2000 CHRYSLER VOYAGER ABS

VERIFICATION TEST VER-3A APPLICABILITY
Charging System Verification
Use this test to verify that the Charging System symptom has been repaired and that the
vehicle can be returned to the customer.
Note: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and the Transponder (ignition key).
1. Inspect the vehicle to ensure that all components related to the repair are connected
properly.
2. With the DRBIIIt, Clear DTC's.
3. Perform generator output test. Refer to the appropriate service information as necessary.
4. Start the engine and set engine speed to 2000 RPM for at least thirty seconds.
5. Turn the ignition OFF.
6. Turn the ignition ON, with the engine not running.
7. With the DRBIIIt, Read the DTC's. If the DTC returns, or any other symptom or DTC is
present, refer to the symptom list for further diagnostic testing procedures. Check for any
Technical Service Bulletins that may apply.
8. If there are no DTC's present and all components are functioning properly, the repair is
complete.All
318
VERIFICATION TESTS
Verification Tests ÐContinued
ProCarManuals.com

VERIFICATION TEST VER-4A APPLICABILITY
Speed Control Verification
Use this test to verify that the Speed Control symptom has been repaired and that the vehicle
can be returned to the customer.
Note: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and the Transponder (ignition key).
1. Inspect the vehicle to ensure that all components related to the repair are connected
properly.
2. With the DRBIIIt, Clear DTC's.
3. Road test the vehicle at a speed above 35 MPH.
4. Turn the Speed Control ON.
5. Press and release the Set switch. Verify that the speed control engages.
6. With the Speed Control engaged:
A. Press and hold the ACCEL switch. Verify that the speed increases.
B. Press and hold the SET (or DECEL) switch. Verify that the vehicle speed decreases.
C. Press and release the CANCEL switch. Verify that the Speed Control disengages.
D. Allow the vehicle speed to drop below 25 MPH. Press and release the RESUME switch.
Verify that the previously set vehicle speed is attained.
E. Using caution, press and release the brake pedal. Verify that the Speed Control
disengages.
F. Increase vehicle speed by at least 10 MPH. Press and release the SET switch. Verify the
Speed Control maintains this speed.
G. Press and release the ON/OFF switch (turn the Speed Control OFF.) Verify that the Speed
Control disengages.
If any or all of these functions are not operating properly, refer to the symptom list for the
appropriate diagnostic testing procedures.
7. With the DRBIIIt, Read DTC's. If the DTC returns, or any other symptom or DTC is present,
refer to the symptom list for further diagnostic testing procedures. Check for any Technical
Service Bulletins that may apply.
8. If there are no DTC's present and all components are functioning properly, the repair is
complete.All
319
VERIFICATION TESTS
Verification Tests ÐContinued
ProCarManuals.com

VERIFICATION TEST VER-5A APPLICABILITY
OBDII Road Test Verification
Use this test to verify that the OBDII symptom has been repaired and that the vehicle can be
returned to the customer. The proper way to verify that an OBDII DTC has been repaired is to
allow the PCM to run and pass the appropriate OBDII monitor(s).
Note: If the Powertrain Control Module has been changed and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and the Transponder (ignition key).
1. Inspect the vehicle to ensure that all components related to the repair are connected
properly.
2. If any other DTC is present, refer to the symptom list for further diagnostic testing
procedures.
3. With the DRBIIIt, Clear DTC's.
4. In order for an OBDII monitor to run, certain pre-test conditions must be met. Refer to the
applicable OBDII monitor pre-test screen on the DRBIIItfor monitor enabling conditions.
5. Operate the vehicle within the enabling conditions and allow the applicable monitor to run.
While the monitor is running, the OBDII monitor screen on the DRBIIItwill display ªIN
PROGRESSº and the DRBIIItwill beep. After the monitor is complete, view the results. Refer
to the appropriate service information as necessary. A monitor may have to fail more than once
in order to set a DTC.
If the monitor fails, or the DTC returns, or any other symptom or DTC is present, refer to the
symptom list for further diagnostic testing procedures. Check for any Technical Service
Bulletins that may apply.
If there are no DTC's present and all components are functioning properly, the repair is
complete.ALL
Powertrain Verification Test VER-5A2 APPLICABILITY
Fuel System Lean/Rich or Misfire Verification
Use this test to verify that the Fuel System Lean, Fuel System Rich, or Misfire symptom has
been repaired and that the vehicle can be returned to the customer.
NOTE: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret KEY data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and the Transponder (ignition key).
1. Inspect the vehicle to ensure that all components related to the repair are connected
properly.
2. If any other DTC is present, refer to the symptom list for further diagnostic testing
procedures.
3. With the DRBIIIt, monitor the Similar Conditions Window and attempt to duplicate the
conditions that the vehicle was operating at when the DTC was set. If the conditions can be
duplicated, the Good Trip counter will change to one or more.
4. If the DTC resets, or the OBDII monitor fails after running, or if any other symptom or DTC
is present, return to the symptom list and perform the appropriate diagnostic testing
procedures. Check for any Technical Service Bulletins that may apply.
5. If the monitor runs and the Good Trip Counter changes to one or more, the condition is no
longer present. If there are no DTCs and all components are functioning properly, the repair is
complete.ALL
320
VERIFICATION TESTS
Verification Tests ÐContinued
ProCarManuals.com

