1999 SUZUKI GRAND VITARA Arnes

YH4
GRAND
VITARA
9-20 BODY SERVICE
1. Sealing cover
2. Adhesive
INSTALLATION
Reverse removal procedure to install back door / rear gate noting
following points.

Secure wiring harness.

Secure back door / rear gate sealing cover.
NOTE:
Use adhesive to seal sealing cover to back door / rear gate.

Adjust back door / rear gate latch striker position by referring
ªBACK DOOR LOCK ASSEMBLY INSTALLATIONº so that back
door / rear gate is positioned correctly.

Adjust back door / rear gate cushion so that back door / rear gate
contacts body when closed.

YH4
GRAND
VITARA
1. (a)
1. (a)
1
11
Tightening Torque
(a): 23 N.m (2.3 kg-m, 17.0 lb-ft)
1. Bolt
BODY SERVICE 9-33
INSTRUMENTATION AND DRIVER INFORMATION
INSTRUMENT PANEL
WARNING:
See WARNING at the beginning of this section.
REMOVAL
1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to ªDisabling Air Bag Systemº in
Section 10B.
3) Remove console box.
4) Remove glove box and column hole cover.
5) Disconnect wires and cables from heater unit and blower motor
assembly.
6) Remove steering column assembly. Refer to Section 3C1.
7) Disconnect speedometer connector and remove speedometer
assembly. If equipped with air bag, disconnect wire coupler at
SDM and air bag ground terminal for air bag.
8) Remove engine hood opener.
9) Disconnect couplers which need to be disconnected for removal
for instrument panel.
10) Remove instrument panel mounting screws.
11) Remove instrument panel mounting bolt.
12) Remove instrument panel.
CAUTION:
For vehicle with Air Bag, instrument panel could not be re-
moved with SDM coupler connected and ground terminal
installed.
Use care not to damage Air Bag harness.
INSTALLATION
1) Install instrument panel by reversing removal procedure, noting
the following items.

When installing each part, be careful not to catch any cable or
wiring harness.

When installing steering column assembly, refer to ªAIR BAG
STEERING COLUMN INSTALLATIONº in Section 3C1.
2) Adjust control cables. (Refer to Section 1A ªHEATER CON-
TROL CABLESº.)
3) Enable air bag system. Refer to ªEnabling Air Bag Systemº in
Section 10B.

YH4
GRAND
VITARA
BODY SERVICE 9-73
5
46
4. Assistant grip
5. Rear room light
6. Inner trim
1. Roof harness
2. Rear washer hose
3. Adhesive tape
Front 1. Room light
2. Sunshade assembly
3. Spot light
IWATA
CAMI
HEAD LINING
REMOVAL
1) Remove spot light and sliding roof switch (if equipped).
2) Remove sunshade assembly.
3) Remove room light and spacer.
4) Remove assistant grips.
5) Remove inner trims covering head lining and door opening trim.
6) Remove rear speaker cover (if equipped).
7) Disconnect rear washer hose and roof harness from body.
8) Remove head lining.
NOTE:
Adhesive double coated tape is used to attach rear part of
head lining. Detach head lining from roof after removing all
above parts.
INSTALLATION
1) Set roof harness and washer hose to head lining with tape.
2) Clean roof where adhesive tape of head lining will be attached.
3) Peel off release liner of adhesive tape on head lining and install
it to body.
4) Install assistant grips a, b, c and d in that order.

YH4
GRAND
VITARA
BODY SERVICE 9-75
1. Canvas top
2. Rear topbow
3. Side body garnish
4. Luggage mat end garnish
5. Assistant grip
6. Sunshade assembly
7. Sunshade hook
8. Front topbow lock
9. Canvas top snap
10. Front seat belt
11. Front pillar trim
12. Rear side inner lower trim
13. Rear side inner upper trim
14. Room light connector
15. Room light harness clamp
16. Roof trim
17. Left-front seat belt
ROOF TRIM (2 DOOR MODEL)
REMOVAL
1) Remove canvas top.
2) Remove rear topbow.
3) Remove side body garnishes.
4) Remove luggage mat end garnish.
5) Remove assistant grips.
6) Remove sunshade assemblies.
7) Remove sunshade hooks.
8) Remove front topbow locks.
9) Remove canvas top snaps.
10) Remove front seat belts.
11) Remove front pillar trims.
12) Remove rear side inner lower trims.
13) Remove rear side inner upper trims.
14) Disconnect room light connector and remove room light har-
ness clamp.
15) Remove roof trim.
CAUTION:
Be very careful not to separate roof trim consists of 4
components when removing. If disassemble it, it could
not be assembled to original unit.

