2000 CADILLAC DEVILLE light

2-19
It is possible for the PASS-Key III decoder to learn the
transponder value of a new or replacement key. Up to
ten additional keys may be programmed for the vehicle.
This procedure is for learning additional keys only. If all
the currently programmed keys are lost or do not
operate, you must see your dealer or a locksmith who
can service PASS
-Key III to have keys made and
programmed to the system.
See your dealer or a locksmith who can service
PASS
-Key III to get a new blank key that is cut exactly
as a current black
-colored driver's key that operates the
system. Do not use a gray
-colored valet key for
this procedure.
To program the new key:

Insert the current driver's key (black in color) in the
ignition and start the engine. If the engine will not
start see your dealer for service.

After the engine has started, turn the key to OFF, and
remove the key.
Insert the key to be programmed and turn it to ON
within ten seconds of removing the previous key.

The SECURITY light will turn off once the key has
been programmed. It may not be apparent that the
SECURITY light went on due to how quickly the
key is programmed.

Repeat the Steps 1 through 4 if additional keys are to
be programmed.
If you are ever driving and the SECURITY light comes
on and stays on, you will be able to start your engine if
you turn it off. Your PASS-Key III system, however, is
not working properly and must be serviced by your
dealer. Your vehicle is not protected by the PASS
-Key
III system at this time.
If you lose or damage a PASS
-Key III key, see your
dealer or a locksmith who can service PASS
-Key III to
have a new key made.

2-30
Parking Brake
Hold the regular brake
pedal down with your right
foot and push the parking
brake pedal down with
your left foot to set the
parking brake.
If the ignition is on, the BRAKE indicator light
should come on. If it doesn't, you need to have your
vehicle serviced.
When you move out of PARK (P) or NEUTRAL (N)
and the engine is running, the parking brake should
release. If the parking brake has not been fully released
and you try to drive off with the parking brake on, the
BRAKE indicator light will come on and stay on.If the brake doesn't fully release, you can manually
release the lever. Before attempting to release the
lever however, be sure to carefully read the
following paragraphs.
CAUTION:
Always shift to PARK (P) before pulling the
manual release lever. If your hand or arm is in
the way of the pedal you could be hurt. The pedal
springs back quickly. Keep your hand and arm
away when you use the manual release lever.
Before releasing the manual parking brake, be sure to
put the vehicle in PARK (P) and turn the ignition
to OFF.

2-31
Reach under the driver's side of the instrument panel
and pull on the manual release lever, which is located
above the parking brake pedal. If the parking brake does
not release, you should either drive to the nearest service
station or have your vehicle towed.
NOTICE:
Driving with the parking brake on can cause
your rear brakes to overheat. You may have to
replace them and you could also damage other
parts of your vehicle.
If you are towing a trailer and are parking on a hill, see
ªTowing a Trailerº in the Index. This section shows
what to do first to keep the trailer from moving. For
more information, see ªBrake Indicator Lightº in
the Index.

2-39
Express-Down Window
All power windows have this feature. Pressing the control
rearward to the second position then releasing it, will
lower a window completely. If you want to stop the
window as it is lowering, press the control forward briefly.
Press the control forward again to raise the window.
The first rearward position on the power window
control operates the driver's power window in the
non
-express mode.
Rear Window Lockout
Pressing this button down will disable the rear window
controls and cause the button to light, indicating that the
feature is in use. To restore power to the rear windows,
press the button again.
Horn
The horn can be sounded by pressing on the center of
the steering wheel pad.
Tilt Wheel and Telescopic Column
Tilt steering allows you to
adjust the steering wheel
before you drive. Raising
the steering wheel to the
highest level gives your legs
more room when you enter
and exit the vehicle.
This knob is located on the outboard side of the steering
column. Push up or down on the knob to adjust the tilt
of steering wheel. Then, push back or pull forward on
the knob, to adjust the height of the steering column.
Release the knob to lock the wheel and column
into place.
It is also possible to move the steering column to a
different position by momentarily pressing the
adjustment knob.

