2000 AUDI A4 clutch

01-45

Notes:

If a DTM component fails to respond as
specified, perform all corrective actions, checks
and tests recommended in output DTM table
page 01
-46
.

A/C system component locations: engine
compartment page 87
-96
(note specific
model year information).

A/C system component locations: passenger
compartment page 87
-106
(note specific
model year information).

Output DTM can be ended by pressing the -C-
button.
After ending output DTM, check DTC memory
page 01
-18
.

If the readout "function unknown or cannot be
carried out at the moment" appears in the
display at the start of output DTM, e.g. when
engine not running, press button and once
again select "function 03 Output Diagnosis Test
Mode (DTM)" (DTM component "A/C Clutch
N25" is no longer actuated for this test).
Pa
ge 63 of 91 A/C s
ystem, On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.HA01.01.1

01-46
Output Diagnostic Test Mode (DTM) table

VAG1551 scan tool display
Specified function
Corrective action
A/C Clutch N25








Notes: - N25 clicks every 2-seconds
- Output of A/C control head -E87- is switched from 0 V to
12 V every 2-seconds2) - Test voltage supply for -
N25- (via A/C Clutch
Relay J44) using wiring
diagram
- Repair or replace -N25-
page 87
-90

- Test circuit and
connectors between A/C
control head -E87-, J44
and -N25- using wiring
diagram
- Replace -E87-

"A/C compressor on" output to
Engine Control Module (ECM)
and -E87- terminal -C12- is
also actuated at the same
time1)
Output of -E87- switched from 0 V to 12 V every 2
seconds can be confirmed by switching compressor on
and off using the "ECON" button while reading the
measured value block of engine control module
Repair Manual, Fuel Injection and Ignition System,
Repair Group 01)

1)Test this "A/C compressor on" signal only if complaints exist. ECM uses signal to compensate for engine load when
compressor engages Repair Manual, "Fuel Injection & Ignition," Repair Group 24 . ECM is capable of switching off the A/C compressor from this signal. Confirm via function 08, Read measuring value block,
page Page 01
-63
, display group 01 and Fuel Injection and Ignition System Repair Manual, Repair group 01: Read
measured value block of ECM with engine running and at same time switch compressor on and off.
Pa
ge 65 of 91 A/C s
ystem, On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.HA01.01.1

2)A/C Clutch -N25- cannot be actuated during Output DTM when certain compressor cut-off conditions exist, page 01
-63
,
Read measuring value block.
Pa
ge 66 of 91 A/C s
ystem, On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.HA01.01.1