1999 YAMAHA YZF-R7 fuse

1 - 2
DESCRIPTION
DESCRIPTION
Left view
Right view
1. Front fork compression damping force adjusting screw
2. Front fork rebound damping force adjusting screw
3. Front fork spring preload adjusting bolt
4. Air filter
5. Starter (choke) “ “
6. Shift pedal
7. Rear shock absorber spring preload adjusting ring
8. Rear shock absorber compression damping force adjusting screw
9. Rear shock absorber rebound damping force adjusting screw
10. Fuses
11. Rear brake resorvoir
12. Rear brake pedal
13. Radiator cap and coolant reservoir tank cap
14. Engine oil filter
14
56
78
9
2,3
10
11
1213 14

1

ELECTRICAL SPECIFICATIONSSPEC
2 - 16
Electric starting system
System type Constant mesh ----
Starter motor
Model (manufacturer) SM-14 (MITSUBA) ----
Power output 0.6 kW ----
Armature coil resistance 0.0015 ~ 0.0025 W----
Brushes
Overall length 10 mm (0.40 in) 3.5 mm
(0.14 in)
Spring force 7.16 ~ 9.52 N
(730 ~ 971 gf, 25.8 ~ 34.3 oz)----
Commutator resistance 0.025 ~ 0.035 W----
Commutator diameter 28 mm (1.10 in) 27 mm
(1.06 in)
Mica undercut 0.7 mm (0.03 in) ----
Starter relay
Model (manufacturer) MS5F-631 (JIDECO) ----
Amperage 180 A ----
Coil resistance 4.18 ~ 4.62 W ----
Horn
Horn type Plain ----
Model (manufacturer) ´ quantity YF-12 (NIKKO) ´ 1 ----
Max. amperage 3 A ----
Turn signal relay
Relay type Full-transistor ----
Model (manufacturer) FE246BH (DENSO) ----
Self-cancelling device built-in No ----
Turn signal blinking frequency 75 ~ 95 cycles/min. ----
Wattage 21 W ´ 2 + 3.4 W ----
Oil level switch model (manufac-
turer)071380-0480 (DENSO) ----
Fuel pump relay model (manufac-
turer)G8R-30Y-J (OMRON) ----
Thermo switch model (manufac-
turer)5EB (NIPPON THERMOSTAT) ----
Fuses (amperage ´ quantity)
Main fuse 30 A ´ 1 ----
Headlight fuse 20 A ´ 1 ----
Signaling system fuse 20 A ´ 1 ----
EFI fuse 20 A ´ 1 ----
ECU fuse 7.5 A ´ 1 ----
Radiator fan fuse 7.5 A ´ 1 ----
Backup fuse (odometer) 7.5 A ´ 1 ---- Item Standard Limit

2 - 29
SPEC
JFuel tank breather hose
KCDI unit
LFall detection switch
MFuse box
NRelay unit
Align the portions of the main
switch lead and left handle-
bar switch lead marked with
white tape with the radiator
bracket at the frame.õFasten the starter cable and wire harness with a plastic band.
‚Fasten the oil level switch lead, speed sensor lead, sidestand
switch lead and stator coil assembly lead with a plastic band.
ëFasten the air filter breather hose, fuel tank overflow hose, clutch
hose and fuel tank breather hose with a plastic band.
ä20 mm (0.79 in)
ìRoute the sidestand switch lead behind the water pump breather
hose.
íRoute the oil level switch lead to the outside of the water pump
breather hose guide.
CABLE ROUTING

2 - 30
SPEC
1Ignition coil
2Throttle position sensor coupler
3Camshaft sensor
4Injector 1 coupler
5Starter motor
6Fuel tank overflow hose
7Fuel pump coupler
8Rectifier/regurator
9Battery
0Turn signal relayAECU
BFuse box
CFall detection switch
DStarter relay
EMain relay
FThrottle stop screw cable
GFuel tank breather hose
HAir filter case breather hose
IIntake air temperature sensor coupler
JInjector 2 sub-lead
CABLE ROUTING

2 - 31
SPEC
KPickup coil lead
LStator coil lead
MSpeed sensor lead
NSidestand switch lead
OOil level switch lead
PCoolant reservoir breather hose
QWire harness
RWire harness lead (to fall detection
switch coupler)
SWire harness lead (to fuse box)
TStarter motor leadUNeutral switch lead
VGround lead
WCoolant temperature sensor coupler
XThrottle cable
Route the wire harness in front of the ignition coils.
õBe sure that there is no slack in the tail/brake light lead
and rear turn signal leads below the rear fender panel.
‚Align the portions of the wire harness, ground lead and
starter motor lead marked with white tape with the lead
holder.
CABLE ROUTING

3 - 60
CHK
ADJCHECKING AND CHARGING THE BATTERY/
CHECKING THE FUSES
6. Install:
• battery
7. Connect:
• battery leads
(to the battery terminals)
ACHTUNG:CAUTION:
First, connect the positive lead 1, then
the negative lead 2.
8. Check:
• battery terminals
Dirt ® Clean with a wire brush.
Loose connection ® Connect properly.
9. Lubricate:
• battery terminals
10.Install:
• battery band 3
• rear cowling bracket 4
• rear cowling
Refer to “COWLINGS”.
EB305040
CHECKING THE FUSES
The following procedure applies to all of
the fuses.
ACHTUNG:CAUTION:
To avoid a short circuit, always set the
main switch to “OFF” when checking or
replacing a fuse.
1. Remove:
• rear cowling
Refer to “COWLINGS”.
2. Check:
• continuity
t t t t t t t t t t t t t t t t t t t t t t t t t t t
a. Connect the pocket tester to the fuse
and check the continuity.
NOTE:
Set the pocket tester selector to “W ´ 1”.
b. If the pocket tester indicates “¥”,
replace the fuse.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
Recommended lubricant
Dielectric grease
Pocket tester
90890-03112
2
2
1
1

3

3

4

4

3 - 61
CHK
ADJ
3. Replace:
• blown fuse
t t t t t t t t t t t t t t t t t t t t t t t t t t t
a. Set the main switch to “OFF”.
b. Install a new fuse of the correct
amperage.
c. Set the main switch to “ON” and ver-
ify if the electrical circuit is opera-
tional.
d. If the fuse immediately blows again,
check the electrical circuit.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
WARNINGWARNING
Never use a fuse with an amperage
other than that specified. Improvising or
using a fuse with the wrong amperage
rating may cause extensive damage to
the electrical system, cause the lighting
and ignition systems to malfunction
and could possibly cause a fire.
4. Install:
• rear cowling
Refer to “COWLINGS”.Item Amperage Q’ty
Main fuse 30 A 1
Headlight
fuse20 A 1
Signaling
system fuse20 A 1
Electronic
fuel injection
system fuse20 A 1
ECU fuse 7.5 A 1
Radiator
fan motor
fuse7.5 A 1
Backup fuse
(odometer)7.5 A 1
Reserve 30 A 1
Reserve 20 A 2
Reserve 7.5 A 2
CHECKING THE FUSES

8 - 1
–+ELEC

ELECTRICAL COMPONENTS
EB800000
ELECTRICAL
ELECTRICAL COMPONENTS
1
Wire harness
2
Main switch
3
Front brake light switch
4
Ignition coils
5
Clutch switch
6
Throttle position sensor
7
Intake air temperature sensor
8
Intake air pressure sensor
9
Atmospheric pressure sensor
0
Turn signal relay
A
Relay unit
B
ECU
C
CDI unit
D
Fuse box
E
Fall detection switch
F
Starter relay
G
Main fuse
H
Main relay
I
Battery
J
Rectifier/regulator
K
Rear brake light switch
L
Neutral switch
M
Speed sensor
N
Sidestand switch
O
Stator coil assembly
P
Oil level switch
Q
Pickup coil
R
Radiator fan
S
Horn
T
Coolant temperature
sender
U
Thermo switch
V
Camshaft sensor
8