Powertrain Verification Test VER-5A3 APPLICABILITY
OBDII Monitor Verification
Use this test to verify that the OBDII monitor symptom has been repaired and that the vehicle
can be returned to the customer.
NOTE: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and the Transponder (ignition key).
1. Inspect the vehicle to ensure that all components related to the repair are connected
properly.
2. If any other DTC is present, refer to the symptom list for further diagnostic testing
procedures.
3. With the DRBIIIt, monitor the pre-test enabling conditions. Operate the vehicle within the
enabling conditions and allow the applicable monitor to run.
4. If the DTC resets, or the OBDII monitor fails after running, or if any other symptom or DTC
is present, return to the symptom list and perform the appropriate diagnostic testing
procedurs. Refer to any Technical Service Bulletins that may apply.
5. If the monitor runs and the Good Trip Counter changes to one or more, the condition is no
longer present.
6. If there are no DTCs and all components are functioning properly, the repair is complete.All
Powertrain Verification Test VER-6A APPLICABILITY
LDP Monitor Verification
Use this test to verify that the LDP monitor symptom has been repaired and that the vehicle
can be returned to the customer.
NOTE: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and Transponder (ignition key).
1. Inspect the vehicle to ensure that all components are related to the repair are connected
properly.
2. If any other DTC is present, refer to the symptom list for futher diagnostic testing
procedures.
3. With the DRBIIIt, perform the LDP Monitor Test. Follow the instructions on the DRBIIIt
screen.
4. If the DTC resets, or the OBDII monitor fails after running, or if any other symptom or DTC
is present, return to the symptom list and perform the appropriate diagnostic testing
procedures. Refer to any Technical Service Bulletins that mat apply.
5. If the monitor runs and test does not fail, the condition is no longer present.
6. If there are no DTCs and all components are functioning properly, the repair is complete.All
321
VERIFICATION TESTS
Verification Tests ÐContinued
ProCarManuals.com

Powertrain Verification Test VER-7A APPLICABILITY
SKIS Verfication
Use this test to verify that SKIM system symptom has been repaired and that the vehicle can
be returned to the customer.
Note: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and SKIM
modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programmig information for the PCM, SKIM
and the Transponder (ignition key).
1.Inspect the vehicle to ensure that all components related to the repair are connected properly.
2. Inspect the engine oil for fuel contamination. Replace the oil and filter as necessary.
3. Start the engine.
4. Run the engine for one warm-up cycle to verify proper operation. With the DRBIIIt, confirm
that no DTCs are present and that all components are functioning properly. If the DTC is still
present refer to any Technical Service Bulletins that may apply.
5. If a different DTC(s) is present, refer to the symtom list and perform diagnostic testing as
necessary. If there are no DTCs present and all components are functioning correctly, repair is
now complete.All
322
VERIFICATION TESTS
Verification Tests ÐContinued
ProCarManuals.com

INTAKE AIR TEMPERATURE/MANIFOLD ABSOLUTE PRESSURE SENSOR (2.0L) - GRAY 4 WAYCAV CIRCUIT FUNCTION
A K4 18BK/LB SENSOR GROUND
B K21 18BK/RD INTAKE AIR TEMPERATURE SIGNAL
C K6 18VT/WT 5V SUPPLY
D K1 18DG/RD MAP SENSOR SIGNAL
INTAKE AIR TEMPERATURE SENSOR (2.4L) - GRAY 2 WAYCAV CIRCUIT FUNCTION
1 K4 18BK/LB SENSOR GROUND
2 K21 18BK/RD INTAKE AIR TEMPERATURE SIGNAL
KNOCK SENSOR - GRAY 2 WAYCAV CIRCUIT FUNCTION
1 K42 18DB/LG KNOCK SENSOR SIGNAL
2 K4 18BK/LB SENSOR GROUND
LEAK DETECTION PUMP - LT. GRAY 4 WAYCAV CIRCUIT FUNCTION
1- -
2 F87 18WT/BK FUSED IGNITION SWITCH OUTPUT (ST-RUN)
3 K106 18WT/DG LEAK DETECTION PUMP SOLENOID CONTROL
4 K107 18YL/BK LEAK DETECTION PUMP SWITCH SENSE
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
342
CONNECTOR PINOUTS
ProCarManuals.com

