2000 AUDI A4 ignition

01-93

Function test: Traction control indicator light -K86-. This is only installed if vehicle is equipped with ASR.
Test step
VAG
1598/20
sockets Test of
Test
requirements
- Additional work
steps Specified value
Corrective action
21

Continuation: - Function of
traction
control
indicator light
-K86- - Switch on
ignition Traction control
indicator light -K86-
comes on for two
(2) seconds and
then goes out.
Electrical Wiring Diagrams,
Troubleshooting & Component
Locations - If traction control indicator light does
not light up, check vehicle voltage and
wire from terminal 31 of ABS control
module -J104- to instrument cluster for
short circuit to B+ and open circuit.
- If traction control indicator lamp
remains continuously lit, check wire
from terminal 31 of ABS control
module -J104- to instrument cluster for
short circuit to Ground (GND).

Repair Manual, Electrical
Equipment, Repair Group 90; Instrument cluster
- Are both the vehicle voltage and the
wiring from terminal 31 of ABS control
module -J104- to the instrument
cluster OK? Malfunction in
instrument cluster.
Pa
ge 48 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-94

Function test: Traction control button; set measurement range on VAG1526: 20 V =
Test
step VAG
1598/20
sockets Test of
Test requirements
- Additional work stepsSpecified value
Corrective action
22 - Function of
traction control
button Ignition switched off Function of traction control
indicator light -K86- was
already checked in step 21. Multi-pin connector connected
to ABS control module -J104-
and retainer catch engaged.
- Switch on ignition

- Press traction control buttonTraction control
indicator light -
K86- lights up - Switch off ignition.
- Detach multi-pin
connector from ABS control
module -J104- and remove.

- Press traction control button
again Traction control
indicator light -
K86- goes out. - Connect VAG1598/20 test
box.
Test step 22: Continued on next page.
Pa
ge 49 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-95

Function test: Traction control button; set measurement range on VAG1526: 20 V =
Test step
VAG
1598/20
sockets Test of
Test requirements
- Additional work
steps Specified
value Corrective action
22 28 + 44 Function of
traction control
button Ignition switched
on.
Continuation:
- Traction control
button not pressed 0.0 to 0.5
V

- Traction control
button pressed 10.0 to 14.5
V
Electrical Wiring Diagrams,
Troubleshooting & Component
Locations - Check wire from terminal 28 to
Ground (GND).
- Check wire from terminal 44 to
traction control button, terminal 6.
- Check voltage supply from terminal 5
of traction control button to terminal 15.
- If no malfunctions can be found using
the procedures in these steps, replace
the traction control button.
Pa
ge 50 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-96

Voltage measurement; set measurement range on VAG1526: 20 V =
Test
step VAG
1598/20
sockets Test of
Test
requirements
- Additional work
steps Specified
value Corrective action
23 1 + 28
1 + 29 Voltage supply to ABS
control module -J104- via
terminal 15 Ignition
switched on. 10.5 to 14.5
V
Electrical Wiring Diagrams,
Troubleshooting & Component
Locations - Check wiring from terminals 28
and 29 to Ground (GND).
- Check wire from terminal 1 to
terminal 15.
Pa
ge 51 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-97
Diagnostic Trouble Code (DTC) table

Notes:

Connect the VAG1551 Scan Tool (ST) and select address word 03 "Brake Electronics".
Check the control module version page 01
-52
and press the button.
Press buttons -0- and -2- to select "Check DTC Memory" function 02. Press -Q- button to confirm input.
Notes:
Each malfunction is assigned a 5-digit Diagnostic Trouble Code (DTC). The DTC is located in the left column of the DTC
table. If you have switched the printer on by pressing the "PRINT" button, the VAG1551 scan tool (ST) prints the message
identifying the malfunction and the DTC. Otherwise, DTCs are not displayed by the VAG1551 scan tool.
The contents of DTC memory remain stored until memory is erased, page 01
-15
.
Sporadically occurring malfunctions are identified via indication of "/SP" on the right-hand side of the display.
Static malfunctions that cannot be detected when the vehicle is stationary are also identified with "/SP" if the ignition has
been switched off and then on again.
The following DTC table includes all the DTCs that can be stored by the ABS control module -J104- and displayed and
printed out by the VAS5051 tester or VAG1551 scan tool. Malfunctions are listed by DTC number.
Pa
ge 52 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-118

Output on printer of VAG1551 Scan Tool (ST)
Possible cause
Corrective action
DTC

00668
Vehicle voltage terminal 30, open circuit

When equipped with EDL, the ABS control module
-J104- requires this voltage supply after ignition is
switched off in order to calculate the drop in brake
temperature; page 01
-39
.
Voltage supply to ABS control
module (w/EDL) -J104- (terminal
50) has an open circuit or short
circuit to Ground (GND). Electrical Wiring
Diagrams, Troubleshooting
& Component Locations - Check wire connection.
Pa
ge 78 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8