2000 CHEVROLET MONTE CARLO light

2-11
Theft
Vehicle theft is big business, especially in some cities.
Although your vehicle has a number of theft
-deterrent
features, we know that nothing we put on it can make
it impossible to steal. However, there are ways you
can help.
Key in the Ignition
If you leave your vehicle with the keys inside, it's an
easy target for joy riders or professional thieves
-- so
don't do it.
When you park your vehicle and open the driver's door,
you'll hear a chime reminding you to remove your key
from the ignition and take it with you. Always do this.
Your ignition and transaxle will be locked.
And remember to lock the doors.
Parking at Night
Park in a lighted spot, close all windows and lock your
vehicle. Remember to keep your valuables out of sight.
Put them in a storage area, or take them with you.
Parking Lots
If you park in a lot where someone will be watching
your vehicle, it's best to lock it up and take your keys.
But what if you have to leave your ignition key?

If possible, park in a busy, well lit area.

Put your valuables in a storage area, like your
trunk or glove box. Be sure to close and lock the
storage area.

Close all windows.

Lock the glove box.

Lock all the doors except the driver's.

Then take the door key and remote keyless entry
transmitter with you.

2-12
Content Theft-Deterrent
(If Equipped)
Your vehicle may be equipped with a content
theft
-deterrent alarm system.
With this system, a light on the radio will flash.
This light reminds you to activate the theft
-deterrent
system. Here's how to do it:
1. Open the door.
2. Lock the door with the power door lock switch or the
remote keyless entry transmitter. The light on the
radio should come on and stay on. If using the
remote keyless entry transmitter (if equipped), the
door does not need to be open.
3. Close all doors. The light on the radio will slowly
flash once the system is armed.
Once armed, the alarm will go off if someone tries to
enter the vehicle (without using the remote keyless entry
transmitter or a key) or turns the ignition on with an
incorrect key. The horn will sound and your vehicle's
headlamps and back
-up lamps will flash for
approximately two minutes.When the alarm is armed, the trunk may be opened with
the remote keyless entry transmitter. If you use the key
to open the trunk, the alarm will sound. Also, the power
door lock switches are disabled. You must use your
remote keyless entry transmitter or your key to unlock
the doors when the system is armed.
Arming with the Power Lock Switch
Your alarm system will arm when you use either power
lock switch to lock the doors while any door or the trunk
is open and the key is removed from the ignition.
The light on the radio flashes quickly to let you know
when the system is ready to arm with the power door
lock switches. The light on the radio will stop flashing
and stay on when you press the bottom of the power
lock switch, to let you know the system is arming. After
all doors and the trunk are closed and locked, the light
on the radio will flash slowly to let you know the system
is armed.

2-13 Arming with the Remote Keyless
Entry Transmitter
Your alarm system will arm when you use your remote
keyless entry transmitter (if equipped) to lock the doors,
if the key is not in the ignition. The light on the radio
will turn on to let you know the system is arming. After
all doors and the trunk are closed and locked, the light
on the radio will begin flashing at a very slow rate to let
you know the system is armed.
Disarming with the Remote Keyless
Entry Transmitter
Your alarm system will disarm when you use your
remote keyless entry transmitter (if equipped) to unlock
the doors. The light on the radio will go off to let you
know the system is no longer armed.
The first time a remote UNLOCK command is
received, three flashes will be seen and three horn chirps
heard to indicate an alarm condition has occurred since
last arming.
Disarming with Your Key
Your alarm system will disarm when you use your key
to unlock the doors. The light on the radio will go off to
let you know the system is no longer armed.
Vehicle Customization Settings
Some of your vehicle's convenience features can be
reset or customized to perform according to your
preference. The features you can program depend upon
the options that came with your vehicle. The following
list shows the features that can be reset or customized
along with the option you need to program that feature:

Settings (Available for All)

Oil Life Reset (Available for All)

Low Tire Pressure Reset (If Equipped)

Delayed Headlamp Illumination (Available for All)

Automatic Door Lock and Unlock
(Available for All)

Remote Visual Verification (Available with Remote
Keyless Entry)

Remote Audible Verification (Available with Remote
Keyless Entry)

Content Theft Operation (If Equipped with Content
Theft System)

Trunk Jamb (If Equipped with Content
Theft System)

2-14

Horn Chirp On Timer (Available with Remote
Keyless Entry)

Remote Keyless Entry Transmitter Programming
(Available with Remote Keyless Entry)

Return to Original Factory Settings
(Available for All)

Exit Vehicle Customization Mode
To reset or customize your vehicle's features, you must
first enter the vehicle customization main menu. To
enter the main menu:
1. Turn the ignition to ACC or ON and the radio off.
2. Press and hold the DISP button on the radio for at
least five seconds until SETTINGS is displayed.
3. Press the SEEK up or down arrows to scroll through
each available feature on your main menu.
4. Press the PREV or NEXT buttons to scroll through
the lower menu. An asterisk will appear next to the
item that is the current setting.The following information shows how to reset or
customize features after entering the main menu:
SETTINGS
- Display Current Settings
OIL LIFE
- Oil Life Reset: This feature allows you to
reset the engine oil life monitor after an oil change, see
ªEngine Oilº in the Index. Be careful not to reset the
OIL LIFE accidentally at any time other than when the
oil has been changed. It can't be reset accurately until
the next oil change. To clear the CHANGE ENGINE
OIL light from the instrument cluster and reset the oil
life monitor:
1. Scroll, using the SEEK up or down arrows, until OIL
LIFE appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. RESET will then be displayed.
3. Press the DISP button to reset. A chime will be heard
to verify the new setting and DONE will be
displayed for one second.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-15
TIRE MON (Tire Inflation Monitor Reset): This feature
allows you to reset the tire pressure monitor after
checking all tire pressures, see ªTiresº in the Index.
To clear the LOW TIRE PRESSURE light from the
instrument cluster and reset the tire inflation monitor:
1. Scroll, using the SEEK up or down arrows, until
TIRE MON appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. RESET will be displayed.
3. Press the DISP button to reset. A chime will be heard
to verify the new setting and DONE will be
displayed for one second.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.LT DELAY (Delayed Headlamp Illumination):
This feature allows the vehicle's headlamps and
parking lamps to stay on for a fixed amount of time
after you exit the vehicle. To customize delayed
headlamp illumination:
1. Scroll, using the SEEK up or down arrows, until
LT DELAY appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. The current selection will have an asterisk
next to it. Scroll, using the PREV or NEXT buttons,
through the following options:

