2000 Acura Integra ignition

Mirror
s
Keep the inside and outside mirrors
clean and adjusted for best visibility.
Be sure to adjust the mirrors before
you start driving. The inside mirror has day and night
positions. The night position reduces
glare from headlights behind you. Flip the tab on the bottom edge of
the mirror to select the day or night

position.
Adjusting the Power Mirrors

Adjust the outside mirrors with the adjustment switch on the driver's

door:

1. Turn the ignition switch ON (II).
2. Move the selector switch to L (driver s side) or R (passenger's

side).

CONTINUED

Instrument s an d Control s

SELECTO
R SWITC H

TA B

Digita
l Cloc k

The digital clock displays the time
with the ignition switch ON (II). To see the time with the ignition off,
press and hold the wide button next
to the clock. To set the clock:
1. Turn the ignition switch ON (II) to

display the time.

2. Swing down the front cover of the wide button next to the clock
display. You will see H, M, and
RESET buttons.
3. Press and hold the H button until
the hour advances to the desired
hour.
4. Press and hold the M button until the numbers advance to the

desired minutes.

You can use the RESET button to quickly set the time to the nearest
hour. If the displayed time is before
the half hour, pressing RESET
button sets the clock back to the previous hour. If the displayed time
is after the half hour, pressing the RESET button sets the clock for- ward to the beginning of the next
hour.
For example: 1:06 would RESET to 1:00. 1:52 would RESET to 2:00.

Instrument s an d Control s

RESE
T
HM

Consol
e Compartment , Cigarett e Lighte r
Consol e Compartmen t
To open the console compartment, pull up the front edge of the lid.
To close, lower the lid and push it down until it latches. The pocket on the underside of the
console compartment lid can be used
to hold cards. Cigarett
e Lighte r
The ignition switch must be in
ACCESSORY (I) or ON (II) for the
cigarette lighter to work. To heat up
the lighter, push it in. It will pop out
when it is ready for use. Do not hold
the lighter in while it is heating up,
you could cause it to overheat.
Instrument s an d Control s

CIGARETT
E LIGHTE R

CAR
D HOLDE R

CONSOL E COMPARTMEN T

Audi
o Syste m
Operatin g th e Radi o
The ignition switch must be in
ACCESSORY (I) or ON (II) to operate the audio system. Turn the
system on by pushing the PWR/
VOL knob. Adjust the volume by turning the same knob.
The band and frequency that the
radio was last tuned to is displayed.
To change bands, press the AM/FM
1 .
2 button. On the FM band, ST will
be displayed if the station is broad-
casting in stereo. Stereo reproduc-
tion on AM is not available. You can use any of three methods to
find radio stations on the selected
band: TUNE, SEEK, or the Presetbuttons.
TUN E — Use the TUNE bar to tune
the radio to a desired frequency. Press the side of the bar to tune
to a higher frequency, and the side to tune to a lower
frequency. The frequency numbers
will start to change rapidly. Release the bar when the display reaches the
desired frequency. To change the
frequency in small increments, press
and release the TUNE bar quickly. SEE
K — The SEEK function
searches the band for a station with
a strong signal. To activate it, press the SEEK bar on either the or
side, then release it.
Depending on which side you press,
the system scans upward or down- ward from the current frequency. It
stops when it finds a station with a
strong signal.
Prese t — You can store the
frequencies of your favorite radio
stations in the six preset buttons.
Each button will store one frequency
on the AM band, and two
frequencies on the FM band.
CONTINUED
Comfor t an d Convenienc e Feature s

Audi
o Syste m

If you turn the system off while a CD

is playing, either with the PWR/VOL
knob or by turning off the ignition,

the disc will stay in the drive. When

you turn the system back on, the CD

will begin playing where it left off.

Press the eject button to remove the
disc from the drive.

If you eject the disc, but do not
remove it from the slot, the system

will automatically reload the disc
after 15 seconds and put the CD

player in pause mode. To begin

playing the disc, press the CD button.
You can use the TUNE and SEEK
bars while a disc is playing to select

passages and change tracks.

To move rapidly within a track, press
and hold the TUNE bar. Press the
side to move forward, or the

side to move backward.

