2000 CADILLAC DEVILLE ignition

1-3 Four-Way Power Lumbar Control
(If Equipped)
If your vehicle has this
feature, the driver's and
passenger's seatback lumbar
support can be adjusted four
ways by moving the single
switch located on the side of
the seat.
To increase the lumbar support, push the switch forward.
To decrease the support, push the switch backward. To
adjust the location of the lumbar support, push the
switch upward or downward.
Keep in mind that as your seating position changes, as it
may during long trips, so should the position of your
lumbar support. Adjust the seat as needed.
If you have the optional personalization package, the
power lumbar control can be programmed for memory
recall. For more information, see ªMemory and
Personalization Featuresº in the Index.
Massaging Lumbar (If Equipped)
Push the top of the lumbar control where it is marked
AUTO briefly to activate the massage feature.
The massage cycle will run continuously for up to
10 minutes and can be interrupted by pushing the
lumbar control down briefly. The lumbar support can be
adjusted during the massage cycle by moving the switch
forward to increase support and rearward to decrease
support. The massage cycle will continue to run even if
the ignition is turned to OFF, unless interrupted.
Four-Way Rear Power Lumbar
(If Equipped)
Four-way lumbar, without the massage feature, is also
available for the outboard rear seating positions. To
activate the rear lumbar feature, push forward on the
switch located on the rear door trim to increase support
or rearward to decrease support. The lumbar switch can
also be moved up and down to adjust the location of
the support.

1-4 Adaptive Seat Control (Option)
The adaptive seat control is located on the outboard side
of each front seat. With the ignition in ON, first use the
power seat control to get the proper position.
Then press the top of the control where it is marked
AUTO. The system will inflate the cushion and take a
reading, then automatically deflate the cushion to a
suggested level of comfort, by distributing the
pressure evenly.
You may still wish to further adjust the overall firmness
or softness of the seat cushion. To get to your desired
level of comfort, hold the control up to increase the
firmness, or down for less firmness. When you let go of
the control, the seat will then automatically readjust to
your desired level of comfort.You will also need to adjust the lumbar support. To
increase the lumbar support, push forward on the control
and to decrease support, push rearward on the control.
(The lumbar will then automatically adjust to your
body's positioning for the duration of the trip in
two
-minute cycles.)
If you exit the vehicle after the system has been
activated and the seat is left unoccupied for more than
two minutes, the system will deflate. You will then need
to readjust the lumbar support upon returning to
your vehicle.
To turn off the adaptive seat feature while still in your
vehicle, press the control down briefly. The seat will
also deflate when the ignition is turned to OFF.

1-5 Memory Seat, Mirrors and Steering
Wheel (Option)
The controls for these
features are located on the
driver's door panel, and are
used to program and recall
previous settings.
Adjust the driver's seat (including the lumbar
adjustments), both the outside mirrors and steering
wheel to a comfortable position and then press the SET
button. Within five seconds, press button 1.
A second mirror, seating and steering wheel position can
be programmed by repeating the above steps and
pressing button 2. Each time a memory button is
pressed, a single beep will sound. Each time button 1 or
2 is pressed, the memory positions will be recalled. Two
personalized exit positions can be set by first recallingthe driving position (1 or 2), positioning the wheel and
seat in the desired exit positions and then pressing the
SET button and, within five seconds, pressing the EXIT
button. the exit position for either previously set driver
can be recalled by pressing the EXIT button.
If you use the remote keyless entry transmitter to enter
your vehicle, automatic seat and mirror movement will
occur. The numbers on the back of the transmitters,
1 and 2, correspond directly to the numbers on the
buttons on the door panel and each seat and mirror can
be programmed to suit driver 1 or 2.
When the key is placed in the ignition in the OFF
position or when the unlock button is pressed on the
transmitter, the seats and mirrors will automatically
adjust to the programmed position.
Programming for automatic mirror and/or seat
movement is done through the Driver Information
Center (DIC). You can choose to either select or not
select automatic seat and/or mirror movement using the
transmitter or by placing your key in the ignition. For
programming information, see ªMemory and
Personalization Featuresº in the Index.

