1999 YAMAHA YZF-R7 key

EC080000
HOW TO USE
THIS MANUAL
EC081000
PARTICULARLY IMPORTANT
INFORMATION
The Safety Alert Symbol means ATTEN-
TION! BECOME ALERT! YOUR SAFETY IS
INVOLVED!
Failure to follow WARNING instructions
could result in severe injury or death to the
machine operator, a bystander, or a person
inspecting or repairing the motorcycle.
A CAUTION indicates special precautions
that must be taken to avoid damage to the
motorcycle.
NOTE:
A NOTE provides key information to make
procedures easier or clearer.
WARNING
CAUTION:

EC082000
FINDING THE REQUIRED PAGE
1. This manual consists of eight chapters;
“General Information”, “Specifica-
tions”, “Periodic checks and adjust-
ments”, “Engine”, “Cooling system”,
“Electronic fuel injection”, “Chassis”,
“Electrical”.
2. The table of contents is at the begin-
ning of the manual. Look over the gen-
eral layout of the book before finding
the required chapter and item.
Bend the book at its edge, as shown, to
find the required fore edge symbol
mark and go to a page for required
item and description.

1 - 4
INSTRUMENT AND CONTROL FUNCTIONS
INSTRUMENT AND CONTROL FUNCTIONS
EAU00029
Main switch/Steering lock
The main switch controls the ignition
and lighting systems. Its operation is
described below.
EAU00036
ON
Electrical circuits are switched on. The
engine can be started. The key cannot
be removed in this position.
EAU00038
OFF
All electrical circuits are switched off.
The key can be removed in this posi-
tion.
EAU00040
LOCK
The steering is locked in this position
and all electrical circuits are switched
off. The key can be removed in this po-
sition. To lock the steering, turn the
handlebars all the way to the left. While
pushing the key into the main switch,
turn it from “OFF” to “LOCK” and re-
move it. To release the lock, turn the
key to “OFF” while pushing.
1. Push
2. Turn
EW000016
WARNING

Never turn the key to “OFF” or
“LOCK” when the motorcycle is
moving. The electrical circuits will
be switched off which may result in
loss of control or an accident. Be
sure the motorcycle is stopped be-
fore turning the key to “OFF” or
“LOCK”.
EAU01574
(Parking)
The steering is locked in this posi-
tion, and the taillights and auxiliary
lights come on, but all other circuits
are off. The key can be removed in
this position.
To use the parking position, first
lock the steering, then turn the key
to “ ”. Do not use this position for
an extended length of time as the
battery may discharge.
1.
Neutral indicator light “ ”
2. High beam indicator light “ ”
3. Turn indicator light “ ”
4. Fuel indicator light “ ”
EAU00056
Indicator lights
EAU00061
Neutral indicator light “ ”
This indicator comes on when the
transmission is in neutral.
EAU00063
High beam indicator light “ ”
This indicator comes on when the
headlight high beam is used.
EAU00057
Turn indicator light “ ”
This indicator flashes when the turn
switch is moved to the left or right.
EAU01154
Fuel indicator light “ ”
When the fuel level drops below
approximately 4.8 L, this light will
come on. When this light comes
on, fill the tank at the first opportuni-
ty. This light circuit can be checked
by the procedure on page 1-7.
If there is a shortcircuit or disconti-
nuity at the thermistor, the fuel indi-
cator light will flash 8 times and
then stay off for 3 seconds repeat-
edly.

