1999 YAMAHA YZF-R7 check engine

3 - 2
CHK
ADJ

PERIODIC MAINTENANCE AND LUBRICATION
INTERVALS
*
Since these items require special tools, data and technical skills, they should be serviced by a
Yamaha dealer.
NOTE:

• The air filter element needs more frequent service if you are riding in unusually wet or
dusty areas.
• Hydraulic brake system
– Replace the brake fluid or clutch fluid after disassembling the master cylinder, caliper cyl-
inder or release cylinder.
– Check the brake fluid or clutch fluid level and add fluid as required.
– Replace the master cylinder, caliper cylinder and release cylinder oil seals every two
years.
– Replace the brake hoses and clutch hose every four years, or if cracked or damaged.
15
*
Chassis fasteners
• Make sure that all nuts, bolts and screws are properly
tightened.
• Tighten if necessary.
ÖÖ
16 Sidestand
• Check operation.
• Lubricate and repair if necessary.
ÖÖ
17
*
Sidestand switch
• Check operation.
• Replace if necessary.
ÖÖÖ
18
*
Front fork
• Check operation and for oil leakage.
• Correct accordingly.
ÖÖ
19
*
Rear shock
absorber assembly
• Check operation and shock absorber for oil leakage.
• Replace shock absorber assembly if necessary.
ÖÖ
20
*
Rear suspension
relay arm and con-
necting arm pivot-
ing points
• Check operation.
• Lubricate with lithium soap base grease every 24,000
km or 24 months (whichever comes first).
ÖÖ
21
*
Electronic fuel
injection system
• Check engine idling speed, synchronization and
starter operation.
• Adjust if necessary.
ÖÖÖ
22 Engine oil
• Check oil level and vehicle for oil leakage.
• Correct if necessary.
• Change. (Warm engine before draining.)
ÖÖÖ
23Engine oil filter
cartridge
• Replace.
ÖÖ
24
*
Cooling system
• Check coolant level and vehicle for coolant leakage.
• Correct if necessary.
• Change coolant every 24,000 km 24 months (which-
ever comes first).
ÖÖ
No. ITEM CHECKS AND MAINTENANCE JOBSINITIAL
1,000 km EVERY
6,000 km or
6 months
(whichever
comes first)12,000 km or
12 months
(whichever
comes first)
3

3 - 14
CHK
ADJADJUSTING THE VALVE CLEARANCE/
SYNCHRONIZING THE THROTTLE BODIES
g. Measure the valve clearance again.
h. If the valve clearance is still out of
specification, repeat all of the valve
clearance adjustment steps until the
specified clearance is obtained.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
8. Install:
• all removed parts
NOTE:
For installation, reverse the removal
procedure. Note the following points.
SYNCHRONIZING THE THROTTLE BODIES
NOTE:
Prior to synchronizing the throttle
bodies, the valve clearance and the
engine idling speed should be properly
adjusted and the ignition timing should
be checked.
1. Stand the motorcycle on a level surface.
NOTE:
Place the motorcycle on a suitable
stand.
2. Remove:
• fuel tank
Refer to “FUEL TANK AND AIR FIL-
TER”.
• bottom cowling
• front cowling
Refer to “COWLINGS”.
3. Remove:
• bolts 1
• copper washers
11

3 - 19
CHK
ADJADJUSTING THE THROTTLE CABLE FREE PLAY/
CHECKING THE SPARK PLUGS
Handlebar side
a. Loosen the locknut 4.
b. Turn the adjusting nut 5 in direction
c or d until the specified throttle
cable free play is obtained.
c. Tighten the locknut.
WARNINGWARNING
After adjusting the throttle cable free
play, start the engine and turn the han-
dlebars to the right and to the left to
ensure that this does not cause the
engine idling speed to change.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
Direction cThrottle cable free play
is increased.
Direction dThrottle cable free play
is decreased.
C C
d d
7
7
5
57
7
4
4
EB303040
CHECKING THE SPARK PLUGS
The following procedure applies to all of
the spark plugs.
1. Remove:
• fuel tank
• air filter case cover
Refer to “FUEL TANK AND AIR FIL-
TER”.
• air filter case
Refer to “ELECTRONIC FUEL INJEC-
TION” in chapter 6.
2. Disconnect:
• ignition coil couplers
3. Remove:
• ignition coils
• spark plug
ACHTUNG:CAUTION:
Before removing the spark plugs, blow
away any dirt accumulated in the spark
plug wells with compressed air to pre-
vent it from falling into the cylinders.
4. Check:
• spark plug type
Incorrect ® Change.
Spark plugs
Model (manufacturer)
R0256R-10 (NGK)

3 - 20
CHK
ADJCHECKING THE SPARK PLUGS/
MEASURING THE COMPRESSION PRESSURE
5. Check:
• electrodes 1
Damage/wear ® Replace the spark
plug.
• insulator 2
Abnormal color ® Replace the spark
plug.
Normal color is medium-to-light tan.
6. Clean:
• spark plug
(with a spark plug cleaner or wire
brush)
7. Measure:
• spark plug gap a
(with a wire gauge)
Out of specification ® Regap.
8. Install:
• spark plug
NOTE:
Before installing the spark plug, clean
the spark plug and gasket surface.
Spark plug gap
0.7 ~ 0.8 mm (0.028 ~ 0.031 in)
T R..13 Nm (1.3 m · kg, 9.4 ft · lb)
EB303060
MEASURING THE COMPRESSION
PRESSURE
The following procedure applies to all of
the cylinders.
NOTE:
Insufficient compression pressure will
result in a loss of performance.
1. Measure:
• valve clearance
Out of specification ® Adjust.
Refer to “ADJUSTING THE VALVE
CLEARANCE”.
2. Start the engine, warm it up for several
minutes, and then stop it.

