1999 SUZUKI GRAND VITARA bearing

YH4
GRAND
VITARA
(a)
(a)
1. Bolt
2. Washer
3. Lateral rod
1. Nut
1
3E-10 REAR SUSPENSION
LATERAL ROD
REMOVAL
1) Hoist vehicle.
2) Remove lateral rod mounting bolts.
3) Remove lateral rod.
INSTALLATION
1) Install lateral rod to rear axle, and vehicle body.
2) Lower hoist.
3) Tighten lateral rod mounting bolts to specified torque.
Tightening Torque
(a): 90 N
.m (9.0 kg-m, 65.0 lb-ft)
REAR AXLE SHAFT AND WHEEL BEARING
REMOVAL
1) Remove rear brake drum. For details, refer to REAR BRAKE
DRUM REMOVAL in SECTION 5C.
2) Drain gear oil from rear axle housing by loosening drain plug.
3) Remove rear wheel bearing retainer nuts from axle housing.

YH4
GRAND
VITARA
1. Bearing retainer
2. Parking brake shoe
lever
3. Clearance1. Wheel speed sensor
1
L
REAR SUSPENSION 3E-11
4) Remove wheel speed sensor from rear axle housing (if
equipped with ABS).
CAUTION:

Do not pull wire harness or twist more than necessary
when removing rear wheel speed sensor.

Do not cause damage to surface of rear wheel speed
sensor or pole piece and do not allow dust, etc. to enter
its installation hole.
5) Check to ensure that there is clearance between rear wheel
bearing retainer and parking brake shoe lever. If no clearance
is found, loosen cable locking nut further to obtain clearance.
6) Using special tools (B) & (C) indicated below, draw out axle
shaft.
NOTE:
Use care not to pull brake back plate along with shaft.
CAUTION:
Pull out axle shaft using care so that upper and lower
brake struts and parking cable are not caught.
Special Tool
(C): 09943-35512
(B): 09942-15510
7) Rear axle shaft that was drawn out.
Shaft length ªLº:
Left side: 711.5 mm (28.0 in.)
Right side: 757.5 mm (29.8 in.)
8) If equipped with ABS, in order to remove sensor rotor from re-
tainer ring, grind with a grinder one part of the sensor rotor as
illustrated till it becomes thin.

YH4
GRAND
VITARA
1. Axle shaft
2. Wheel bearing
3. Press
1. Stud bolt
2. Hydraulic press
1. Rear wheel bearing
retainer ring
2. Grind with a grinder
3. Rear axle
3E-12 REAR SUSPENSION
9) Break with a chisel the thin ground sensor rotor, and it can be
removed (if equipped with ABS).
10) In order to remove the retainer ring from the shaft, grind with
a grinder two parts of the bearing retainer ring as illustrated till
it becomes thin.
CAUTION:
Be careful not to grind too far not to damage the shaft.
11) Break with a chisel the thin ground retainer ring, and it can be
removed.
12) Remove bearing from shaft by using hydraulic press.
13) Remove bearing retainer.
14) Remove stud bolt(s) by using hydraulic press.

YH4
GRAND
VITARA
[B]
1
2
[A]
1. Bearing retainer
2. Oil seal
3. Wheel side
4. Differential side
1. Stud bolt
2. Nut
3. Washer
4. Flange of axle shaft
1. Axle shaft
2. Bearing retainer
[A]: Vehicle without ABS
[B]: Vehicle with ABS
1. Bearing
2. Retainer ring
REAR SUSPENSION 3E-13
INSTALLATION
Install removed parts in reverse order of removal procedure, noting
the following.
1) Apply grease to oil seal lip as shown and install it to axle shaft.
NOTE:
Amount of grease applied to hollow in oil seal should be
more than 60% of its vacant space.
ªAº: Grease 99000-25010
2) Aligning serrations between new stud bolt(s) and flange, install
new stud bolt(s) by tightening nut as shown.
3) Install bearing retainer to shaft.
4) Press-fit wheel bearing and retainer ring as shown.
NOTE:

Use care not to cause any damage to outside of retainer
ring.

Refer to figure so that wheel bearing is installed in proper
direction.