YH4
GRAND
VITARA
9-76 BODY SERVICE
1. Roof trim
2. Room light
3. Room light lens4. Clip
5. Screw
6. Room light harness
7. Marking tape
1. Seat belt
INSTALLATION
1) Set room light and clip to roof trim.
2) Set room light harness to roof trim with marking tape.
3) Reverse removal sequence to install roof trim.
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.3 lb-ft)

YH4
GRAND
VITARA
10B-4 AIR BAG SYSTEM
1. Air bag harness
2. ªAIR BAGº fuse box
3. ªAIR BAGº monitor coupler
4. DLC
5. Contact coil assembly
6. Driver air bag (inflator) module
7. Passenger air bag (inflator) module
8. SDM
9. Seat belt pretensioner
(retractor assembly) (if equipped)
10. Pretensioner harness (if equipped)
11. Ground for air bag systemCONNECTOR ªAº
CONNECTOR ªCº, ªDº
CONNECTOR ªBº
CONNECTOR ªEº
CONNECTOR ªHº
CONNECTOR ªFº
CONNECTOR ªGº
SYSTEM COMPONENTS AND WIRING LOCATION VIEW AND CONNECTORS

YH4
GRAND
VITARA
WIRE HARNESS COLOR
B : Black
B/W : Black/White
Bl : Blue
Bl/B : Blue/Black
Bl/R : Blue/Red
Br : BrownG : Green
Gr : Gray
G/R : Green/Red
Lg : Lightgreen
P : Pink
V : VioletY : Yellow
Y / G : Yellow/Green
Y/R : Yellow/Red
W : White
W/B : White/Black
1. From main fuse
2. Ignition switch
3. ªIG
.COIL METERº fuse in J/B
4. ªAIR BAGº warning lamp in combination meter
5. ªAIR BAGº fuse in ªAIR BAGº fuse box
6. Connection detection pin
7. To ECM (or PCM), ICM (if equipped) and ABS
controller (if equipped)
8. To data link connector (DLC)
9. ªAIR BAGº monitor coupler
10. SDM
11. Contact coil assembly
12. Driver air bag (inflator) module
13. Driver seat belt pretensioner (if equipped)
14. Passenger air bag (inflator) module
15. Passenger seat belt pretensioner (if equipped)
16. Pretensioner harness (if equipped)
17. Ground for air bag system
TERMINAL
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A13 A11
A12
A14
A15
A16
Passenger air bag (inflator) moduleLow
High
CIRCUIT
Data link connector (DLC)
Low
High
Low
High
Low
High ªAIR BAGº warning lamp
Driver air bag (inflator) module
Diagnosis switch
±±±±±±±±±
Ground
Passenger pretensioner
Driver pretensioner
Ignition switch (power source)±±±±±±±±±
±±±±±±±±±
CONNECTOR ªAº (SDM connector) TERMINAL ARRANGEMENT OF SDM
(VIEWED FROM HARNESS SIDE)
L1
L2Connection detection pin
: Shorting bar
: Air bag harness
ªAº
ªHº : Connector
AIR BAG SYSTEM 10B-5
SYSTEM WIRING DIAGRAM

YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-7
Special Tool (Air Bag Driver/Passenger Load Tool)
(B): 09932-75010
This tool is used only when called for in this section. It is used as
a diagnostic aid and safety device to prevent inadvertent air bag (in-
flator) module deployment and seat belt pretensioner activation.
The load tool has three connectors attached to its case are electri-
cally functional and serve as resistive load substitutions.
No more than two connectors are used at any time.
One of connectors (ªAº: BASE OF COLUMN) is used to substitute
the load of the driver air bag (inflator) module and the contact coil
assembly when it is connected at the base of the column to the air
bag wire harness.
Another connector (ªBº: STEERING WHEEL) is used to substitute
the load of followings.

Driver air bag (inflator) module when it is connected at the top of
the column to the contact coil assembly.

Passenger air bag (inflator) module when it is connected to the
air bag harness connector for passenger air bag (inflator) module.

Driver and passenger seat belt pretensioner when it is connected
to air bag harness connector for driver and passenger seat belt
pretensioner.
The third connector (ªCº: PASSENGER INFLATOR) is not used.
By substituting the resistance of the load tool when called for, a de-
termination can be made as to whether an inflator circuit compo-
nent is causing system malfunction and which component is caus-
ing the malfunction.
The load tool should be used only when specifically called for in the
diagnostic procedures.