2000 Acura Integra open hood

Befor
e Drivin g
Before you begin driving your Acura,
you should know what gasoline to use, and how to check the levels of
important fluids. You also need to
know how to properly store luggageor packages. The information in thissection will help you. If you plan to
add any accessories to your car,
please read the information in this section first. General Precautions...................... 122
Break-in Period.............................. 123
Gasoline.......................................... 123
Service Station Procedures.......... 124 Filling the Fuel Tank................. 124Opening the Hood..................... 125
Oil Check................................ 127
Engine Coolant Check.......... 128
Fuel Economy................................ 129
Vehicle Condition...................... 129Driving Habits............................ 129
Accessories and Modifications.... 130 Carrying Cargo.............................. 132

Before Drivin g

Servic
e Statio n Procedure s
5. Screw the fuel fill cap back on,
tighten it until it clicks at least
three times. If you do not properly
tighten the cap, the Malfunction Indicator Lamp may come on (see
page 237).

6. Push the fuel fill door closed until

it latches.

Openin g th e Hoo d
1. Shift to Park or Neutral and set

the parking brake. Pull the hood release handle located under the
lower left corner of the dashboard.
The hood will pop up slightly.

2. Standing in front of the car, put

your fingers under the front edge of the hood to the left of center.
Slide your hand to the right until
you feel the hood latch handle. Push this handle to the right until
it releases the hood. Lift the hood.

CONTINUED
Befor e Drivin g

LATC
H
HOO D RELEAS E HANDL E

Servic
e Statio n Procedure s
If you can open the hood without
lifting the hood latch handle, or the hood latch handle moves stiffly ordoes not spring back as before, the
mechanism should be cleaned and
lubricated (see page 187).
3. Pull the support rod out of its clipand insert the end into the hole on
the left side of the hood. To close the hood, lift it up slightly to
remove the support rod from the
hole. Put the support rod back into
its holding clip. Lower the hood to about a foot (30 cm) above the
fender, then let it drop.
After closing the hood, make sure it is securely latched.

Befor e Drivin g
SUPPOR
T RO D

CLIP

Engin
e Oi l
1. Run the engine until it reaches
normal operating temperature,
then shut it off.

2. Open the hood and remove the

engine oil fill cap. Remove the oil drain bolt and washer from thebottom of the engine. Drain the oil
into an appropriate container.

3. Remove the oil filter and let the

remaining oil drain. A special
wrench (available from your Acura dealer) is required to remove the
filter.

4. Install a new oil filter according to

instructions that come with it.

Maintenanc e
WASHE
R

OI L DRAI N BOL T OI
L FILTE R

Coolin
g Syste m
Do not add any rust inhibitors or other additives to your car's cooling
system. They may not be compatible
with the coolant or engine compo-
nents.

Replacin g Engin e Coolan t
The cooling system should be completely drained and refilled with
new coolant according to the time
and distance recommendations in
the maintenance schedule. Only use Genuine Honda Antifreeze/Coolant.
Draining the coolant requires access
to the underside of the car. Unless
you have the tools and knowledge,
you should have this maintenance done by a skilled mechanic. 1. Turn the ignition ON (II). Slidethe heater temperature control
lever to maximum heat. Turn the ignition off.
2. Open the hood. Make sure the
engine and radiator are cool to the touch.
3. Remove the radiator cap. 4. Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the splash guard. Remove the drainbolt and washer from the engine block.
Maintenanc e DRAI
N PLU G
DRAI
N
BOL T

Light
s

Headligh t Aimin g
The headlights were properly aimed when your car was new. You should check their aim if you regularly carry
heavy items in the cargo area or pull a trailer. Each headlight assembly
has horizontal and vertical adjust-
ment indicators. These are set to
their "0" positions after the head-
lights are aimed at the factory. To check these settings:
1. Make sure the fuel tank is full.

Park the car on level ground.
2. The driver or someone who

weighs the same should be sitting in the driver's seat for all checks
and adjustments.
Load your vehicle with the items
you normally carry.

If you usually pull a trailer, load it as
you would normally and attach it to the car. Push down on the front and
rear bumpers several times to makesure the car is sitting normally. 3. Open the hood.
4. Check the horizontal angle gauge.

The line on the adjustment screw
indicator should line up with the"0" mark on the gauge.

CONTINUED

Maintenanc e
HORIZONTA
L ANGL E GAUG E

Lef t headligh t
Right headligh t

Light
s

Replacin g a Headligh t Bul b
Your car has two bulbs on each side, four in total. Make sure you arereplacing the bulb that is burned out.
Your car uses halogen headlight bulbs. When replacing a bulb, handle
it by its plastic case and protect the
glass from contact with your skin or
hard objects. If you touch the glass,clean it with denatured alcohol and a
clean cloth.

Halogen headlight bulbs get very hot when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.
1. Open the hood.
If you need to change the high
beam headlight bulb on the
passenger's side, remove the
radiator reserve tank by pulling it straight up.

2. To disconnect the bulb from the

electrical harness, push on the end
of the lock tab to release the
connector then push the connec-
tor straight down.

3. Turn the bulb about one-eighth

turn counterclockwise to unlock it
from the headlight assembly.

4. Remove the bulb by pulling it

straight out of its recess.

5. Align the tabs on the new bulb
with the slots in the headlightassembly and push it into place.
6. Turn the bulb clockwise to lock it

in place. Do not force it. Check the seating of the bulb's tabs in the
slots if the bulb will not return to
its original position.

7. Reinstall the harness connector on

the bulb connector. Make sure it
locks in place.
Turn on the headlights to test the new bulb.

8. (Passenger's side)

Reinstall the radiator reserve tank.

Maintenanc e

NOTIC
E

I
f You r Engin e Won' t Start , Jum p Startin g
Th e Starte r Operate s Normall y
In this case, the starter motor's speed sounds normal, or even faster
than normal, when you turn the ignition switch to START (III), but
the engine does not run. Are you using the proper starting
procedure? Refer to Startin g th e
Engin e on page 137. Do you have fuel? Turn the
ignition switch to ON (II) for a
minute and watch the fuel gauge.
The low fuel level warning light may not be working, so you were
not reminded to fill the tank. There may be an electrical
problem, such as no power to the
fuel pump. Check all the fuses (see page 240).
If you find nothing wrong, you will
need a qualified technician to find
the problem. See Emergenc y
Towin g on page 245 . Jum
p Startin g
If your car's battery has run down,
you may be able to start the engine
by using a booster battery. Although this seems like a simple procedure,
you should take several precautions.
You cannot start an Acura with an automatic transmission by pushing
or pulling it. To jump start your car, follow these
directions closely:
1. Open the hood and check the
physical condition of the battery(see page 189). In very cold
weather, check the condition of
the electrolyte. If it seems slushy or like ice, do not try jump starting
until it thaws.

If a battery sits in extreme cold, the
electrolyte inside can freeze.
Attempting to jump start with a frozen battery can cause it to rupture.

2. Turn off all the electrical acces-

sories: heater, A/C, stereo system,
lights, etc.
Put the transmission in Neutral or
Park and set the parking brake.

CONTINUED

Takin g Car e o f th e Unexpecte d

NOTIC
E
A battery can explode if you do
not follow the correct procedure,

seriously injuring anyone
nearby.

Keep all sparks, open flames,

and smoking materials away

from the battery.