YH4
GRAND
VITARA
1. Sensor rotor
1. Axle housing
1. Bearing retainer
(b)
3E-14 REAR SUSPENSION
5) For vehicle with ABS, press-fit new sensor rotor as shown.
NOTE:
Use care not to cause any damage to outside of retainer
ring.
6) Apply grease to axle shaft inner oil seal lip as shown.
ªAº: Grease 99000-25010
7) Apply sealant to mating surface of bearing retainer with brake
back plate.
NOTE:
Make sure to remove old sealant before applying it anew.
ªBº: Sealant 99000-31110
8) Install rear axle shaft to rear axle housing and tighten bearing
retainer nuts to specified torque.
NOTE:
When installing rear axle shaft, be careful not to cause
damage to oil seal lip in axle housing.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
9) Tighten wheel speed sensor bolt to specified torque (if
equipped with ABS).
Tightening Torque
(b): 21 N
.m (2.1 kg-m, 15.5 lb-ft)
10) Refill rear axle (differential) housing with new specified gear oil.
Refer to SECTION 7F for refill.
11) Install brake drum. (For details, refer to BRAKE DRUM
INSTALLATION in SECTION 5.)

YH4
GRAND
VITARA
1. Brake pipe flare nut
2. Brake pipe
3. Brake back plate
1. Bearing retainer
2. Parking brake shoe
lever
3. Clearance1. Nut 1. Wheel speed sensor
2. Wheel speed sensor coupler
3. Wheel speed sensor harness clamp
4. Wheel speed sensor harness
3E-16 REAR SUSPENSION
REAR AXLE HOUSING
REMOVAL
1) Drain differential gear oil.
Carry out steps 2) to 7) and 15) to 18) on both right and left
wheels.
Note that left wheel and its related parts are used in illustrations
in this section.
2) Remove rear brake drum. (Refer to steps 1) to 5) of BRAKE
DRUM REMOVAL.)
3) Disconnect brake pipe from wheel cylinder. With right side wheel
cylinder, disconnect 2 brake pipes.
4) For vehicle with ABS, disconnect wheel speed sensor coupler
and remove wheel speed sensor with its harness.
5) Remove rear wheel bearing retainer nuts from rear axle hous-
ing.
6) Check to ensure that there is clearance between rear wheel
bearing retainer and parking brake shoe lever. If no clearance
is found, loosen cable locking nut further to obtain clearance.

YH4
GRAND
VITARA
3. Container 1. Plug cap
2. Vinyl tube
1. Bearing retainer
(e)
(f)
(g)
REAR SUSPENSION 3E-21
16) Apply sealant to mating surface of bearing retainer with brake
back plate.
NOTE:
Make sure to remove old sealant before applying it anew.
ªBº: Sealant 99000-31110
17) Install rear axle shaft to rear axle housing and tighten bearing
retainer nuts to specified torque.
NOTE:
When installing rear axle shaft, be careful not to cause
damage to oil seal lip in axle housing.
Tightening Torque
(e): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
18) For vehicle with ABS, tighten wheel speed sensor bolt to speci-
fied torque.
Tightening Torque
(f): 21 N
.m (2.1 kg-m, 15.5 lb-ft)
19) Connect brake pipes to wheel cylinders (right & left) and tighten
brake pipe flare nuts to specified torque.
Tightening Torque
(g): 16 N
.m (1.6 kg-m, 11.5 lb-ft)
20) Install brake drum (right & left). For details, refer to SECTION
5C ªBRAKE DRUM INSTALLATIONº.
21) Refill differential gear housing with new specified gear oil. Re-
fer to ªON-VEHICLE SERVICEº in SECTION 7F for refill.
22) Fill reservoir with brake fluid and bleed brake system.(For
bleeding operation, see SECTION 5.)

YH4
GRAND
VITARA
REAR SUSPENSION 3E-23
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mKg-mlb-ft
Shock absorber lock nut292.921.0
Shock absorber nut292.921.0
Shock absorber lower nut858.561.5
Lower rod bolt and nut
Upper rod bolt and nut909.065.0
Lateral rod bolt
Differential carrier nut555.540.0
Propeller shaft nut505.036.5
Brake pipe flare nut161.611.5
Bearing retainer nut232.317.0
Differentiation gear oilFiller plug505.036.5g
filler & drain plugDrain plug272.716.0
Wheel nut10010.072.5
REQUIRED SERVICE MATERIALS
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUZUKI SUPER GREASE A
(99000-25010)Oil seal lip
Brake fluidDOT 3Brake reservoir tank
Sealant
SUZUKI BOND NO. 1215
(99000-31110)
Joint seam of axle and brake back
plate

Joint seam of bearing retainer and
brake back plate

Joint seam of differential carrier and
axle housing

Drain plug

Mating surface of oil seal and axle
housing
Gear oilFor gear oil information, refer to
SECTION 7F of this manualDifferential gear
(Refer axle housing.)