1-6 Heated Seats (Option)
Your vehicle may be equipped with heated front and rear
seats. The control buttons are located on the armrests.
The HEAT/OFF button controls the temperature settings
HI, MED and LO. The other button is to choose BACK
ONLY heating. The LO setting warms the seatback and
cushion until the seat approximates body temperature.
The MED and HI settings heat the seatback and seat
cushion to a slightly higher temperature, and the BACK
ONLY heats only the seatback. The temperature can be
adjusted by pushing the button from HI to LO or, until
the desired setting is reached. You will be able to feelheat in approximately two minutes. To heat just the
seatback, push the BACK ONLY button once, after first
activating the heated seat feature. To turn off the heat in
the seatback, push the button again. The feature will
shut off when the ignition is turned to OFF.
Reclining Front Seatbacks
Press the recliner control (B), located on the side of the
seat, forward or rearward to adjust the seatback.
Push the recliner control (B) up or down to adjust the
safety belt tower.

1-32
NOTICE:
If you damage the covering for the driver's or the
right front passenger's air bag, or the air bag
covering on the driver's, right front passenger's
or rear seatback, the bag may not work properly.
You may have to replace the air bag module in
the steering wheel, both the air bag module and
the instrument panel for the right front
passenger's air bag, or both the air bag module
and seatback for the side impact air bag. Do not
open or break the air bag coverings.
Servicing Your Air Bag-Equipped Vehicle
Air bags affect how your vehicle should be serviced.
There are parts of the air bag systems in several places
around your vehicle. Your dealer and the service manual
have information about servicing your vehicle and the
air bag systems. To purchase a service manual, see
ªService and Owner Publicationsº in the Index.
CAUTION:
For up to 10 seconds after the ignition key is
turned off and the battery is disconnected, an air
bag can still inflate during improper service. You
can be injured if you are close to an air bag when
it inflates. Avoid yellow connectors. They are
probably part of the air bag systems. Be sure to
follow proper service procedures, and make sure
the person performing work for you is qualified
to do so.
The air bag systems do not need regular maintenance.

2-
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is
working properly
-- and what to do if you have a problem.
2
-2 Keys
2
-4 Door Locks
2
-7 Remote Keyless Entry System
2
-12 Trunk
2
-15 Theft
2
-16 Theft-Deterrent System
2
-18 PASS-Key
III
2
-20 New Vehicle ªBreak-Inº
2
-20 Ignition Positions
2
-22 Starting Your Engine
2
-24 Engine Coolant Heater (If Equipped)
2
-25 Automatic Transaxle Operation
2
-30 Parking Brake
2
-32 Shifting Into PARK (P)
2
-35 Shifting Out of PARK (P)
2
-36 Parking Over Things That Burn
2
-37 Engine Exhaust
2
-37 Running Your Engine While You're Parked
2
-38 Windows2
-39 Tilt Wheel and Telescopic Column
2
-40 Turn Signal/Multifunction Lever
2
-46 Exterior Lamps
2
-51 Interior Lamps
2
-53 Mirrors
2
-57 Storage Compartments
2
-60 Rear Power Sunshade (If Equipped)
2
-61 Cellular Telephone (Option)
2
-62 Sunroof (Option)
2
-63 HomeLink
Transmitter
2
-68 The Instrument Panel -- Your
Information System
2
-73 Warning Lights, Gages and Indicators
2
-87 Driver Information Center (DIC)
2
-102 Night Vision System (Option)
2
-106 Navigation (Option)
2
-107 Ultrasonic Rear Parking
Assist (URPA) (Option)

2-2
Keys
CAUTION:
Leaving children in a vehicle with the ignition
key is dangerous for many reasons. A child or
others could be badly injured or even killed.
They could operate the power windows or other
controls or even make the vehicle move. If they
turned the ignition to ON and moved the shift
lever out of PARK (P), that would release the
parking brake. Don't leave the keys in a vehicle
with children.

2-3
Master Key Valet Key
There is a master key that works all of the lock cylinders
(driver's door, trunk, ignition and glove box).
There is also a VALET key which only operates the
driver's door and the ignition.Both the master and VALET key have a transponder
embedded into the key for security and vehicle theft
deterrence. The keys also come with a bar code tag.
Keep the bar code tag in a safe place. If you lose your
key, you will be able to have a new one made using the
bar code tag. The replacement key must have a vehicle
theft deterrent system transponder embedded in it.
NOTICE:
Your vehicle has a number of new features that
can help prevent theft. You can have a lot of
trouble getting into your vehicle if you ever lock
your keys inside. You may even have to damage
your vehicle to get in. So be sure you have
extra keys.