2000 CHRYSLER VOYAGER jump start

Symptom:
* NO CRANK CONDITION
POSSIBLE CAUSES
BATTERY CIRCUIT RESISTANCE TOO HIGH
FUSED B(+) CIRCUIT OPEN
STARTER RELAY CONTROL CIRCUIT OPEN
STARTER RELAY OUTPUT CIRCUIT OPEN
CRANKSHAFT NOT ABLE TO ROTATE
STARTER MOTOR DEFECTIVE
PCM DEFECTIVE (NO CRANK CONDITION)
STARTER RELAY DEFECTIVE (RESISTANCE <=100 OHMS)
STARTER RELAY DEFECTIVE (RESISTANCE ABOVE 100 OHMS)
IGNITION SWITCH OUTPUT CIRCUIT OPEN
PARK/NEUTRAL SWITCH DEFECTIVE
TEST ACTION APPLICABILITY
1Note: Ensure the SKIM has proper communication and that there are no
SKIM DTC's present before continuing.
Ignition Off.
Disconnect the Starter Relay Connector.
Note: Check connectors - Clean/repair as necessary.
Warning: The Transmission must be in Park and the Parking Brake must be
on for the next step.
Warning: The engine may be cranked in the next step. Keep away from
moving parts.
Briefly connect a jumper wire between Starter Relay Output and Fused B(+)
Circuits.
Did the Starter Motor crank the Engine?All
Ye s®Go To 2
No®Go To 9
2 Ignition Off.
Disconnect the Starter Relay Connector.
Note: Check connectors - Clean/repair as necessary.
With a Voltmeter, measure the Fused B(+) Circuit.
Is the voltage above 11.6 volts?All
Ye s®Go To 3
No®Repair open Fused B(+) Circuit. (check Ignition Switch Fuse in
PDC).
Perform Powertrain Verification Test VER-1A.
296
STARTING
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition Off.
Ensure the Transmission is in Park.
With the DRB, read the Park/Neutral Position Switch.
Does the Switch show Park?All
Ye s®Go To 4
No®Repair Park/Neutral Switch.
Perform Powertrain Verification Test VER-1A.
4 Ignition Off.
Disconnect the Starter Relay Connector.
Note: Check connectors - Clean/repair as necessary.
Using an ohmmeter, test the Starter Relay Terminals for resistance.
Is the resistance above 100 ohms?All
Ye s®Replace the Starter Relay.
Perform Powertrain Verification Test VER-1A.
No®Go To 5
5 Ignition Off
Disconnect the Starter Relay Connector.
Note: Check connectors - Clean/repair as necessary.
With a voltmeter, probe Ignition Switch Output Circuit.
While attempting to crank the engine, read the Voltmeter.
Is the voltage above 10 volts?All
Ye s®Go To 6
No®Repair the open Ignition Switch Output (Start) Circuit.
Perform Powertrain Verification Test VER-1A.
6 Ignition Off.
Disconnect the Starter Relay Connector.
Disconnect the Powertrain Control Module.
Note: Check connectors - Clean/repair as necessary.
With an ohmmeter, test the Starter Relay Control Circuit for resistance.
Is the resistance above 5.0 ohms?All
Ye s®Repair the open Starter Relay Control Circuit.
Perform Powertrain Verification Test VER-1A.
No®Go To 7
7 Ignition Off
Disconnect the Powertrain Control Module.
Note: Check connectors - Clean/repair as necessary.
Warning: The Transmission must be in park and the Parking Brake must be
on for the next step.
Warning: The Engine may be cranked in the next step. Keep away form
moving Engine parts.
Connect a jumper wire between the Starter Relay Control Circuit and ground.
Briefly turn the Ignition to the crank position and then release.
Did the Engine crank?All
yes
Go To 8
no
Replace the Starter Relay.
Perform Powertrain Verification Test VER-1A.
297
STARTING
* NO CRANK CONDITION ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
8 If there are no potential causes remaining, the Powertrain Control Module is
assumed to be defective.
View repair options.All
Repair
Replace the Powertrain Control Module.
Perform Powertrain Verification Test VER-1A.
9 Ignition Off.
Ensure the Transmission is in Park.
With the DRB, read the Park/Neutral Position Switch.
Does the Switch show Park?All
Ye s®Go To 10
No®Repair Park/Neutral Switch.
Perform Powertrain Verification Test VER-1A.
10 Ignition Off
Disconnect the Starter Relay Connector.
Note: Check connectors - Clean/repair as necessary.
Warning: The Engine may be cranked in the next step. Keep away from
moving parts.
Warning: The engine may be cranked in the next step. Keep away from
moving parts.
Briefly connect a jumper wire between Starter Relay Output and Fused B(+)
Circuits.
Did the Starter Solenoid click when the jumper wire was connected?All
Ye s®Go To 11
No®Go To 15
11 Ignition Off
Check the Battery Cables for high resistance. (Use Service Manual procedure.)
Did either Battery Circuit have a voltage drop greater than 0.2 volt?All
Ye s®Repair the Battery Circuit for high resistance.
Perform Powertrain Verification Test VER-1A.
No®Go To 12
12 Ignition Off
Attempt to manually rotate the Crankshaft 360 degrees.
Is the Crankshaft able to rotate 360 degrees?All
Ye s®Go To 13
No®Repair the Engine mechanical problem as necessary.
Perform Powertrain Verification Test VER-1A.
13 Ignition Off.
Disconnect the Starter Relay Connector.
Note: Check connectors - Clean/repair as necessary.
With a Voltmeter, measure the Fused B(+) Circuit.
Is the voltage above 11.6 volts?All
Ye s®Go To 14
No®Repair open Fused B(+) Circuit. (check Ignition Switch Fuse in
PDC).
Perform Powertrain Verification Test VER-1A.
298
STARTING
* NO CRANK CONDITION ÐContinued
ProCarManuals.com

CLOCKSPRING C3 - BLACK 2 WAYCAV CIRCUIT FUNCTION
1 X10 20RD/DB RADIO MUX
2 X20 20RD/BK RADIO CONTROL MUX
CLUTCH INTERLOCK SWITCH (MTX) - BLACK 2 WAYCAV CIRCUIT FUNCTION
1 F45 20YL/RD (RHD) IGNITION SWITCH OUTPUT (START)
1 F45 20YL (LHD) IGNITION SWITCH OUTPUT (START)
2 T141 20YL/RD IGNITION SWITCH OUTPUT (START)
CLUTCH INTERLOCK SWITCH JUMPER (EATX) - BLACK 2 WAYCAV CIRCUIT FUNCTION
1 T141 20YL/RD (RHD) IGNITION SWITCH OUTPUT (START)
1 T141 20YL (LHD) IGNITION SWITCH OUTPUT (START)
2 T141 20YL/RD (RHD) IGNITION SWITCH OUTPUT (START)
2 T141 20YL (LHD) IGNITION SWITCH OUTPUT (START)
CRANKSHAFT POSITION SENSOR - BLACK 3 WAYCAV CIRCUIT FUNCTION
1 K7 18OR 8V SUPPLY
2 K4 18BK/LB SENSOR GROUND
3 K24 18GY/BK CRANKSHAFT POSITION SENSOR SIGNAL
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
335
CONNECTOR PINOUTS
ProCarManuals.com