MANIFOLD ABSOLUTE PRESSURE SENSOR (2.4L/3.3L/3.8L) - BLACK 3 WAYCAV CIRCUIT FUNCTION
A K4 18BK/LB SENSOR GROUND
B K6 18VT/WT 5V SUPPLY
C K1 18DG/RD MAP SENSOR SIGNAL
OUTPUT SPEED SENSOR - GRAY 2 WAYCAV CIRCUIT FUNCTION
1 T13 18DB/BK SPEED SENSOR GROUND
2 T14 18LG/WT OUTPUT SPEED SENSOR SIGNAL
OXYGEN SENSOR (SENSOR SIDE)CAV CIRCUIT FUNCTION
1 - GROUND
2 - AUTOMATIC SHUT DOWN RELAY OUTPUT
3 - OXYGEN SENSOR GROUND
4 - OXYGEN SENSOR SIGNAL
OXYGEN SENSOR 1/1 UPSTREAM - GRAY 4 WAYCAV CIRCUIT FUNCTION
1 Z1 18BK GROUND
2 A142 18DG/OR AUTOMATIC SHUT DOWN RELAY OUTPUT
3 K127 18BK/OR OXYGEN SENSOR GROUND
4 K41 18BK/DG OXYGEN SENSOR 1/1 SIGNAL
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
343
CONNECTOR PINOUTS
ProCarManuals.com

POWERTRAIN CONTROL MODULE C1 - BLACK 40 WAYCAV CIRCUIT FUNCTION
1- -
2 K18 18RD/YL IGNITION COIL NO. 3 DRIVER
3 K17 18DB/TN IGNITION COIL NO. 2 DRIVER
4- -
5 V32 18YL/RD SPEED CONTROL ON/OFF SWITCH SENSE
6 A142 18DG/OR AUTOMATIC SHUT DOWN RELAY OUTPUT
7 K13 18YL/WT FUEL INJECTOR NO. 3 DRIVER
8 K20 18DG GENERATOR FIELD DRIVER (+)
9- -
10 Z12 18BK/TN GROUND
11 K19 18GY/RD IGNITION COIL NO. 1 DRIVER
12 - -
13 K11 18WT/DB FUEL INJECTOR NO. 1 DRIVER
14 K58 18BR/DB FUEL INJECTOR NO. 6 DRIVER
15 K38 18GY FUEL INJECTOR NO. 5 DRIVER
16 K14 18LB/BR FUEL INJECTOR NO. 4 DRIVER
17 K12 18TN/WT FUEL INJECTOR NO. 2 DRIVER
18 - -
19 - -
20 F87 18WT/BK FUSED IGNITION SWITCH OUTPUT (ST-RUN)
21 - -
22 G3 18BK/PK SERVICE ENGINE SOON INDICATOR DRIVER
23 - -
24 - -
25 K42 18DB/LG KNOCK SENSOR SIGNAL
26 K2 18TN/BK ENGINE COOLANT TEMPERATURE SENSOR SIGNAL
27 K127 18BK/OR OXYGEN SENSOR GROUND
28 - -
29 - -
30 K41 18BK/DG OXYGEN SENSOR 1/1 SIGNAL
31 K90 18TN (EXCEPT 3.0L) SMART START RELAY CONTROL
32 K24 18GY/BK CRANKSHAFT POSITION SENSOR SIGNAL
33 K44 18TN/YL CAMSHAFT POSITION SENSOR SIGNAL
34 - -
35 K22 18OR/DB THROTTLE POSITION SENSOR SIGNAL
36 K1 18DG/RD MANIFOLD ABSOLUTE PRESSURE SENSOR SIGNAL
37 K21 18BK/RD (2.4L) INTAKE AIR TEMPERATURE SIGNAL
38 C103 18DG/LB (EXCEPT
3.0L)A/C SWITCH SIGNAL
39 - -
40 K35 18GY/YL EGR SOLENOID CONTROL
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
349
CONNECTOR PINOUTS
ProCarManuals.com