1999 SUZUKI GRAND VITARA Engine bolt torque

YH4
GRAND
VITARA
7C1-14 CLUTCH
09917-58010 (G16 engine)
09923-73210
(J20 and H25 engines)
Bearing remover09923-36330 (G16 engine)
09923-36320
(J20 and H25 engines)
Clutch center guide09924-17810
Flywheel holder09925-98210
Input shaft bearing installer
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN.mkg-mlb-ft
Flare nut161.611.5
Master cylinder nut131.39.5
Lock nut101.07.5
Flywheel boltsG16 engine787.856.5Flywheel boltsJ20 and H25 engines707.050.5
Clutch cover bolts232.316.5
Operating cylinder bolt505.036.5
Clutch hose union bolt232.316.5
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Lithium grease
SUZUKI SUPER GREASE A
(99000-25010)
Clutch master cylinder clevis pin.

Release fork.

Push rod tip of operating cylinder.
SUZUKI SUPER GREASE I
(99000-25210)Input shaft spline front end.
Clutch fluid
(Brake fluid)DOT3 or SAE J1703

Clutch reservoir.

Clutch master cylinder.

Clutch operating cylinder.
SealantSUZUKI BOND No.1215
(99000-31110)Flywheel bolts
SPECIAL TOOLS

YH4
GRAND
VITARA
1. Speed sensor assembly
2. Transfer
7D-4 TRANSFER
SPEEDOMETER DRIVEN GEAR
REMOVAL
1) Lift up vehicle horizontally or rear up.
2) Disconnect speed sensor coupler at transfer case.
3) Remove bolt and take off speed sensor from transfer.
INSTALLATION
1) Make sure that O-ring and speed sensor have not been dam-
aged.
2) Inspect speedometer driven gear for abnormal wear of gear
teeth or bend of shaft portion and replace it if necessary.
3) Make sure its smooth rotation.
4) Install speed sensor assembly to transfer and connect coupler
as it was.
Tightening Torque
(a): 6 N
.m (0.6 kg-m, 4.5 lb-ft)
ENGINE REAR MOUNTING
Refer to ªON-VEHICLE SERVICEº of Section 7A.

YH4
GRAND
VITARA
1. Bolt
2. Transfer assembly
1. Bolt
2. Engine rear mounting3. Transfer assembly
1. Bolt
2. Transfer assembly
3. Transmission jack
7D-6 TRANSFER
IN CABIN
Remove gear shift lever case and then remove transfer center case
bolt.
ON LIFT
1) Remove transfer mounting (engine rear mounting) by removing
bolts.
2) Apply transmission jack to transfer to support it.
3) Remove couplers for 4WD / 4WD-LOW switches lead.
4) Remove transfer front case bolts.
5) With transfer assembly supported with transmission jack, slide
it rearward and when it is apart from transmission, lower it.
REMOUNTING
For remounting, reverse dismounting procedure described above,
noting following.

Be sure to use specified torque for tightening.

Clamp wiring and breather hose securely.

Clamp shift lever boot securely.

Fill specified gear oil by specified amount.

Connect battery and check for function.

YH4
GRAND
VITARA
TRANSFER 7D-7
09940-53111
Bearing installer
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in FOREWORD of this manual.
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN.mkg-mlb-ft
Oil filler / level and drain plugs232.317.0
Engine rear mounting bolts505.036.5
Universal joint flange bolts505.036.5
Speed sensor bolt60.64.5
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUZUKI SUPER GREASE A
(99000-25010)

Oil seal lips and O-rings.

Splines of propeller shaft.

Select return system.

Shift control lever.
SPECIAL TOOL

YH4
GRAND
VITARA
1. (a)
1. (a)
1
11
Tightening Torque
(a): 23 N.m (2.3 kg-m, 17.0 lb-ft)
1. Bolt
BODY SERVICE 9-33
INSTRUMENTATION AND DRIVER INFORMATION
INSTRUMENT PANEL
WARNING:
See WARNING at the beginning of this section.
REMOVAL
1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to ªDisabling Air Bag Systemº in
Section 10B.
3) Remove console box.
4) Remove glove box and column hole cover.
5) Disconnect wires and cables from heater unit and blower motor
assembly.
6) Remove steering column assembly. Refer to Section 3C1.
7) Disconnect speedometer connector and remove speedometer
assembly. If equipped with air bag, disconnect wire coupler at
SDM and air bag ground terminal for air bag.
8) Remove engine hood opener.
9) Disconnect couplers which need to be disconnected for removal
for instrument panel.
10) Remove instrument panel mounting screws.
11) Remove instrument panel mounting bolt.
12) Remove instrument panel.
CAUTION:
For vehicle with Air Bag, instrument panel could not be re-
moved with SDM coupler connected and ground terminal
installed.
Use care not to damage Air Bag harness.
INSTALLATION
1) Install instrument panel by reversing removal procedure, noting
the following items.

When installing each part, be careful not to catch any cable or
wiring harness.

When installing steering column assembly, refer to ªAIR BAG
STEERING COLUMN INSTALLATIONº in Section 3C1.
2) Adjust control cables. (Refer to Section 1A ªHEATER CON-
TROL CABLESº.)
3) Enable air bag system. Refer to ªEnabling Air Bag Systemº in
Section 10B.