1999 SUZUKI GRAND VITARA ECU

YH4
GRAND
VITARA
1. LSPV
2. LSPV lever
3. Spring
4. LSPV stay
5. Brake flare nut
[A]: Type A
[B]: Type B
1. Plunger
2. Lip seal
3. LSPV lever
4. Sensor spring
5. From master cylinder
primary chamber
(Rear wheel brake)
6. From master cylinder
secondary chamber
(Front wheel brake)
7. To rear wheel brake
8. Pin
9. Bolt hole
[A] [B]
44
BRAKES PIPE / HOSE / MASTER CYLINDER 5A-3
LSPV (Load Sensing Proportioning Valve) ASSEMBLY (if equipped)
As shown in figure below, LSPV is included within the brake circuit which connects the master cylinder and the rear
wheel brake. It controls the hydraulic pressure applied to the rear wheel brake according to the loaded state of the
vehicle (or weight of the load), whereby preventing the rear wheels from getting locked prematurely.
Also, it releases the above described control over the hydraulic pressure applied to the rear wheel brake, should
any failure occur in the hydraulic circuit of the front wheel brake so that the hydraulic pressure produced in the mas-
ter cylinder is applied to the rear wheel brake directly to operate it.
CONSTITUTION
The LSPV components are grouped into three sections as follows.
ªAº: Sensor section
The main parts in this section are a lever and a spring which senses variation in the vehicle height as affected
by the loaded condition and converts it into the load.
ªBº: Hydraulic pressure control section
Included in this section are a stepped plunger and valve mechanism to execute proportional control.
ªCº: Fail-safe section
The main parts in this section are a chamber which draws in the hydraulic pressure from the front wheel brake
system and a fail-safe piston which releases the valve mechanism in the control section connected to the rear
wheel brake, should any failure occur in the front wheel brake system.

YH4
GRAND
VITARA
5B-4 FRONT BRAKE
1. Wheel nut
2. Washer
(or spacer)
ªAº: Apply grease
Brake Disc
Before this inspection, brake pads must be removed.
Check disc surface for scratches in wearing parts. Scratches on
disc surface noticed at the time of specified inspection or replace-
ment are normal and disc is not defective unless they are serious.
But when there are deep scratches or scratches all over disc sur-
face, replace it. When only one side is scratched, polish and correct
that side.
Disc thickness ªaº
Standard: 22 mm (0.866 in.) For SUMITOMO ELECTRIC. . . . .
brake caliper
17 mm (0.670 in.) For TOKICO brake caliper. . . . .
Service limit: 20 mm (0.787 in.) For SUMITOMO ELECTRIC. .
brake caliper
15 mm (0.590 in.) For TOKICO brake caliper. .
Use wheel nuts and suitable plain washers to hold the disc securely
against the hub, then mount a dial indicator as shown and measure
the runout at 25 mm (0.98 in.) from the outer edge of the disc.
Limit on disc deflection: 0.15 mm (0.006 in.)
NOTE:
Check front wheel bearing for looseness before measure-
ment.
Cylinder Slide Guide Pin / Pin Bolt
Check guide pin for smooth movement as shown.
If it is found faulty, correct or replace. Apply rubber grease to guide
pin outer surface. Rubber grease should be the on whose viscosity
is less affected by such low temperature a ±40
C (±40
F).
Dust Boot
Check boot for breakage, crack and damage. If defective, replace.

YH4
GRAND
VITARA
1. Clips
2. Pads
3. Disc
4. Caliper carrier
5. Sensor
6. Shim
1. Caliper pin bolts
ELECTRIC brake
caliper
FRONT BRAKE 5B-5
INSTALLATION
NOTE:
See NOTE at the beginning of this section.
1) Install pad clips and pads.
NOTE:
Install pad with sensor to body center side of caliper.
2) Install caliper and torque caliper pin bolts to specification.
Tightening Torque
(a), (b): 27 N
.m (2.7 kg-m, 20.0 lb-ft) For TOKICO brake. .
caliper
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft) For SUMITOMO. . . . . .
(b): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
NOTE:
Make sure that boots are fit into groove securely.
3) Torque front wheel nuts to specification.
Tightening Torque
(b): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
4) Upon completion of installation, perform brake test.

YH4
GRAND
VITARA
1. Caliper pin bolts
1. Flexible hose bolt
FRONT BRAKE 5B-9
Caliper
Before installing caliper (cylinder body) to carrier, check to ensure
that guide pin (pin bolt) inserted in each caliper carrier hole can be
moved smoothly in thrust direction.
NOTE:
Where temperature gets as low as ±30
C in cold weather, use
rubber grease whose viscosity varies very little even at ±40
C
(±40
F).
INSTALLATION
1) Install caliper to caliper carrier.
2) Torque caliper pin bolts to specifications.
Tightening Torque
(a), (b): 27 N
.m (2.7 kg-m, 20.0 lb-ft) For TOKICO brake. .
caliper
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft) For SUMITOMO. . . . .
(b): 85 N.m (8.5 kg-m, 61.5 lb-ft) ELECTRIC brake
85 N.m (8.5 kg-m, 61.5 lb-ft)caliper
NOTE:
Make sure that boots are fit into groove securely.
3) Install brake flexible hose as shown and torque hose mounting
bolt to specification.
Tightening Torque
(b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
4) Torque wheel nuts to specification.
Tightening Torque
(c): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
5) After completing installation, fill reservoir with brake fluid and
bleed brake system. Perform brake test and check each
installed part for oil leakage.

