1999 TOYOTA AVENSIS engine oil

I04818
SPEEDOMETER
TACHOMETER
WATER TEMP.
FUEL
OIL LEVEL
ODO / TRIP
METER
OUTSIDE TEMP.
CLOCK
RHEOSTATLCD
DISPLAY
LCD
DISPLAY S
T
W
FA18
B7
B20 A5
A15
A3
A6
A7
A8
A12
A11
A19
A10
A9
B11
B24
B5
A22
B4
A23
B14
A23
A25
B16
B14
B21
A22
A14VOLTAGE
STABILIZER
B17
B22
B9
B26
A24 Brake Warning
Fuel filter Warning
Discharge Waring
Economy Indicator
Turbo / Glow Plug Indicator
Glow Plug Indicator
ABS Warning
Low Oil Pressure Warning
Check Engine Warning
O / D OFF Indicator
ECT SNOW Indicator
ECT PWR Indicator
Rear Fog Light Indicator
High Beam Indicator
Right Turn Indicator
Left Turn Indicator
Open Door Warning
SRS Warning
Front Fog light Indicator A1
B15
B18A26
B2
A17
B1
B13
B6
B3 B19
BE–4
– BODY ELECTRICALCOMBINATION METER

No.
AGround (Power)
Tacho Pick–UP Sensor
EFI ECU (3S–FE, 2C–TE Engine)
EGR (2C–T Engine)
Vehicle Speed Sensor
EFI ECU
Water Temperature Sender Gauge (2C–T Engine)
Ground (Engine)
Ground
Outside Temperature Sender Gauge
Ground (Fuel)
Fuel Sender Gauge
Ground (Power)
Ground (Speed)
Turn Signal Switch (Right)
Other Parts
Oil Level Warning Switch
O/D OFF Switch
ECT ECU (Gasoline Engine)
Fuel Filter Warning Switch (Diesel Engine)
Glow Plug Timer (Diesel Engine)
EFI ECU (Gasoline Engine)
ECT Pattern Select Switch
ABS ECU
Rear Fog Light Switch 1
3
5
6
7
8
9
10
11
12
14
15
17
18
19
21
22
23
24
25
26Wire Harness Side
1
2
3
4
5
6
7
9
11
13
14
15
16
17
18
19
20
22
24
26Turn Signal Switch (Left)
H–LP Fuse
Front Fog Light Switch
Alternator L Terminal
Brake Fluid Level Warning Switch
Parking Brake Switch
ECU+B Fuse
Taillight Relay
GAUGE Fuse
Ground (Signal)
DOOR Fuse
EFI ECU (Gasoline Engine)
EGR ECU (Diesel Engine)
Headlight Dimmer Switch
Low Oil Pressure Warning Switch
IGN Fuse
Door Courtesy Switch
Airbag ECU
Taillight Relay
GAUGE Fuse
Ground (Signal)
DOOR Fuse
B
– BODY ELECTRICALCOMBINATION METER
BE–5

I01275
Ignition
Switch
BatterySender
Gauge Receiver
Gauge
I01276
Ignition
Switch
BatteryReceiver
Gauge
Test Bulb
(3.4 W)
I01277
Battery Ignition
SwitchWarning Light
Wire Harness Side
1
– BODY ELECTRICALCOMBINATION METER
BE–7
(b) Compare the tester and tachometer indications.
DC 13.5 V 25
C at (77
F)
Standard indicationAllowable range
700630 – 770
1,000900 – 1,100
2,0001,850 – 2,150
3,0002,800 – 3,200
4,0003,800 – 4,200
5,0004,800 – 5,200
6,0005,750 – 6,250
7,0006,700 – 7,300
4. INSPECT ENGINE COOLANT TEMPERATURE RE-
CEIVER GAUGE OPERATION
(a) Disconnect the connector from the sender gauge.
(b) Turn the ignition switch ON and check that the receiver
gauge needle indicates COOL.
(c) Ground terminal on the wire harness side connector
through a 3.4 W test bulb.
(d) Turn the ignition switch ON, and check that the bulb lights
up and the receiver gauge needle moves to the hot side.
If operation is as specified, replace the sender gauge.
Then recheck the system.
If operation is not as specified, measure the receiver gauge re-
sistance.
5. INSPECT LOW OIL PRESSURE WARNING LIGHT
(a) Disconnect the connector from the warning switch and
ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON and check that the warning
light lights up.
If the warning light does not light up, test the bulb.

I01278
BE–8
– BODY ELECTRICALCOMBINATION METER
6. INSPECT LOW OIL PRESSURE SWITCH CONTINUITY
(a) Disconnect the connector from the switch.
(b) Check that continuity exists between terminal and ground
with the engine stopped.
(c) Check that no continuity exists between terminal and
ground with the engine running.
HINT:
Oil pressure should be over 24.5 kPa (0.25 kgf/cm
2, 3.55 psi).
If operation is not as specified, replace the switch.

AC2A9–01
I12482
3
I12483
1 2
– AIR CONDITIONINGCOMPRESSOR AND MAGNETIC CLUTCH (1CD–FTV)
AC–25
COMPRESSOR AND MAGNETIC
CLUTCH (1CD–FTV)
ON–VEHICLE INSPECTION
1. MAKE THESE VISUAL CHECKS:
(a) Leakage of grease from the clutch bearing
(b) Signs of oil on the pressure plate or rotor
2. INSPECT MAGNETIC CLUTCH BEARING FOR NOISE
(a) Start the engine.
(b) Check for abnormal noise from the compressor when the
A/C switch is OFF.
If abnormal noise is being emitted, replace the magnetic clutch.
3. INSPECT MAGNETIC CLUTCH OPERATION
(a) Disconnect the connector.
(b) Connect the positive (+) lead from the battery to the termi-
nal 3 on the magnetic clutch connector and the negative
(–) lead to the body ground.
(c) Check that the magnetic clutch is energized.
If operation is not as specified, replace the magnetic clutch.
4. INSPECT COMPRESSOR LOCK SENSOR RESIS-
TANCE
(a) Disconnect the connector.
(b) Measure resistance between terminals 1 and 2.
Standard resistance: 65 – 125 Ω at 20C (68F)

AC2AC–01
I12469
I12494
AC–28
– AIR CONDITIONINGCOMPRESSOR AND MAGNETIC CLUTCH (1CD–FTV)
INSTALLATION
1. INSTALL COMPRESSOR
(a) Install the compressor with the 3 bolts.
Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(b) Connect the connector.
2. CONNECT DISCHARGE AND SUCTION HOSES
Connect the both hoses with the 2 bolts.
Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)
CAUTION:
Hoses should be connected immediately after the caps
have removed.
HINT:
Lubricate 2 new O–rings with compressor oil and install the
hoses.
3. INSTALL RESERVOIR TANK
(a) Connect the reservoir tank with the 2 bolts.
(b) Connect the lower hose.
(c) Install the upper hose.
4. REFILL ENGINE COOLANT
5. INSTALL AND CHECK DRIVE BELT
(See page AC–3)
6. INSTALL ENGINE UNDER COVER RH
7. CONNECT NEGATIVE (–) TERMINAL CABLE TO BAT-
TERY
8. EVACUATE AIR IN REFRIGERATION SYSTEM AND
CHARGE WITH REFRIGERANT
Specified amount: 450
50 g (15.87
1.76 oz.)
9. INSPECT FOR LEAKAGE OF REFRIGERANT
Using a gas leak detector, check the tightening torque at the
joints.
10. INSPECT A/C OPERATION