2000 CHEVROLET TRACKER instrument cluster

2-
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is
working properly
-- and what to do if you have a problem.
2
-2 Keys
2
-4 Door Locks
2
-6 Remote Keyless Entry System (If Equipped)
2
-9 Tailgate
2
-10 Theft
2
-11 New Vehicle ªBreak-Inº
2
-11 Ignition Positions
2
-13 Starting Your Engine
2
-14 Engine Coolant Heater (If Equipped)
2
-16 Automatic Transmission Operation
2
-20 Manual Transmission Operation
2
-22 Four-Wheel Drive (If Equipped)
2
-24 Parking Brake
2
-25 Shifting Into PARK (P) (Automatic
Transmission Only)
2
-27 Shifting Out of PARK (P) (Automatic
Transmission Only)
2
-28 Parking Your Vehicle
(Manual Transmission Models Only)2
-28 Parking Over Things That Burn
2
-29 Engine Exhaust
2
-29 Running Your Engine While You're Parked
(Automatic Transmission)
2
-30 Windows
2
-32 Turn Signal/Multifunction Lever
2
-38 Exterior Lamps
2
-40 Interior Lamps
2
-41 Mirrors
2
-43 Storage Compartments
2
-48 Ashtrays and Cigarette Lighter
2
-48 Sun Visors
2
-48 Accessory Power Outlet
2
-49 Convertible Top (If Equipped)
2
-56 The Instrument Panel -- Your
Information System
2
-58 Instrument Panel Cluster
2
-59 Warning Lights, Gages and Indicators

2-12
ON (C): This is the position that the switch returns to
after you start your engine and release the switch. The
switch stays in the ON position when the engine is
running. But even when the engine is not running, you
can use ON to operate your electrical power accessories
and to display some instrument panel cluster warning
and indicator lights.
START (D): This is the position that starts the engine.
When the engine starts, release the key. The ignition
switch will return to ON for normal driving.
When the engine is not running, ACC and ON allow you
to operate your electrical accessories, such as the radio.
A warning tone will sound if you open the driver's door
when the ignition is in ACC or LOCK and the key is in
the ignition.
CAUTION:
On manual transmission vehicles, turning the key
to LOCK will lock the steering column and result
in a loss of ability to steer the vehicle. This could
cause a collision. If you need to turn the engine
off while the vehicle is moving, turn the key only
to ACC. Don't push the key in while the vehicle
is moving.
NOTICE:
If your key seems stuck in LOCK and you can't
turn it, be sure you are using the correct key;
if so, is it all the way in? If it is, then turn the
steering wheel left and right while you turn the
key hard. But turn the key only with your hand.
Using a tool to force it could break the key or the
ignition switch. If none of this works, then your
vehicle needs service.

2-19 Overdrive Off Switch (If Equipped)
The overdrive off switch is located on the left side of the
shift lever. By operating the overdrive off switch, the
four
-speed automatic transmission (three-speed plus
overdrive) can be converted to a three
-speed automatic
transmission. While in the three
-speed mode, the
transmission will not shift into the overdrive position.To convert the transmission to the three
-speed
mode, push in the overdrive off switch and release it.
The switch will come out and the OD/OFF indicator
light on the instrument panel cluster will come on. The
Overdrive Off switch is for normal driving, however, it
also offers more power and lower fuel economy than
driving in the overdrive position. Here are some times
you might choose to drive with the overdrive off
switch engaged:

When driving on hilly, winding roads.

When going down a steep hill.
To return the transmission to the four
-speed mode,
push in the overdrive off switch again. The switch will
remain in and the OD/OFF indicator light will go off.
Disengaging the Overdrive Off switch is for normal
driving with the four
-speed automatic transaxle.
If you need more power for passing, and you're:

Going less than about 35 mph (55 km/h), push
your accelerator pedal about halfway down.

Going about 35 mph (55 km/h), push your
accelerator all the way down.
Please note that if the transfer case shift lever is in the
4L position, the four
-speed automatic transmission will
remain in the three
-speed mode.

2-20 Power Mode Selector Switch
A power mode selector
switch is included
with the four
-speed
automatic transmission.
When you need more power for climbing hills or
quicker acceleration, press the P (power) switch. The
POWER indicator light on the instrument panel cluster
will come on. For normal driving, press the N (normal)
switch. The POWER indicator light will go off.
Manual Transmission Operation
5-Speed
This is your shift pattern.
Here's how to operate
your transmission:
FIRST (1): Press the clutch pedal and shift into
FIRST (1). Then, slowly let up on the clutch pedal as
you press the accelerator pedal.
You can shift into FIRST (1) when you're going less
than 20 mph (32 km/h). If you've come to a complete
stop and it's hard to shift into FIRST (1), put the shift
lever in NEUTRAL and let up on the clutch. Press the
clutch pedal back down. Then shift into FIRST (1).

2-32
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes your:

Turn Signal and Lane Change Indicator

Headlamp High/Low Beam Changer

Flash
-to-Pass
Turn Signal and Lane Change Indicator
The turn signal has an upward (for right) and a
downward (for left) position. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
When the turn is finished, the lever will return automatically.
An arrow on the instrument
panel cluster will flash in
the direction of the turn or
lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release it.
As you signal a turn or a lane change, if the arrows don't
flash but just stay on, a signal bulb may be burned out
and other drivers won't see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don't go on at all when you
signal a turn, check the fuse (see ªFuses and Circuit
Breakersº in the Index) and for burned
-out bulbs.

2-33 Headlamp High/Low Beam Changer
First, you must have the headlamps on. For high beams,
push the turn signal lever toward the instrument panel.
When the high beams are
on, a light on the instrument
panel cluster also will be on.
It will go off when you
switch to low beam.
To switch back to low beams, pull the lever toward you.
Flash-to-Pass
With the lever in the low-beam position, pull the lever
toward you to momentarily switch to high beam (to
signal that you are going to pass). When you release the
lever, the headlamps will return to low
-beam operation.
Windshield Wipers
The lever on the right side of the steering column
controls the windshield wipers and washers.
You control the windshield wipers by moving the stalk
up or down.
For steady wiping at low speed, move the stalk down
to LO. For higher speed wiping, move the stalk down
further to HI. To stop the wiper, move the stalk to OFF.

2-57
A. Side Defroster Vent
B. Air Vent
C. Turn Signal/Multifunction Lever
D. Instrument Panel Cluster
E. Windshield Wiper/Washer Lever
F. Hazard Switch
G. Rear Window Defogger (If Equipped)
H. Comfort Controls
I. Vent Shut
-off Thumbwheel
J. Audio System
K. AshtrayL. Shift Lever
M. Power Mode Switch (If Equipped)
N. Cigarette Lighter
O. Ignition Switch
P. Instrument Panel Fuse Block
Q. Hood Release
R. Instrument Panel Brightness Control
S. Power Remote Control Mirror (If Equipped)
T. Cruise Control Button (If Equipped)
U. Coinholder
V. Rear Window Wiper/Washer (If Equipped)

2-58
Instrument Panel Cluster
Your instrument cluster is designed to let you know at a glance how your vehicle is running. You'll know how
fast you're going, about how much fuel you have left, and many other things you'll need to know to drive safely
and economically.
U.S. Cluster shown; Canada similar