YH4
GRAND
VITARA
1. Brake back plate
2. Cable cap
3. Brake cable
1. Parking brake shoe lever
2. Spring
3. Nipple end
5C-6 PARKING AND REAR BRAKE
INSTALLATION
Install parts in reverse order of removal procedure, noting the fol-
lowing.
1) Install brake cable cap to brake back plate securely as shown in
figure.
NOTE:
Color ring or tape on brake cable is for the purpose of identi-
fication. Use cable with the same colored ring as before re-
moval.
2) Install brake cable spring and nipple end to parking brake shoe
lever securely as shown in figure.
3) For brake shoe installation, refer to steps 1) and 4) of BRAKE
SHOE INSTALLATION of this section.
4) For brake drum installation, refer to steps 1) and 3) of BRAKE
DRUM INSTALLATION of this section.
5) For proper routing and secure clamping of parking brake cable.
6) For installation of cable to parking brake lever, refer to PARKING
BRAKE LEVER INSTALLATION of this section.
7) Upon completion of installation, adjust cable. (Refer to PARK-
ING BRAKE CHECK AND ADJUSTMENT in Section 5.) Then
check brake drum for dragging and brake system for proper per-
formance. After removing vehicle from hoist, brake test should
be performed.

YH4
GRAND
VITARA
5E1-8 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
ABS DIAGNOSTIC FLOW TABLE
Refer to the following pages for the details of each step.
STEP
ACTIONYESNO
1Perform customer complaint analysis, problem
symptom confirmation and diagnostic trouble code
check record and clearance. Is there any trouble code?Go to step 2.Go to step 5.
2Perform driving test. Is trouble symptom identified?Go to step 3.Go to step 6.
3Check diagnostic trouble code. Is it malfunction
code?Go to step 4.Go to step 5.
4Inspect and repair referring to applicable diagnostic trouble
code table in this section. Then perform final confirmation
test after clearing diagnostic trouble code. Is trouble recur?Go to step 7.END.
5Inspect and repair referring to DIAGNOSIS in
ªBRAKESº section. Then perform final confirmation test
after clearing diagnostic trouble code. Is trouble recur?Go to step 7.END.
6Check for intermittent problems referring to
INTERMITTENT AND POOR CONNECTION in
ªGENERAL INFORMATIONº section and related circuit
of trouble code recorded in step 1. Then perform final
confirmation test after clearing diagnostic trouble code.
Is trouble recur?Go to step 7.END.
7Perform diagnostic trouble code check record
and clearance. Is there any trouble code?Go to step 2.Go to step 5.

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-19
-1. ªABSº warning lamp
-2. ABS hydraulic unit / control
module assembly
-3. Diagnosis connector
3-1. Diag. switch terminal
3-2. Diag. ground terminal
-4. ABS hydraulic unit/
control module connector
of harness
1. ABS hydraulic
unit / control
module connector
TABLE ± D CODE (DTC) IS NOT OUTPUTTED EVEN WITH DIAG. SWITCH
TERMINAL CONNECTED TO GROUND
CIRCUIT DESCRIPTION
When the diag. switch terminal is connected to the ground with the ignition switch turned ON, the ABS control mod-
ule outputs a diagnostic trouble code by flashing ªABSº warning lamp.
INSPECTION
STEPACTIONYESNO
1Is it shorted diag. switch terminal and ground terminal by
service wire properly?Go to step 2.Connect service
wire securely.
21) Disconnect service wire.
2) Disconnect ABS hydraulic unit / control module
connector. (See Fig. 1)
3) Measure resistance between diag. switch terminal
and connector terminal ªA8º.
Is it infinite (
)?ªPº circuit open.Go to step 3.
31) Measure resistance between ground terminal of
monitor connector and body ground.
Is continuity indicated?Go to step 4.ªBº circuit open or
poor connection.
41) Check for proper connection to ABS hydraulic
unit / control module at terminal ªA8º and ªA10º.
2) If OK, then check ªABSº warning lamp circuit
referring to ªTABLE A, B and Cº.
Is it in good condition?Substitute a
known-good ABS
hydraulic unit /
control module
assembly and
recheck.Repair ªABSº
warning lamp
circuit.
Fig. 1

YH4
GRAND
VITARA
5E1-22 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
1. ABS hydraulic
unit / control
module connector
INSPECTION
STEPACTIONYESNO
1Is G sensor installed floor securely?Go to step 2.Tighten sensor or
bracket screw
securely. If not,
using new screw.
21) Ignition switch OFF.
2) Remove G sensor with bracket.
3) Check for proper connection to G sensor.
4) If OK then check G sensor referring to item
INSPECTION of G sensor.
Is it in good condition?Go to step 3.Replace G sensor.
31) Disconnect connectors from ABS hydraulic unit /
control module assembly (See Fig. 1) and G sensor.
2) Check for proper connection to ABS control module
at terminals ªA14º and ªA4º.
3) If OK, then turn ignition switch ON and measure
voltage between ªB / Wº terminal of sensor
connector and body ground.
Is it 10 ± 14 V?Go to step 4.ªB / Wº circuit open.
4Measure voltage between ªO / Wº terminal of sensor
connector and body ground.
Is it 0 V?Go to step 5.ªO / Wº circuit
shorted to power
circuit.
51) Ignition switch OFF.
2) Check that ªO / Wº circuit is free from open
or short to ground and ªO / Gº circuit.
Is it in good condition? (See Fig. 2)ªO / Gº circuit open.
If circuit is OK, substi-
tute a known-good
ABS hydraulic
unit / control module
assembly.ªO / Wº circuit open
or shorted to
ground or ªO / Gº
circuit.
Fig. 1 Fig. 2