3 - 22
CHK
ADJ
MEASURING THE COMPRESSION PRESSURE
WARNINGWARNING
To prevent sparking, ground all spark
plug leads before cranking the engine.
NOTE:
The difference in compression pressure
between cylinders should not exceed
100 kPa (1 kg/cm2, 14 psi).
c. If the compression pressure is above
the maximum specification, check the
cylinder head, valve surfaces, and
piston crown for carbon deposits.
Carbon deposits ® Eliminate.
d. If the compression pressure is below
the minimum specification, squirt a
few drops of oil into the cylinder and
measure again.
Refer to the following table.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
7. Install:
• spark plug Compression pressure
(with oil applied into the cylinder)
Reading Diagnosis
Higher than with-
out oilPiston wear or
damage ® Repair.
Same as without
oilPiston ring(-s),
valve(-s), cylinder
head gasket or
piston possibly
defective ®
Repair.
T R..13 Nm (1.3 m · kg, 9.4 ft · lb)

3 - 23
CHK
ADJ
CHECKING THE ENGINE OIL LEVEL
EB303070
CHECKING THE ENGINE OIL LEVEL
1. Stand the motorcycle on a level surface.
NOTE:
• Place the motorcycle on a suitable stand.
• Make sure that the motorcycle is
upright.
2. Start the engine, let it idle for several
minutes, and then stop it.
3. Check:
• engine oil level
The engine oil level should be between
the minimum level mark a and maxi-
mum level mark b.
Below the minimum level mark ® Add
the recommended engine oil to the
proper level.
Recommended oil
Refer to the chart for the
engine oil grade which is best
suited for certain atmo-
spheric temperatures.
API standard
SE or higher grade
(Non-Friction modified)
ACHTUNG:CAUTION:
• Engine oil also lubricates the clutch
and the wrong oil types or additives
could cause clutch slippage. There-
fore, do not add any chemical addi-
tives or use engine oils with a grade of
CD c or higher and do not use oils
labeled “ENERGY CONSERVING II” d
or higher.
• Do not allow foreign materials to
enter the crankcase.
4. Start the engine, warm it up for several
minutes, and then turn it off.
5. Check:
• engine oil level
NOTE:
Before checking the engine oil level,
wait a few minutes until the oil has set-
tled.

3 - 24
CHK
ADJ
CHANGING THE ENGINE OIL
EB303081
CHANGING THE ENGINE OIL
1. Remove:
• bottom cowling
• front cowling
Refer to “COWLINGS”.
2. Start the engine, warm it up for several
minutes, and then turn it off.
3. Place a container under the engine oil
drain bolt.
4. Remove:
• engine oil filler cap 1
• engine oil drain bolt 2
(along with the washer)
5. Drain:
• engine oil
(completely from the crankcase)
1
1

6. If the oil filter cartridge is also to be
replaced, perform the following proce-
dure.
t t t t t t t t t t t t t t t t t t t t t t t t t t t
a. Remove the oil filter cartridge 1 with
an oil filter wrench 2.
Oil filter wrench
90890-01426
b. Lubricate the O-ring 3 of the new oil
filter cartridge with a thin coat of
engine oil.
ACHTUNG:CAUTION:
Make sure that the O-ring 3 is posi-
tioned correctly in the groove of the oil
filter cartridge.
c. Tighten the new oil filter cartridge to
specification with an oil filter wrench.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
7. Check:
• engine oil drain bolt washer
Damage ® Replace.
8. Install:
• engine oil drain bolt
T R..
Oil filter cartridge
17 Nm (1.7 m • kg, 12 ft • lb)
T R..43 Nm (4.3 m · kg, 31 ft • lb)

3 - 25
CHK
ADJ
CHANGING THE ENGINE OIL
9. Fill:
• crankcase
(with the specified amount of the rec-
ommended engine oil)
10.Install:
• engine oil filler cap
11.Start the engine, warm it up for several
minutes, and then turn it off.
12.Check:
• engine
(for engine oil leaks)
13.Check:
• engine oil level
Refer to “CHECKING THE ENGINE OIL
LEVEL”.
Quantity
Total amount
3.6 L (3.2 lmp qt, 3.8 US qt)
Without oil filter cartridge
replacement
2.6 L (2.3 lmp qt, 2.7 US qt)
With oil filter cartridge
replacement
2.8 L (2.5 lmp qt, 3.0 US qt)
14.Check:
• engine oil pressure
t t t t t t t t t t t t t t t t t t t t t t t t t t t
a. Slightly loosen the oil gallery bolt 1.
b. Start the engine and keep it idling
until engine oil starts to seep from the
oil gallery bolt. If no engine oil comes
out after one minute, turn the engine
off so that it will not seize.
c. Check the engine oil passages, the oil
filter cartridge and the oil pump for
damage or leakage. Refer to “OIL
PAN AND OIL PUMP” in chapter 4.
d. Start the engine after solving the
problem(-s) and check the engine oil
pressure again.
e. Tighten the oil gallery bolt to
specification.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
T R..
Oil gallery bolt
20 Nm (2.0 m • kg, 14 ft • lb)
1
1