2000 AUDI A6 light

37-62

Selector lever cable for shift mechanism
(without Tiptronic), removing and
installing


Note:

Do not bend or kink selector lever cable, lightly
grease coupling ring and coupling ends before
installing
Selector lever cable can best be removed in
selector lever position "P".

Removing:

- Remove shielding plate (below shift mechanism)
for exhaust system.

- Remove cover:
Disengage snap lock of cover by pressing in direction of arrow A
page 37
-59
.
- Disengage locking clip by pressing both ends together and pull selector
lever cable off selector lever.
- Pull out securing plate for selector lever cable at shift mechanism
housing downward.
- Insert with angled end toward the rear and in groove at selector lever
cable Fig. 1
, page 37
-64
.
Pa
ge 67 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-63

- Pull selector lever cable out of shift mechanism
housing.

- Remove shielding plate for selector lever cable
(item B).

Installing - Press retaining clip off of lever/shift lever (item C).
- Press ball socket of selector lever cable off of lever/shift rod.
- Loosen bracket from transmission (item D).
- If necessary, loosen selector lever cable from bracket (item E).
- Selector lever and lever/shift rod in position "P" (park lock must
engage).
- Installation is the reverse order of removal.
- Lightly grease coupling ring and ball socket of selector lever cable.
- Selector lever cable, checking and adjusting page 37
-45
.Pa
ge 68 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-66

Adjusting

- Place selector lever in position "P".

- Shift lever/shift lever to "P" (last position, shift
lock solenoid must engage).

- Slightly loosen mounting bolt at bracket to transmission.
Check freedom of stress of selector lever cable, if necessary
eliminate stress.
- Tighten mounting bolt of bracket to 23 Nm.
- Check shift mechanism page 37
-2 .
Pa
ge 71 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-68


- Set ignition/starter lock in "Drive" position.
- Shift selector lever into position "P".
- Lift up locking bracket -1- and pull locking cable
out of ignition/starter lock.
- Remove cover with guide (selector lever
mechanism) page 37
-5 .
- Unclip locking cable from securing spring at shift
mechanism housing, slightly lift up securing
spring to do so.
- Loosen cable tie -2- and remove locking cable.
Pa
ge 73 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-69


Installing and Adjusting
- Installation is the reverse of removal.
- Install locking cable without kinking and secure
at indicated position using cable tie -2-.
- Adjust steering column rearward/downward.
- Check locking mechanism of interior lever -1-.
- Slightly loosen bolt -6-.
- It must be possible to slide bracket -3- in
direction of arrow -5-.
- Make sure securing spring is correctly seated in
shift mechanism housing.
- Hook locking cable bracket -3- into shift
mechanism and locking coupling ring in lever (for
locking cable).
Pa
ge 74 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1