2-40
Turn Signal/Multifunction Lever
Turn and Lane Change Signals
To signal a turn, move the lever all the way up or down.
The lever returns automatically when the turn is complete.
An arrow on the instrument
panel will flash in the
direction of the turn or
lane change.
Raise or lower the lever until the arrow starts to flash to
signal a lane change. Hold it there until the lane change
is complete. The lever returns when it's released.
If the turn signal is left on, a warning chime will sound
and the Driver Information Center (DIC) will display
TURN SIGNAL ON (after driving about a mile) to
remind you to turn it off.
Arrows that flash rapidly when signaling for a turn or
lane change may be caused by a burned out signal bulb.
Other drivers won't see the turn signal.
Replace burned
-out bulbs to help avoid possible
accidents. Check the fuse (see ªFuses and Circuit
Breakersº in the Index) and for burned
-out bulbs if the
arrow fails to work when signaling a turn.
Headlamp High/Low Beam
Push forward for high beam to change the headlamps
from low beam to high. Pull the lever back and then
release it to change from high beam to low.
This light located on the
instrument panel will be on,
indicating high
-beam usage.
Flash-To-Pass
This lets you use the high beam headlamps to signal the
driver in front of you that you want to pass.
Pull and hold the turn signal lever toward you to use.
When you do:

If the headlamps are either off or in the DRL mode,
the high beam headlamps will turn on. They'll stay
on as long as you hold the lever there. Release the
lever to turn them off.

If the headlamps are on highbeam, they will switch
to low beam. To return to high beam, push the lever
away from you.

2-44
CAUTION:

Cruise control can be dangerous where you
can't drive safely at a steady speed. So,
don't use your cruise control on winding
roads or in heavy traffic.

Cruise control can be dangerous on
slippery roads. On such roads, fast changes
in tire traction can cause needless wheel
spinning, and you could lose control. Don't
use cruise control on slippery roads.
If your vehicle is in cruise control when the optional
traction control system begins to limit wheel spin, the
cruise control will automatically disengage. (See
ªTraction Control Systemº in the Index.) When road
conditions allow you to safely use it again, you may turn
the cruise control back on.Setting Cruise Control
CAUTION:
If you leave your cruise control switch on when
you're not using cruise, you might hit a button
and go into cruise when you don't want to. You
could be startled and even lose control. Keep the
cruise control switch off until you want to use
cruise control.
1. Press the CRUISE ON/OFF button to turn cruise
control on. (The button is located on the bottom left
of the steering wheel.) An indicator light will come
on to show that the cruise control is on.
2. Get up to the speed you want.
3. Press the SET/CST (coast) button. (The button is
located on the bottom right of the steering wheel.)
The CRUISE ENGAGED message will display on
the Driver Information Center (DIC).
4. Remove your foot from the accelerator pedal.

2-46
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise control speed you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down. Applying the brake or shifting
into a lower gear will take you out of cruise control. If
you need to apply the brake or shift to a lower gear due
to the grade of the downhill slope, you may not want to
attempt to use your cruise control feature.
Ending Cruise Control
To turn off the cruise control, step lightly on the brake
pedal, or press the CRUISE ON/OFF button on the
steering wheel.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.Exterior Lamps
This control on the left
side of the instrument
panel controls these
lamp systems:

Headlamps

Taillamps

Parking Lamps

Sidemarker Lamps

License Plate Lamp

2-47
Parking Lamps
Turn the lamp control knob clockwise to the first stop,
to turn on the parking, taillamps, sidemarker lamps. If it
is night, the instrument panel switch backlighting will
also illuminate. Turn the control knob counterclockwise
all the way back to turn the lamps and lights off.
Headlamps
Turn the control knob clockwise all the way to turn on
the parklamps and headlamps. Turn the control knob
counterclockwise to turn the lamps off.
Wiper
-Activated Headlamps
This feature activates the headlamps and parking lamps
after the windshield wipers have been in use for
approximately six seconds.
In order to operate the wiper
-activated headlamps, the
Twilight Sentinel
must be turned on; the ignition key
in the ON position and the windshield wipers on, or in a
delay setting. If the windshield wipers are active while
the ignition key is in ON, but the Twilight Sentinel
switch is off, a ªHeadlamps Suggestedº message will be
displayed on the Driver Information Center. This
message informs the driver that turning on the exterior
lamps is recommended.This feature lights the way in poor weather and it also
makes your vehicle more visible to other drivers. If the
wiper
-activated headlamps are on and the ignition
switch, Twilight Sentinel, or the wipers are turned off,
the wiper
-activated headlamps will immediately
turn off.
Lamps on Reminder
If the manual headlamp control is left on and a door is
opened, a warning chime will sound. An exception is
when the Twilight Sentinel function is active.
Daytime Running Lamps
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset.