2000 CHRYSLER CARAVAN fuse

TEST NTC-10BCHECKING THE FUEL HEATER AND THE CRANKCASE VENT HEATER
Perform TEST NTC-10A Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST
NTC-10B. TURN IGNITION OFF.
REPLACE FUSE #16.
NO
TURN IGNITION ON IS THE FUSE OPEN? TEST COMPLETE.*
AND INSPECT FUSE
#16.
YES
CONNECT A JUMPER
REMOVE FUEL HEATER WIRE ACROSS FUEL
RELAY. HEATER RELAY
CAVITIES 30 & 87
(IN PDC). FIG. 1
REPLACE FUSE #6 NO REPLACE THE FUEL
IS THE FUSE OPEN? HEATER RELAY.*
TURN IGNITION ON.
YES
KEY OFF. REPLACE FUSE #16 AND
TURN IGNITION ON. NO REPLACE THE FUEL
DISCONNECT THE IS THE FUSE OPEN? HEATER.*
FUEL HEATER INSPECT FUSE #16.
HARNESS CONNECTOR.
YES
KEY OFF. REPLACE FUSE #16 AND
DISCONNECT THE TURN IGNITION ON. NO REPLACE THE
CRANKCASE VENT IS THE FUSE OPEN? CRANKCASE VENT
HEATER HARNESS INSPECT FUSE #16. HEATER.*
CONNECTOR.
YES
REPAIR THE FUEL
HEATER RELAY
OUTPUT CIRCUIT FOR
A SHORT TO
GROUND.*
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
351
ProCarManuals.com

TEST NTC-11BCONTINUED - CHECKING RADIATOR FAN OPERATION
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST NTC-11B
CONTINUED FROM
THE PREVIOUS TURN IGNITION OFF.
PAGE.
TURN IGNITION ON. REPAIR THE OPEN
DISCONNECT RAD FAN USING A VOLTMETER, IS THE VOLTAGE NO FUSED BATTERY SUPPLY
RELAY #3.** MEASURE RELAY ABOVE 10.0 VOLTS? CKT. IF THE FUSE IS
HARNESS CONNECTOR BLOWN, CHECK FOR
CAVITY 8. FIG.1 SHORT TO GROUND.*
YES
CONNECT A JUMPER CAVITIES 2 AND 8.
WIRE ACROSS RAD IS THE RIGHT SIDE NO REPAIR OPEN RAD
FAN RELAY #3 RAD FAN ON? FAN RELAY #3
HARNESSOUTPUT CIRCUIT.*
CONNECTOR... FIG.1
YES
DISCONNECT RAD FAN RAD FAN RLY #1
RELAY #1 AND #3 HARNESS CONN. CAVITY IS THE RESISTANCE NO REPAIR OPEN HIGH
HARNESS CONNECTORS. 6 AND RAD FAN RLY #3 BELOW 5.0 OHMS? SPEED FAN CONTROL
MEASURE RESISTANCE HARNESS CONN. CAVITY CIRCUIT.*
BETWEEN... 6. FIG.1 AND 2
YES
MEASURE RESISTANCE RAD FAN RELAY #3
BETWEEN RAD FAN HARNESS CONNECTOR IS THE RESISTANCE NO REPAIR THE OPEN
RELAY #1 HARNESS CAVITY 4. BELOW 5.0 OHMS? DIESEL POWER RELAY
CONNECTOR CAVITY 4OUTPUT CIRCUIT.*
AND... FIG.1
YES
REPLACE THE RAD
FAN RELAY #3.*
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
359
ProCarManuals.com

TEST NTC-11CCHECKING RADIATOR FAN OPERATION
Perform TEST NTC-11A Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST
NTC-11C. TURN IGNITION OFF.
USING A VOLTMETER,
DISCONNECT THE RAD MEASURE RAD FAN IS THE VOLTAGE NO REPAIR OPEN
FAN RELAY #2.** RELAY #2 HARNESS ABOVE 11.0 VOLTS? BATTERY SUPPLY
CONNECTOR CAVITY 8. CIRCUIT OR FUSE.*
FIG.1
YES
CONNECT A JUMPER
WIRE ACROSS RAD CAVITIES 8 AND 2. DID THE FANS TURN YES REPLACE RAD FAN
FAN RELAY #2 ON? RELAY #2.*
HARNESS
CONNECTOR... FIG.1
NO
REPAIR RELAY #2
DID THE BATTERY YES OUTPUT CKT. FOR
SUPPLY FUSE BLOW? SHORT TO GROUND OR
SHORTED LEFT SIDE
RAD FAN MOTOR.*
NO
DISCONNECT FAN USE A VOLTMETER TO
MOTOR HARNESS MEASURE FAN MOTOR IS THE VOLTAGE NO REPAIR OPEN RELAY
CONNECTOR.** HARNESS CONNECTOR ABOVE 10.0 VOLTS? #2 OUTPUT
WITH JUMPER STILL CAVITY 4. CIRCUIT.*
CONNECTED... FIG.2
YES
RECONNECT FAN CONNECT A JUMPER REPAIR OPEN CKT
MOTOR HARNESS WIRE BETWEEN GROUND DID LEFT SIDE RAD NO BETWEEN RLY #1 AND
CONNECTOR. AND RAD FAN RELAY #1 FAN TURN ON? LEFT SIDE FAN MTR.*
DISCONNECT RAD FAN HARNESS CONNECTOR IF OK, REPLACE LEFT
RELAY #1.** CAVITY 8. FIG.3 SIDE FAN MTR.
YES
CONTINUE TEST
NTC-11C ON THE
NEXT PAGE.
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
361
ProCarManuals.com