Release the bar when the system

reaches the point you want.
Each time you press the side of
the SEEK bar, the system skips
forward to the beginning of the next track. Press the side to skip
backward to the beginning of the
current track. Press it again to skip
to the beginning of the previous track.
REPEA T — To activate the Repeat
feature, press and release the Repeat
button. You will see RPT in the
display. The system continuously
replays the current track. Press the
Repeat button again to turn it off. RANDO
M PLA Y — This feature,
when activated, plays the tracks on the CD in random order, rather than
in the order they are recorded on the
CD. To activate Random Play, press and hold the A. SEL/RPT button
until you see A. SEL in the display.
The system will then select and play tracks randomly. This continuesuntil you deactivate Random Play by
pressing A. SEL/RPT again.
If the system is in Repeat mode, you
must turn it off by pressing A. SEL/
RPT before you can select Random
Play. Then press and hold the button
again until you see A. SEL displayed.
Comfor t an d Convenienc e Feature s

Audi
o Syste m

Operatin g th e Optiona l Cassett e

Playe r

The cassette system features Dolby
B* noise reduction, automatic sensing of chromium-dioxide (CrO 2)
tape, and autoreverse for continuous

play.

Make sure the tape opening on the
cassette is facing to the right, then
insert the cassette most of the way
into the slot. The system will pull itin the rest of the way, and begin to

play.

* Dolby noise reduction manufactured under

license from Dolby Laboratories Licensing Corpo-
ration. "DOLBY" and the double-D symbol
are trademarks of Dolby Laboratories

Licensing Corporation.
The tape direction indicator will light
to show you which side of the cassette is playing. The indicates
the side you inserted facing upward is now playing. If you want to play
the other side, press the PROG

button.

Dolby B noise reduction turns onwhen you insert a cassette. If the
tape was not recorded with Dolby B noise reduction, turn it off by
pressing the NR button.
When the system reaches the end of
the tape, it will automatically reverse direction and play the other side. If
you want to remove the cassette
from the drive, press the EJECT
button.
If you turn the system off while a
tape is playing, either with the PWR/
VOL knob or by turning off the
ignition, the cassette will remain in
the drive. When you turn the system
back on, the tape will begin playing
where it left off.
To switch to the radio or CD player
while a tape is playing, press the AM/FM1-2 or CD button. To change
back to the cassette player, push theCD button.

Comfor t an d Convenienc e Feature s

Preparin
g to Driv e
You should do the following checks and adjustments every day before
you drive your car.
1. Make sure all windows, mirrors, and outside lights are clean and
unobstructed. Remove frost, snow,
or ice.
2. Check that the hood and trunk are fully closed.
3. Visually check the tires. If a tire looks low, use a gauge to check its

pressure.

4. Check that any items you may be carrying with you inside are stored
properly or fastened down
securely.
5. Check the adjustment of the seat
(see page 75 ).
6. Check the adjustment of the inside and outside mirrors (see
page 81 ).
7. Check the adjustment of the steering wheel (see page 65 ).
8. Make sure the doors are securely
closed and locked.

9. Fasten your seat belt. Check that
your passengers have fastened

their seat belts (see page 15 ). 10.Turn the ignition switch ON (II).
Check the indicator lights in the
instrument panel.
11.Start the engine (see page 133 ).
12.Check the gauges and indicator lights in the instrument panel (see
page 53 ).
Drivin g

Startin
g th e Engin e

1. Apply the parking brake.
2. In cold weather, turn off all electrical accessories to reduce
the drain on the battery.

3. Manual Transmission:
Push the clutch pedal down all the
way. START (III) does not
function unless the clutch pedal is

depressed.

Automatic Transmission:

Make sure the shift lever is in
Park. Press on the brake pedal.
4. Without touching the accelerator pedal, turn the ignition key to the
START (III) position. If the enginedoes not start right away, do not
hold the key in START (III) for
more than 15 seconds at a time.
Pause for at least 10 seconds
before trying again. 5. If the engine does not start within
15 seconds, or starts but stalls
right away, repeat step 4 with the
accelerator pedal pressed half-way
down. If the engine starts, release
pressure on the accelerator pedal
so the engine does not race.
6. If the engine still does not start, press the accelerator pedal all the
way down and hold it there while
starting in order to clear flooding.
As before, keep the ignition key in
the START (III) position for no
more than 15 seconds. Return to
step 5 if the engine does not start.
If it starts, lift your foot off the
accelerator pedal so the engine
does not race.

Startin g in Col d Weathe r a t Hig h

Altitud e (Abov e 8,00 0 feet /

2,40 0 meters )

An engine is harder to start in cold weather. The thinner air found at
high altitude above 8,000 feet (2,400 meters) adds to the problem.
Use the following procedure:
1. Turn off all electrical accessories to reduce the drain on the battery.
2. Push the accelerator pedal half- way to the floor and hold it there
while starting the engine. Do not
hold the ignition key in START
(III) for more than 15 seconds.
When the engine starts, release
the accelerator pedal gradually as
the engine speeds up and smooths
out.
3. If the engine fails to start in step 2, push the accelerator pedal to the
floor and hold it there while you
try to start the engine for no more
than 15 seconds. If the engine
does not start, return to step 2.

Driving