2000 AUDI A4 heating

01-99

Output on GST and/or
on VAG 1551 scan tool
Possible malfunction cause

Malfunction repair
P1107 / 17515
Heating Circ. (B2-S1)
Short to B+ Harness connector for Oxygen Sensor
(O2S) heater -Z28- (B2-S1) loose or
corroded due to moisture in the harness
connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately Wiring connection of Oxygen Sensor
(O2S) heater -Z28- (B2-S1) faulty, or heater
-Z28- faulty

- Check O2S heater -Z28- (B2-S1) page 24
-51


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
For troubleshooting
Display group 040
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
erase DTC memory and
test drive check DTC memory
Notes:

The heating of the oxygen sensor probes in front of Three Way Catalytic Converter (TWC) is switched on with the fuel
pump relay, i.e. immediately at engine start.
Pa
ge 131 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

The malfunction "P1107 / 17515" is set after engine start as soon as the heating current is greater than 10 A for longer
than 80 ms at a battery voltage between 9 V and 16 V.
Pa
ge 132 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-102

Output on GST and/or
on VAG 1551 scan tool
Possible malfunction cause

Malfunction repair
P1110 / 17518
Heating Circ. (B2-S2)
Short to B+ Harness connector for Oxygen Sensor
(O2S) heater -Z30- (B2-S2) loose or
corroded due to moisture in the harness
connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Wiring connection for Oxygen Sensor
(O2S) heater -Z30- (B2-S2) faulty, or heater
-Z30- faulty

- Check O2S heater -Z30- (B2-S2) page 24
-55


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
For troubleshooting
Display group 040
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
erase DTC memory and
test drive check DTC memory
Notes:

The heating for Oxygen Sensor Probes behind Three Way Catalytic Converter (TWC) is not switched on immediately at
engine start, but when the calculated exhaust gas temperature drops below 308 C (586 F) ( Read measuring value
Pa
ge 136 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

block, display group 42, channel 1).
The malfunction "P1105 / 17513" is set as soon as the probe heater is switched on (the vehicle must be driven approx. 60
sec. under load) and the heating current is greater than 10 A for longer than 80 ms.
Pa
ge 137 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-161

Display
group Display
shows Designation
036 Basic
setting 36
1 2 3 4 Three way catalytic convertor diagnosis, bank 2
037 Basic
setting 37
1 2 3 4 Sensor wheel learning value
038 Basic
setting 38
1 2 3 4 Current data on combustion misfiring recognition
039 Basic
setting 39
1 2 3 4 Statistical data on combustion misfiring recognition
040 Basic
setting 40
1 2 3 4 Heating current of heated oxygen sensors in front of and behind three way catalytic convertors
041 Basic
setting 41
1 2 3 4 Voltage signals of heated oxygen sensors in front of and behind three way catalytic convertor
042 Basic
setting 42 Diagnostic conditions for diagnosing the flank rise and flank fall time (response time) of the
voltage signals of the heated oxygen sensors in front of three way catalytic convertors
Pa
ge 224 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-176

Display
field Display on VAG 1551
scan tool Malfunction cause
Malfunction repair
4 Not 001 10
Closed Throttle Position (CTP) switch -F60 activated or faulty A/C compressor switched on Rear window heating switched on Driving mode selected (automatic
transmission) - Check and adjust -F60- page 24
-
73

- Switch A/C off
- Check A/C compressor shut-off
page 24
-90

- Move selector lever to P or N
Note:
Display field 4 (shift inputs) can be used to recognize whether the components described below are recognized by the Engine
Control Module (ECM) as switched on or off. Display group 023 gives an exact description of the shift inputs. 0
0
1

1
0
Meaning of 5-digit shift inputs

1 = Shifting Signal (0 = not active / 1 = active)

2 = Gear recognition signal (always "1" except that display = "0" for automatic transmission vehicles with
gear engaged)

3 = -----------

4 = Mechanical Closed Throttle Position (CTP) switch (1 = closed / 0 = open)

5 = A/C compressor OFF/ON (0 = off, 1 = on)

6 = Rear window heater signal (always "0" except for vehicles without A/C and with rear window heater
on)
Pa
ge 247 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-178
Test table display group 005 and/or display group 006 Display
fields Display on
VAG 1551
scan tool Malfunction cause
Malfunction repair
1, 2, 3, 4 Low oxygen
sensor learning
values
If first learning value in display field 1 is low, but
learning value in display fields 2, 3 and 4 normal:
oil dilution (large amount of fuel in the oil), fuel
injector leaks - Pull off cylinder block breather hose
and close
- If problem disappears after drive on
expressway and/or oil change
- Check fuel injector page 24
-29
If all four oxygen sensor learning values very low
overall:
- Fuel system pressure too high
- EVAP canister purge regulator valve -N80- open
continuously - Check system and residual pressure
page 24
-20

- Check -N80- page 24
-58
and/or
display group 009, display field 3
and/or display group 001, display field
2


Mass Air Flow (MAF) sensor -G70- faulty
Oxygen sensor (O2S) heating faulty or Heated
Oxygen Sensor (HO2S) dirty - Check MAF sensor -G70 page 24
-
81

- Check HO2S and O2S heating
page 24
-49
and/or display group 010,
display fields 1 and 2
Pa
ge 250 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-179

Display
fields Display on VAG
1551 scan tool Malfunction cause
Malfunction repair
1, 2, 3, 4 High oxygen
sensor learning
values
If learning value in display field 1 is low, but
learning value in display fields 2, 3 and 4
normal: air leak in manifold area possible
Fuel injector plugged - Repair cause
- Check fuel injector page 24
-29
If all four oxygen sensor learning values are very
high overall:
- Mass Air Flow (MAF) sensor -G70- faulty
- Fuel system pressure too low (fuel supply)
- Intake air leak between sensor -G70- and throttle
body
- Intake air leak in manifold gasket - Check MAF sensor -G70 page 24
-
81
and/or display group 001, display
field 2
- Check system and residual pressure
page 24
-20

- Repair cause


Oxygen sensor (O2S) heating faulty or Heated
Oxygen Sensor (HO2S) dirty - Check HO2S and O2S heating
page 24
-49
and/or display group 010,
display fields 1 and 2
Pa
ge 251 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1