TEST SC-3ACONTINUED - CHECKING SPEED CONTROL OPERATION
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
TEST SC-3A KEY OFF.
CONTINUED FROM
THE PREVIOUS DISCONNECT THE BRAKE
PAGE. LAMP SWITCH HARNESS
CONNECTOR.**
USING A VOLTMETER, REPAIR THE BRAKE
PROBE BRAKE LAMP IS THE VOLTAGE NO LAMP SWITCH FUSED
SWITCH HARNESS ABOVE 9.0 VOLTS? BATTERY SUPPLY
CONNECTOR CAVITY 6. CIRCUIT FOR AN
FIG.1 OPEN.*
YES
CONNECT A JUMPER DOES THE DRB
BETWEEN BRAKE LAMP DISPLAY CHANGE YES ADJUST OR REPLACE
SWITCH HARNESS TURN IGNITION ON. FROM "RELEASED" TO THE BRAKE LAMP
CONNECTOR CAVITIES "PRESSED"? SWITCH.*
5 AND 6. FIG.1
NO
REMOVE THE JUMPER. AT THE BRAKE LAMP REPAIR THE PRIMARY
USING A VOLTMETER, SWITCH HARNESS IS THE VOLTAGE NO BRAKE SWITCH
MEASURE THE CONNECTOR CAVITY 5. BELOW 1.0 VOLT? SIGNAL CIRCUIT FOR
PRIMARY SWITCH A SHORT TO
SIGNAL CIRCUIT... FIG.1 VOLTAGE.*
YES
KEY OFF. USING AN OHMMETER, REPAIR THE PRIMARY
MEASURE RESISTANCE IS THE RESISTANCE NO BRAKE SWITCH
DISCONNECT THE ECM OF THE PRIMARY BRAKE BELOW 5.0 OHMS? SIGNAL CIRCUIT FOR
HARNESS SW SIGNAL CKT. AN OPEN.*
CONNECTORS.** FIG.2
YES
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
381
ProCarManuals.com

TEST NS-1AREPAIRING A NO CRANK CONDITION
Perform TEST NS-SEL Before Proceeding
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
NOTE: BATTERY MUST
START TEST BE FULLY CHARGED
NS-1A. BEFORE DIAGNOSING
A NO-START
CONDITION.
NOTE: BEFORE VEHICLE THEFT DIAGNOSE
CONTINUING, BE (SKIM) SYSTEM FOR ARE ANY CODES YES TROUBLE CODE
SURE TO CHECK DIAGNOSTIC TROUBLE PRESENT? BEFORE
ENGINE SYSTEM CODES. CONTINUING.]
AND...
NO
INSPECT BATTERY
CABLES FOR IS THERE EVIDENCE YES REPAIR AS
TURN IGNITION OFF. CORROSION, OF PROBLEMS? NECESSARY.*
LOOSENESS OR OTHER
PROBLEMS.
NO
TURN IGNITION OFF. KEY ON. WITH A REPAIR THE STARTER
VOLTMETER, MEASURE IS THE VOLTAGE YES RELAY CONTROL
DISCONNECT THE ECM THE STARTER RELAY ABOVE 1.0 VOLT? CIRCUIT FOR A
HARNESS CONTROL CKT. SHORT TO VOLTAGE.*
CONNECTORS.** FIG.1
NO
KEY OFF. USING A FULLY DEPRESS THE
JUMPER WIRE CONNECT CLUTCH PEDAL. DID THE ENGINE YES REPLACE THE ENGINE
THE STARTER RELAY CRANK? CONTROL MODULE.*
CONTROL CKT TO ATTEMPT TO CRANK
GROUND. FIG.1 THE ENGINE.
NO
WITH A VOLTMETER,
DISCONNECT THE MEASURE THE FUSED IS THE VOLTAGE NO REPAIR OPEN FUSED
STARTER RELAY FROM B(+) CIRCUIT. ABOVE 11.6 VOLTS? BATTERY CIRCUIT.*
THE PDC.**
FIG.1
YES
WARNING: THE TRANS WARNING: THE ENGINE BRIEFLY CONNECT A
MUST BE IN NEUTRAL MAY BE CRANKED IN JUMPER WIRE BETWEEN CONTINUE TEST
AND THE PARKING THE NEXT STEP. KEEP THE STARTER RLY NS-1A ON THE
BRAKE MUST BE ON AWAY FROM MOVING OUTPUT AND FUSED NEXT PAGE.
FOR THE NEXT STEP. ENGINE PARTS. B(+) CKTS. FIG.1
N
O
S
T
A
R
T
T
E
S
T
S
395
ProCarManuals.com

