2000 AUDI A4 manual transmission

01-163
Display group 000
Note:
If the values displayed do not correspond to the specified values, the following display groups 001 to 010 can be used to
repair malfunctions. Display
field Specified
display value Corresponds to
physical values Designation and conversion to physical values
1 135 - 160
85 - 110 C
Momentary coolant temperature, display -50 = ___ C
2 145 - 158 1.45 - 1.58 V Mass Air Flow (MAF) sensor output voltage, display: 100 = 1 V
3 26-30 650-750 RPM Momentary engine speed, display X 25 = ____RPM
4 0 - 14
or
255 - 240 Idle speed control learning value, with manual transmission in idle
position and/or with automatic transmission with selector lever setting
P or N (average = 0)
5 0 -10
or
255 - 236 Idle speed control learning value, with automatic transmission in
selector lever setting D 1, 2, 3 or R (average = 0)
(On manual transmission vehicles, 0 is always displayed.)
6 126 - 130 Idle speed control feedback (average 128)
7 20 Shift inputs
8 120-136 Oxygen sensor control (average 128/cylinders 1 to 3) "0" is always
displayed on engines without oxygen sensor probe.
Pa
ge 227 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-166
Test table display group 001 Display
field Display on
VAG 1551 scan
tool Malfunction cause
Malfunction repair
1 Greater than
110
or
Less than 85
Engine Coolant Temperature (ECT)
sensor -G62-
Wiring connection to Engine Control
Module (ECM) -J192-
Coolant thermostat faulty
Repair Manual, 2.8 Liter V6 2V Engine
Mechanical, Engine Code(s): AFC, Repair Group 19
- Check DTC memory page 01
-13
- Check -G62- page 28
-25
- Check engine coolant thermostat
2 Less than 1.450
V
Large intake air leak between intake
manifold and Mass Air Flow (MAF)
sensor Repair cause
Greater than
1.580 V Electrical consumers on, steering wheel
at end stop, driving mode selected
(automatic transmission)
Tolerance for new engines: - Switch consumers off
- Center steering wheel
- Put selector lever in P or N position
display group 004, display field 4
Max. 1.660 V
When engine speed increases, the display
value increases to 2.500 V, falls to 0.000 V
Pa
ge 231 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-169

Display
field Display on VAG
1551 scan tool Malfunction cause
Malfunction repair
3 Outside tolerance
range
Closed Throttle Position (CTP)
switch activated or faulty CTP switch or throttle position
sensor -G69- incorrectly adjusted Electrical consumers onSteering wheel at end stopDriving mode selected (automatic
transmission) Moisture in connector for -G69-Ground point on intake manifold - Check DTC memory page 01
-13
- Check and adjust -G69- page 24
-77
- Switch electrical consumers off
- Center steering wheel
- Selector lever in P or N display group 004,
display field 4 - Visual inspection
- Check ground connection according to wiring
diagram
4 0 or 1
Closed Throttle Position (CTP)
switch -F60- faulty Throttle position sensor -G69-
incorrectly adjusted Throttle sticks Floor mat presses against
accelerator pedal Moisture in connector of -G69-Accelerator pedal cable adjustment Display group 011, display field 4
Repair Manual, 2.8 Liter V6 2V Engine
Mechanical, Engine Code(s): AFC, Repair Group 20
- Check DTC memory page 01
-13
- Check and adjust -F60- page 24
-73
- Visual inspection
- Adjust accelerator pedal cable:
Pa
ge 235 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-170
Display group 003 Display shows
Display/specified value
Designation
Basic setting 3
1 2 3 4 650 - 750 RPM 1 = Momentary idle speed
15.0 - 35.0% 2 = Engine load idle1)
0% and/or greater than 95% 3 = Throttle angle - at idle: 0%; at wide open throttle: > 95%
... km/h 4 = Momentary vehicle speed 1) Evaluate engine load tolerance range only at idle during "Basic Setting" function 04.
Note on display field 1:
Idle speed on vehicles without A/C and rear windshield heater switched on: 750-850 RPM.
Notes on display field 3:
For the testing at wide open throttle, stop engine, and switch ignition on.
Since in vehicles with manual transmission and automatic transmission different throttle bodies are installed, the start of
opening of the throttle body can be measured with ignition on and thus incorrect installation can be checked
Manual transmission: 45-53%
Automatic transmission: 27-35%
Pa
ge 237 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-173
Display group 004 Display
shows Display/specified
value Designation
Basic
setting 4
1 2 3 4 0 2
1 = Idle air control valve at idle
HS: +14 to -16
or
AT: +10 to -20 2 = Idle speed control learning value in manual transmission (HS) at idle setting and/or
with automatic transmission (AT) in selector lever setting P or N
Variation permitted for new engines:
HS: +20 to -16AT: +16 to -20)
HS: 0
or
AT: +10 to -20 3 = Idle speed control learning value in automatic transmission (AT) in selector lever
setting D, 1, 2, 3 or R. (0 is always displayed in vehicles with manual transmission.)
001 10 4 = Shift inputs at idle:
0 off 1 on
Notes:

Values in display fields 2 and/or 3 can only be evaluated with idle air control valve is within tolerance at idle (display value
1). If the idle air control valve is not within tolerance after 1 minute waiting time, no learning takes place in display fields 2
and/or 3 .
Pa
ge 242 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-209
Display group 027 Display
shows Display specified
value Designation/diagnosis
Basic setting
27
1 2 3 4 X 1 = Malfunction Indicator Lamp (MIL) wire from Transmission Control Module
(TCM)
X 2 = Fuel level signal from instrument cluster
0.000 V 3 = ---------------
0.000 V 4 = --------------- Notes on display field 1:

On vehicles with manual transmission, "1" is always displayed.
Checking Malfunction Indicator Lamp (MIL) wire from transmission control module page 24
-105
.
X
Meaning of the 1-digit display:

Value "0" = ignition on, engine not running
Value "1" = engine running Note on display field 2:

Check fuel level signal from instrument cluster page 24
-107
.
Pa
ge 296 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-211
Display group 029 (Diagnosis status)
Notes:
OBD II regulations require a display ("Readiness Code") that indicates readiness for inspection (annual exhaust emissions
test). The readiness code display (display field 1) shows that every component and/or system that affects the exhaust, which
can lead to switching on the MIL, has been operated at least once with positive result.
The readiness code is reset and/or erased:

Every time the DTC memory is erased (both with address word 01 function 05 and with address 33 mode 4).
When the battery is disconnected.
When the engine control module is disconnected (e.g. connecting test box VAG 1598/19, replacing ECM, etc.).
To generate the readiness code, take a "mixed city and highway" drive (short test). A "mixed city and highway" drive is
understood to be approx. 1-1/2 to 5 minutes at 80-100 km/h (50-63 mph) with manual transmission in 4th or 5th gear, or
automatic transmission selector lever in "D" position, preferably in 4th gear.
The "Trip Status" display (display field 2) shows which components and/or systems have been checked since the start of the
trip. After successful diagnosis, the current display value is set to "1" whether the diagnosis was recognized as OK or not OK.
The trip-status display is reset to "0" at each start since the components and/or systems are checked at each new start. A
"trip" is understood to be a drive of approx. 1-1/2 to 5 minutes at 80-100 km/h (50-63 mph) with manual transmission in 4th or
5th gear, or automatic transmission selector lever in "D" position, preferably in 4th gear, with preceding cold start.
The readiness code display (display field 1) shows whether the components and/or systems checked in display field 2 were
recognized as OK or not OK by the engine control module.
If the diagnosis is recognized as OK, the current display value is set to "0."
Pa
ge 299 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-213
Notes on display field 1:

All readiness code values are set to "1" by disconnecting the ECM harness connector and/or disconnecting the battery,
and every time DTC memory is erased (both with address word 01 function 05 and with address word 33 mode 4).
To regenerate the readiness code, take a drive of approx. 1-1/2 to 5 minutes at 80-100 km/h (50-63 mph) with manual
transmission in 4th or 5th gear, or automatic transmission selector lever in "D" position, preferably in 4th gear ("mixed city
and highway" trip).
Value "0" = Diagnosis carried out
Value "1" = Diagnosis not OK and/or diagnosis not carried out yet
X
X
X

X
X

X
Meaning of the 6-digit "readiness codes"

1 = Three way catalytic converter diagnosis (Banks 1 and 2)

2 = ----

3 = Evaporative Emissions (EVAP) throughput diagnosis

4 = Secondary air system throughput and leak diagnosis (Always "0" for vehicles without
secondary air injection system)

5 = ----

6 = Heated oxygen sensor diagnosis (flank rise and/or flank fall time of the voltage signal of
heated oxygen sensors in front of three way catalytic converters

7 = Oxygen sensor heating diagnosis (all four O2S heaters)

8 = Exhaust Gas Recirculation (EGR) throughput diagnosis
Pa
ge 303 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1