2000 CADILLAC ESCALADE lock

5-20 Removing the Spare Tire and Tools
The equipment you'll need is located in the rear
cargo area. The spare tire is located under the rear of
the vehicle.
To open the jack cover, turn the wing nut
counterclockwise and take the cover off.
To take the jack out, turn the wing
-head bolt
counterclockwise and take it and the retainer off.
Take the jack and storage box out and take the tools
out of the box.
Your vehicle may have a pair of emergency gloves
secured to the jack. You can use them when changing
the tire, or during other emergency situations. Remember
to replace them with the jack, so you will have them if
needed later.
The spare tire is stored under the vehicle in an
underbody carrier.

5-21
A. Hoist Assembly
B. Hoist Shaft
C. Ratchet
D. Jack HandleE. Retainer
F. Valve Stem,
Pointed Down
G. Spare TireFollow these instructions to lower the spare tire:
1. One side of the ratchet has an UP marking. The
other side has a DOWN marking. Assemble the
ratchet to the hook near the end of the jack handle
(as illustrated) with the DOWN marking facing you.
Insert the other end through the hole in the rear
bumper and into the hoist shaft.
2. Turn the ratchet counterclockwise to lower the
spare tire to the ground. Continue to turn the
ratchet until the spare tire can be pulled out from
under the vehicle.
3. When the tire has been lowered, tilt the retainer at
the end of the cable so it can be pulled up through
the wheel opening.
4. Put the spare tire near the flat tire.

5-23
UP Marking DOWN Marking
One side of the ratchet has an UP marking. The other
side has a DOWN marking.
With the UP marking on the ratchet facing you, rotate
the ratchet clockwise. That will lift the jack head a little.

5-24
To access the lug nuts, place the wheel wrench in the
slot on the wheel and gently pry off the center piece to
remove it.
Removing the Flat Tire and Installing the
Spare Tire
1. Use the ratchet and wheel wrench to loosen all the
wheel nuts. Turn the wheel wrench counterclockwise,
with DOWN facing you, to loosen the wheel nuts.
Don't remove the wheel nuts yet.
2. If the flat tire is on the rear of the vehicle, put the
jack handle extension on the jack handle.

5-26
Front Position Rear Position
4. With UP on the ratchet facing you, raise the vehicle
by turning the ratchet and wheel wrench clockwise.
Raise the vehicle far enough off the ground so there
is enough room for the spare tire to fit.
5. Remove all the wheel
nuts and take off the
flat tire.
6. Remove any rust or dirt
from the wheel bolts,
mounting surfaces and
spare wheel.

5-28
Front Position Rear Position
8. Lower the vehicle by turning the ratchet and wheel
wrench counterclockwise. Lower the jack completely.
9. Tighten each wheel nut by turning the wheel
wrench clockwise.
10. Tighten the nuts
firmly in a crisscross
sequence as shown.
Turn the wheel
wrench clockwise.

5-29
CAUTION:
Incorrect wheel nuts or improperly tightened
wheel nuts can cause the wheel to become loose
and even come off. This could lead to an accident.
Be sure to use the correct wheel nuts. If you have
to replace them, be sure to get new GM original
equipment wheel nuts.
Stop somewhere as soon as you can and have
the nuts tightened with a torque wrench to
140 lb
-ft (190 N´m)
NOTICE:
Improperly tightened wheel nuts can lead to
brake pulsation and rotor damage. To avoid
expensive brake repairs, evenly tighten the wheel
nuts in the proper sequence and to the proper
torque specification.
Storing a Flat or Spare Tire and Tools
CAUTION:
Storing a jack, a tire or other equipment in the
passenger compartment of the vehicle could
cause injury. In a sudden stop or collision, loose
equipment could strike someone. Store all these
in the proper place.
Store the flat tire where the spare tire is stored.
Put the tools into the storage box and close it tightly. Fit
the storage box on the bracket with the bolt through the
box. Put the jack onto the box. Be sure the jack is stored
as shown in the following illustrations. The jack handle
attachment point is circled in the following illustrations
to show the direction the jack should face when it is
stored properly. Secure the emergency gloves, if your
vehicle has them, to the jack using the provided strap.
Slide the retainer over the bolt onto the jack and put the
wing nut on it. Turn the nut clockwise until it is tight
against the retainer.
Replace the jack storage cover by simply reversing the
removal procedure described earlier.

5-31
Spare Tire Storage
A. Hoist Assembly
B. Hoist Shaft
C. Ratchet
D. Jack HandleE. Retainer
F. Valve Stem,
Pointed Down
G. Spare TireFollow these instructions to restore a spare or flat tire:
1. Lay the tire on the ground at the rear of the vehicle.
Position the tire so that the valve stem is pointed
down and to the rear of the vehicle.
2. Tilt the retainer downward and through the wheel
opening. Make sure that the retainer is fully seated
across the underside of the wheel.
3. Attach the ratchet, with the UP mark facing you,
near the hook at the end of the jack handle. Insert
the other end, on an angle, through the hole in the
rear bumper and into the hoist shaft.
4. Raise the tire fully against the underside of the
vehicle. Continue turning the ratchet clockwise until
there are two ªclicksº or ªratchets.º The spare tire
hoist cannot be over
-tightened.
5. Grasp and push against the tire to be sure it is stored
securely and does not move.