OFF
- Turns feature off.

30 SEC
- 30 seconds.

60 SEC
- 60 seconds.
3. With your preference displayed, press the DISP
button to select. A chime will be heard to verify the
new setting. The new selection will be displayed
with an asterisk for one second.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-16
AUTOLOCK (Automatic Door Lock and Unlock): With
the ignition in ON and the vehicle's doors closed, this
feature allows the vehicle doors to automatically lock
and unlock when the driver shifts the vehicle's transaxle
into and out of PARK (P). To customize the automatic
door lock and unlock:
1. Scroll, using the SEEK up or down arrows, until
AUTOLOCK appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. The current selection will have an asterisk
next to it. Scroll through the following options:

OFF
- Turns feature off.

LCK ONLY
- Automatic door lock on/automatic
door unlock off.

DRVR UNL
- Automatic door lock on/automatic
door unlock on (driver's door only).

ALL UNL
- Automatic door lock on/automatic
door unlock on.
3. With your preference displayed, press the DISP
button to select. A chime will be heard to verify the
new setting. The new selection will be displayed
with an asterisk for one second.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.FOB LIGHT (Remote Visual Verification): This feature
allows the exterior lights to flash when the remote
keyless entry transmitter is used to lock or unlock the
vehicle. To customize remote visual verification:
1. Scroll, using the SEEK up or down arrows, until
FOB LIGHT appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. The current selection will have an asterisk
next to it. Scroll through the following options:

OFF
- Turns feature off.

ON
- One flash for each remote lock/two flashes
for each remote unlock.
3. With your preference displayed, press the DISP
button to select. A chime will be heard to verify the
new setting. A new selection will be displayed with
an asterisk for one second.
If your vehicle is equipped with the content
theft
-deterrent system, the first time a remote UNLOCK
command is received, three flashes will be seen and
three horn chirps heard to indicate an alarm condition
has occurred since last arming. See ªContent
Theft
-Deterrent Systemº in the Index.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-20
Passlock

Your vehicle is equipped with the Passlock
theft
-deterrent system.
Passlock is a passive theft
-deterrent system. Passlock
enables fuel if the ignition lock cylinder is turned with a
valid key. If a correct key is not used or the ignition lock
cylinder is tampered with, fuel is disabled and the
engine will not start.
During normal operation, the SECURITY message
will be displayed after the key is turned to the ON
ignition position.
If the engine stalls and the SECURITY message flashes,
wait until the light stops flashing before trying to restart
the engine.
If the engine is running and the SECURITY message
comes on, you will be able to restart the engine if you turn
the engine off. However, your Passlock system is not
working properly and must be serviced by your dealer.
Your vehicle is not protected by Passlock at this time. You
may also want to check the fuse (see ªFuses and Circuit
Breakersº in the Index). See your dealer for service.
In an emergency, call the Chevrolet Roadside Assistance
Center at 1
-800-CHEV-USA
(1-800-243-8872).
(In Canada, call 1
-800-268-6800.)
New Vehicle ªBreak-Inº
NOTICE:
Your vehicle doesn't need an elaborate
ªbreak
-in.º But it will perform better in the
long run if you follow these guidelines:

Don't drive at any one speed -- fast or
slow
-- for the first 500 miles (805 km).
Don't make full
-throttle starts.

Avoid making hard stops for the first
200 miles (322 km) or so. During this time
your new brake linings aren't yet broken
in. Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking
-in guideline every
time you get new brake linings.

Don't tow a trailer during break
-in.
See ªTowing a Trailerº in the Index for
more information.

2-22
ON: This is the position to which the switch returns
after you start the engine and release the switch. The
switch stays in ON when the engine is running. But
even when the engine is not running, you can use ON
to operate your electrical power accessories and to
display some instrument panel cluster messages and
warning lights.
START: This position starts the engine. When the
engine starts, release the key. The ignition switch will
return to ON for normal driving.
When the engine is not running, ACC and ON allow you
to operate your electrical accessories, such as the radio.
A warning chime will sound if you open the driver's
door when the ignition is in OFF or ACC and the key is
in the ignition.Retained Accessory Power (RAP)
With retained accessory power (RAP), your power
windows, audio system and the optional sunroof will
continue to work up to 10 minutes after the ignition key
is turned to OFF and no door is opened.
Starting Your Engine
Move your shift lever to PARK (P) or NEUTRAL (N).
Your engine won't start in any other position
-- that's a
safety feature. To restart when you're already moving,
use NEUTRAL (N) only.
NOTICE:
Don't try to shift to PARK (P) if your vehicle is
moving. If you do, you could damage the
transaxle. Shift to PARK (P) only when your
vehicle is stopped.