TEST NS-2AREPAIRING A NO RESPONSE CONDITION
Perform TEST NS-SEL Before Proceeding
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
START TEST DOES THE VEHICLE YES PERFORM TEST
NS-2A. START? NS-2B.
NO
KEY OFF. WITH AN OHMMETER, IS THE RESISTANCE
MEASURE RESISTANCE ABOVE 5.0 OHMS FOR YES REPAIR THE OPEN
DISCONNECT THE ECM OF THE PCM GND CKTS ANY OF THE ECM GROUND.*
HARNESS AT HARNESS CAVITIES MEASUREMENTS?
CONNECTORS.** 1 AND 27. FIG.1
NO
KEY ON. USING A AT ECM HARNESS REPAIR OPEN OR
VOLTMETER, MEASURE CONNECTOR CAVITY 47. IS THE VOLTAGE NO SHORT TO GROUND IN
THE FUSED IGNITION ABOVE 10.0 VOLTS? THE FUSED IGNITION
SWITCH OUTPUT SWITCH OUTPUT
CIRCUIT... FIG.1 CIRCUIT.*
YES
KEY OFF. USING A VOLTMETER REPAIR OPEN FUSE
REMOVE THE DIESEL PROBE DIESEL POWER IS THE VOLTAGE NO OR FUSED BATTERY
POWER RELAY. RELAY CONNECTOR ABOVE 10.0 VOLTS? CIRCUIT TO DIESEL
CAVITY 30 (IN PDC). POWER RELAY.*
KEY ON. FIG.2
YES
KEY OFF. CONNECT A MEASURE VOLTAGE AT IS THE VOLTAGE
JUMPER WIRE ACROSS ECM HARNESS ABOVE 10.0 VOLTS NO REPAIR OPEN DIESEL
RELAY CONNECTOR CONNECTOR CAVITIES FOR EACH POWER RELAY OUTPUT
CAVATIES 30 AND 87. 2 AND 28. MEASUREMENT? CIRCUIT(S).*
FIG. 1 AND 2
YES
KEY OFF. RECONNECT WITH JUMPER WIRE
THE ENGINE CONTROL STILL CONNECTED, DOES THE VEHICLE NO REPLACE THE ENGINE
MODULE HARNESS ATTEMPT TO START START? CONTROL MODULE.*
CONNECTORS. VEHICLE.
YES
CONTINUE TEST
NS-2A ON THE
NEXT PAGE.
N
O
R
E
S
P
O
N
S
E
T
E
S
T
401
ProCarManuals.com

8.0 MAINTENANCE AND SERVICE INFORMATION
Refer to the appropriate service manual for information about repair and replacement procedures
When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating.
The use of a fuse with a rating other than indicated may result in a dangerous electrical system
overload. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must
be corrected.
NOTE:If it is necessary to replace the body controller and the SKIM, perform the following steps
in order:
± program the new body controller
± program the new SKIM
± replace all ignition keys, program new ignition keys to new SKIM
NOTE:If it is necessary to replace the engine control module and the SKIM, perform the following
steps in order:
± program the new SKIM
± program the new engine control module
8.1 Programming the Engine Control Module
1. To program the VIN, connect the DRB and turn ignition on.
2. Select ªENGINEº from the main menu. The DRB will request the SKIS four-digit PIN.
3. Enter the PIN.
4. Select ªENTERº to update the VIN. The DRB will display the updated VIN.
5. If the engine is equipped with air conditioning, the ECM a/c function must be enabled.
± Using the DRB select ªENGINEº, ªMISCELLANEOUSº then ªENABLE/DISABLE A/Cº.
± Push 1 to enable A/C. DRB screen should display ªA/C Activatedº.
8.2 Programming the Body Control Module
The SKIS ªSecret Keyº is an I.D. code that is unique to each SKIM. This code is programmed and
stored in the SKIM, body controller and transponder chip (ignition keys). When replacing the BCM
it is necessary to program the secret key into the new BCM using the DRB. Perform the following
steps to program the secret key into the body controller.
1. Turn the ignition on (transmission in park/neutral).
2. Use the DRB and select ``THEFT ALARM'', ``SKIM'' then ``MISCELLANEOUS''.
3. Select ``GS DIESEL BCM REPLACED''.
4. SELECT ªENTERº to update BCM VIN.
5. Enter secured access mode by entering the vehicle four-digit PIN.
NOTE:If three attempts are made to enter secure access mode using an incorrect PIN, secured
access mode will be locked out for one hour. To exit this lockout mode, turn the ignition to the RUN
position for one hour then enter the correct PIN. (Ensure all accessories are turned off. Also
monitor the battery state and connect a battery charger if necessary).
6. Press ªENTERº to transfer the secret key (the SKIM will send the secret key to the BCM).
G
E
N
E
R
A
L
I
N
F
O
R
M
A
T
I
O
N
425
ProCarManuals.com