1 - 10
INSTRUMENT AND CONTROL FUNCTIONS
1 1

1. Shift pedal
EAU00157
Shift pedal
This motorcycle is equipped with a con-
stant-mesh 6-speed transmission.
The shift pedal is located on the left
side of the engine and is used in com-
bination with the clutch when shifting.
1. Lever position adjusting dial
2. Arrow mark
a. Lever distance
EAU00161
Front brake lever
The front brake lever is located on the
right handlebar and is equipped with a
brake lever adjusting dial.
To activate the front brake, pull the le-
ver toward the handlebar.
To adjust the front brake lever position,
turn the brake lever adjusting dial while
pulling the lever forward. Make sure the
setting on the brake lever adjusting dial
is aligned with the arrow mark.
1 1
1. Rear brake pedalEAU00162
Rear brake pedal
The rear brake pedal is on the right
side of the motorcycle. Press down on
the brake pedal to apply the rear brake.
1. OpenEAU00172
Fuel tank cap
To open
Insert the key and turn it 1/4 turn clock-
wise. The lock will be released and the
cap can be opened.
To close
Push the tank cap into position with the
key inserted. To remove the key, turn it
counterclockwise to the original posi-
tion.
1 1NOTE:
This tank cap cannot be closed unless
the key is in the lock. The key cannot
be removed if the cap is not locked
properly.
EW000023
WARNING
Be sure the cap is properly installed
and locked in place before riding the
motorcycle.
1. Filler tube
2. Fuel level
EAU01183
Fuel
Make sure there is sufficient fuel in the
tank. Fill the fuel tank to the bottom of
the filler tube as shown in the illustra-
tion.
EW000130
WARNING
Do not overfill the fuel tank. Avoid
spilling fuel on the hot engine. Do
not fill the fuel tank above the bot-
tom of the filler tube or it may over-
flow when the fuel heats up later and
expands.

1 - 14
OPERATION AND IMPORTANT RIDING POINTS/
INCLUDED ACCESSORIES
EAU01128
Engine break-in
There is never a more important period
in the life of your motorcycle than the
period between zero and 1,600 km. For
this reason we ask that you carefully
read the following material. Because
the engine is brand new, you must not
put an excessive load on it for the first
1,600 km. The various parts in the en-
gine wear and polish themselves to the
correct operating clearances. During
this period, prolonged full throttle oper-
ation, or any condition which might re-
sult in excessive heating of the engine,
must be avoided.
EAU013290 ~ 1,000 km
Avoid operation above 5,500 r/min.
1,000 ~ 1,600 km
Avoid cruising speeds in excess of
7,000 r/min.
EC000052
CAUTION:
After 1,000 km of operation, be sure
to replace the engine oil and oil fil-
ter.
1,600 km and beyond
Proceed with normal riding.
EC000053
CAUTION:
lNever let engine speeds enter
the red zone.
lIf any engine trouble should oc-
cur during the break-in period,
consult a Yamaha dealer imme-
diately.
EAU00460
Parking
When parking the motorcycle, stop the
engine and remove the ignition key.
EW000058
WARNING
The exhaust system is hot. Park the
motorcycle in a place where pedes-
trians or children are not likely to
touch the motorcycle. Do not park
the motorcycle on a slope or soft
ground; the motorcycle may over-
turn.
INCLUDED ACCESSORIES
EAU01575
Tool kit
The tools provided in the owner’s tool
kit are to assist you in the performance
of periodic maintenance. However,
some other tools such as a torque
wrench are also necessary to perform
the maintenance correctly.
The service information included in this
manual is intended to provide you, the
owner, with the necessary information
for completing some of your own pre-
ventive maintenance and minor re-
pairs.
NOTE:
If you do not have necessary tools re-
quired during a service operation, take
your motorcycle to a Yamaha dealer
for service.
EW000063
WARNING
Modifications to this motorcycle not
approved by Yamaha may cause
loss of performance, and render it
unsafe for use. Consult a Yamaha
dealer before attempting any chang-
es.

1 - 17
MOTORCYCLE CARE AND STORAGE/
CONSUMER INFORMATION
WARNING
When using the starter motor to
crank the engine, remove the spark
plug wires, and ground them to pre-
vent sparking.
4. Remove the drive chain. Thor-
oughly clean the chain with kero-
sene and lubricate it. Reinstall the
chain or store it in a plastic bag
(tied to frame for safekeeping).
5. Lubricate all control cables.
6. Block up the frame to raise both
wheels off the ground.
7. Tie a plastic bag over the exhaust
pipe outlet to prevent moisture
from entering.
8. If strong in a humid or salt-air at-
mosphere, coat all exposed metal
surfaces with a light film of oil. Do
not apply oil to any rubber parts or
the seat cover.9. Remove the battery and charge it.
Store it in a dry place and re-
change it once a month. Do not
store the battery in an excessively
warm or cold place (less than 0°C
(30°F) or more than 30°C (90°F)).
NOTE:
Make any necessary repairs before
storing the motorcycle.
CONSUMER INFORMATION
EAU01040
Identification numbers record
Record the key identification number,
vehicle identification number and mod-
el label information in the spaces pro-
vided for assistance when ordering
spare parts from a Yamaha dealer or
for reference in case the vehicle is sto-
len.
1. KEY IDENTIFICATION
NUMBER:
2. VEHICLE IDENTIFICATION
NUMBER:
3. MODEL LABEL INFORMATION:
1. Key identification numberEAU01041
Key identification number
The key identification number is
stamped on the key tag. Record this
number in the space provided and use
it for reference when obtaining a new
key.
1. Vehicle identification numberEAU01043
Vehicle identification number
The vehicle identification number is
stamped into the steering head pipe.
Record this number in the space pro-
vided.
NOTE:
The vehicle identification number is
used to identify your motorcycle and
may be used to register your motorcy-
cle with the licensing authority in your
state.

7 - 56
CHAS
EB703002
Order Job/Part Q’ty Remarks
Disassembling the front fork legsRemove the parts in the order listed.
The following procedure applies to
both of the front fork legs.
1 Cap bolt/O-ring 1/1
2 Straight key 1
3 Washer 1
4 Damper adjusting rod 1
5 Nut 1
6 Spring seat 1
7Spacer 1
8Fork spring 1
9 Outer tube 1
0Dust seal 1
A Oil seal clip 1
B Oil seal 1
CWasher 1
FRONT FORK

7 - 58
CHAS
EB703100
REMOVING THE FRONT FORK LEGS
The following procedure applies to both of
the front fork legs.
1. Stand the motorcycle on a level surface.
WARNINGWARNING
Securely support the motorcycle so that
there is no danger of it falling over.
NOTE:
Place the motorcycle on a suitable stand
so that the front wheel is elevated.
2. Adjust:
• spring preload
NOTE:
Turn the adjusting bolt 1 in fully so that
it sits lightly. Refer to “ADJUSTING THE
FRONT FORK LEGS” in chapter 3.
1
1

3. Loosen:
• upper bracket pinch bolt 1
• cap bolt 2
(with the front fork cap bolt wrench)
• handlebar pinch bolts
• lower bracket pinch bolts
WARNINGWARNING
Before loosening the upper and lower
bracket pinch bolts and handlebar pinch
bolt, support the front fork leg.
4. Remove:
• front fork leg
Front fork cap bolt wrench:
90890-01472
1
1
2

2

EB703113
DISASSEMBLING THE FRONT FORK LEGS
The following procedure applies to both of
the front fork legs.
1. Remove:
• cap bolt 1
(from the damper rod assembly)
• straight key
• washer
• damper adjusting rod
4
51
2
3
FRONT FORK

7 - 59
CHAS
• nut 2
• spring seat 3
• spacer
t t t t t t t t t t t t t t t t t t t t t t t t t t t
a. Press down on the spacer with the
fork spring compressor 4.
b. Install the rod holder 5 between the
nut 2 and the spring seat 3.
NOTE:
Use the side of the rod holder that is
marked “A”.
c. Loosen the nut.
d. Remove the cap bolt, straight key,
washer and damper adjusting rod.
e. Remove the rod holder and fork
spring compressor.
WARNINGWARNING
The fork spring is compressed.
f. Remove the nut, spring seat and
spacer.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
Fork spring compressor
90890-01441
Rod holder
90890-01434
2. Drain:
• fork oil
NOTE:
Stroke the damper rod 1 several times
while draining the fork oil.
3. Remove:
• outer tube
(from inner tube)
4. Remove:
• dust seal
• oil seal clip 1
• oil seal
• washer
(with a flat-head screwdriver)
FRONT FORK