEM
CHECKING PCM POWER
AND GND CKT
CHECKING THE FUEL
PRESSURE
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
CHECKING FOR OXYGEN
SENSOR SWITCHING
CHECKING EGR SYSTEM
RUNS
ROUGH/
UNSTABLE/
ERRATIC
IDLECHECKING SECONDARY
IGNITION SYSTEMCHECKING PCM POWER
AND GND CKT
CHECKING ENGINE VAC-
UUM
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATION
CHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
CHECKING FOR OXYGEN
SENSOR SWITCHING
CHECKING O2S HEATER
CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
CHECKING ENGINE ME-
CHANICAL SYSTEMS
CHECKING EVAP EMISSION
SYSTEM
CHECKING EGR SYSTEM
CHECKING IAT SENSOR
CHECKING PNP SWITCH
POOR FUEL
ECONOMYCHECKING SECONDARY
IGNITION SYSTEM
CHECKING PCM POWER
AND GND CKT
CHECKING ENGING VAC-
UUM
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATION
CHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
10
GENERAL INFORMATION
ProCarManuals.com

CHECKING FOR OXYGEN
SENSOR SWITCHING
CHECKING O2S HEATER
CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
CHECKING ENGINE ME-
CHANICAL SYSTEMS
CHECKING EVAP EMISSION
SYSTEM
CHECKING EGR SYSTEM
CHECKING IAT SENSOR
CHECKING PNP SWITCH
3.4 USING THE DRBIIIT
Refer to the DRBIIItuser 's guide for instructions
and assistance with reading trouble codes, erasing
trouble codes, and other DRBIIItfunctions.
3.5 DRB ERROR MESSAGES AND BLANK
SCREEN
Under normal operation, the DRBIIItwill dis-
play one of only two error messages:
± User-Requested WARM Boot or User-
Requested COLD Boot.
This is a sample of such an error message display:
ver: 2.14
date: 26 Jul93
file: key_itf.cc
date: Jul 26 1993
line: 548
err: 0x1
User-Requested COLD Boot
Press MORE to switch between this display
and the application screen.
Press F4 when done noting information.
3.5.1 DRB IIITDOES NOT POWER UP
If the LED's do not light or no sound is emitted at
start up, check for loose cable connections or a bad
cable. Check the vehicle battery voltage (data link
connector cavity 16). A minimum of 11 volts is
required to adequately power the DRBIIIt.
If all connections are proper between the
DRBIIItand vehicle or other devices, and the
vehicle battery is fully charged, an inoperative
DRBIIItmay be the result of a faulty cable or
vehicle wiring. For a blank screen, refer to the
appropriate body diagnostics manual.
3.5.2 DISPLAY IS NOT VISIBLE
Low temperatures will affect the visibility of the
display. Adjust the contrast to compensate for this
condition.
4.0 DISCLAIMERS, SAFETY,
WARNINGS
4.1 DISCLAIMERS
All information, illustrations, and specifications
contained in this manual are based on the latest
information available at the time of publication.
The right is reserved to make changes at any time
without notice.
4.2 SAFETY
4.2.1 TECHNICIAN SAFETY INFORMATION
WARNING: ENGINES PRODUCE CARBON
MONOXIDE THAT IS ODORLESS, CAUSES
SLOWER REACTION TIME, AND CAN LEAD
TO SERIOUS INJURY. WHEN THE ENGINE IS
OPERATING, KEEP SERVICE AREAS WELL
VENTILATED OR ATTACH THE VEHICLE
EXHAUST SYSTEM TO THE SHOP EXHAUST
REMOVAL SYSTEM.
Set the parking brake and block the wheels before
testing or repairing the vehicle. It is especially impor-
tant to block the wheels on front-wheel drive vehicles;
the parking brake does not hold the drive wheels.
When servicing a vehicle, always wear eye pro-
tection, and remove any metal jewelry such as
watchbands or bracelets that might make an inad-
vertent electrical contact.
When diagnosing a powertrain system problem,
it is important to follow approved procedures where
11
GENERAL INFORMATION
ProCarManuals.com

4.3.3 ELECTRONIC PINION FACTOR
WARNING
The pinion factor must be set for all new trans-
mission control modules. If the pinion factor is not
set or if it is set incorrectly, any speed-related
accessories will not operate or will operate inaccu-
rately. This includes the speedometer, speed con-
trol, rolling door locks, and other devices that are
operated by the powertrain and body control mod-
ules. For instructions on setting the pinion factor,
see the appropriate transmission diagnostic man-
ual or the service manual.
5.0 RECOMMENDED TOOLS
AND EQUIPMENT
DRBIIIt(diagnostic readout box) scan tool
fuel pressure adapter (C-6631) or #6539
fuel pressure kit (C-4799-B) or #5069
fuel release hose (C-4799-1)
MinAir flow fitting #6457
jumper wires
ohmmeter
oscilloscope
vacuum gauge
voltmeter
12 volt test light minimum 25 ohms resistance
with probe #8382
CAUTION: A 12 VOLT TEST LIGHT SHOULD
NOT BE USED FOR THE FOLLOWING
CIRCUITS, DAMAGE TO THE POWERTRAIN
CONTROLLER WILL OCCUR.
²5 Volt Supply
²8 Volt Supply
²J1850 PCI Bus
²CCD Bus
²CKP Sensor Signal
²CMP Sensor Signal
²Vehicle Speed Sensor Signal
²O2 Sensor Signal
6.0 GLOSSARY OF TERMS
ABSantilock brake system
backfire,
popbackfuel ignites in either the intake or
the exhaust system
CKPcrank position sensor
CMPcamshaft position sensor
cuts out,
missesa steady pulsation or the inability of
the engine to maintain a consistent
rpmDLCdata link connector (previously
called ªengine diagnostic connectorº)
detona-
tion,
spark
knocka mild to severe ping, especially un-
der loaded engine conditions
ECTengine coolant temperature sensor
EGRexhaust gas recirculation valve and
system
genera-
torpreviously called ªalternatorº
hard
startThe engine takes longer than usual
to start, even though it is able to
crank normally.
hesita-
tion, sag,
stumble
There is a momentary lack of response
when the throttle is opened.
This can
occur at all vehicle speeds. If it is se-
vere enough, the engine may stall.
IATintake air temperature sensor
IACidle air control valve
JTECCombined engine and transmission
control module
lack of
power,
sluggish
The engine has less than expected
power, with little or no increase in vehi-
cle speed when the throttle is opened.
LDPLeak Detection Pump
MAPmanifold absolute pressure sensor
MILmalfunction indicator lamp
MTVmanifold tuning valve
O2Soxygen sensor
PCIProgrammable Communication In-
terface
PCMpowertrain control module
PCMpowertrain control module
PCVpositive crankcase ventilation
PEPPeripheral Expansion Port
poor fuel
economyThere is significantly less fuel mile-
age than other vehicles of the same
design and configuration
rough,
unstable,
or er-
ratic idle
stallingThe engine runs unevenly at idle
and causes the engine to shake if it
is severe enough. The engine idle
rpm may vary (called ªhuntingº).
This condition may cause stalling if
it is severe enough.
SKIMSentry Key Immobilizer Module
SKISSentry Key Immobilizer System
start and
stallThe engine starts but immediately
dies.
13
GENERAL INFORMATION
ProCarManuals.com

surgeengine rpm fluctuation without cor-
responding change in throttle posi-
tion sensor
TPSthrottle position sensorTRStransmission range sensor
VSSvehicle speed sensor/signal
14
GENERAL INFORMATION
ProCarManuals.com