1999 SUZUKI GRAND VITARA valve cover

YH4
GRAND
VITARA
3B1-20 POWER STEERING (P / S) SYSTEM
1. P/S fluid
reservoir
2. Suction hose
1. P / S pulley
2. Mounting bolt
9. Vane
10. Rotor
11. Snap ring
12. Side plate
13. Pulley (pump shaft)
14. Oil seal
15. Pump body
16. Flow control
valve Assembly 1. Suction connector
2. O-ring
3. Pressure switch
4. Flow control valve
(Relief valve)
5. Spring
6. Plug
7. Pump cover
8. Cam ring
REMOVAL
NOTE:
Be sure to clean each joint of suction and discharge sides
thoroughly before removal.
1) Remove suction hose from pump, then disconnect battery nega-
tive cable.
2) Remove P / S fluid reservoir with suction hose.
3) Remove union bolt. Then disconnect high pressure pipe from
pump.
NOTE:
As fluid flows out of disconnected joints, put a receptacle
under joints or a plug to pipe.
4) Disconnect pressure switch lead wire at switch terminal.
5) Loosen related bolts and remove power steering drive belt.
6) Remove P / S pump mounting bolt (s).
7) Remove P / S pump.
NOTE:
Plug each port of removed pump to prevent dust or any oth-
er foreign matter from entering.
DISASSEMBLY
1) Clean its exterior thoroughly.
2) With aluminum plates placed on vise first, grip pump body with
it.
3) Remove suction connector bolt, suction connector and O-ring
from pump body.
4) Remove power steering pressure switch (terminal set) from
pump body.
5) Remove plug, flow control spring and relief valve (flow control
valve) from pump body.
6) Remove cover bolts, pump cover and O-ring from pump body.
7) Remove snap ring from pump shaft.
8) Remove vanes from rotor.
9) Remove cam ring, rotor, side plate and O-rings from pump
body.
10) Pull out pulley from pump body.
11) Remove oil seal from pump body.

YH4
GRAND
VITARA
POWER STEERING (P / S) SYSTEM 3B1-21
1. Thickness gauge
INSPECTION
Pump Body, Cover, Side Plate and Shaft
Check sliding surfaces of each part for wear and damage.
If any defect is found, replace pump assembly.
Cam Ring
Check vane sliding surface of cam ring for wear and damage.
If any defect is found, replace pump assembly.
Rotor and Vane

Check sliding surfaces of rotor and vane for wear and damage.

Check clearance between rotor and vane.
Clearance: Standard 0.015 mm (0.0006 in.)
Limit 0.027 mm (0.0011 in.)
Replace pump assembly if any defect is found in above checks.
Relief Valve (Flow Control Valve) and Its Spring

Check fluid passage of relief valve and orifice of connector for ob-
struction (clogged).

Check sliding surface of relief valve for wear and damage.

YH4
GRAND
VITARA
3B1-24 POWER STEERING (P / S) SYSTEM
1. Pump cover
1. Pressure switch
1. Suction connector
2. O-ring
1. Suction connector
15) Gradually tighten new pump cover bolts to specified torque.
NOTE:
After installing pump cover, check to make sure that shaft
can be turned by hand.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
16) Apply power steering fluid to O-ring of terminal switch.
17) Install pressure switch to pump body.
Tightening Torque
(a): 28 N
.m (2.8 kg-m, 20.0 lb-ft)
18) Apply power steering fluid to relief valve (flow control valve).
19) Install relief valve (flow control valve) to pump body.
20) Install flow control spring.
21) Apply power steering fluid to O-rings of plug.
22) Install O-rings to plug.
23) Tighten plug to specified torque.
Tightening Torque
(a): 60 N
.m (6.0 kg-m, 43.5 lb-ft)
24) Apply power steering fluid to O-ring of suction connector.
25) Install O-ring to suction connector.
26) Install suction connector to pump body as shown in figure.
Tighten new suction connector bolts to specified torque.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-9
1-1. CUSTOMER COMPLAINT ANALYSIS
Record details of the problem (failure, complaint) and how it occurred as described by the customer.
For this purpose, use of such a questionnaire form as shown below will facilitate collecting information to the
point required for proper analysis and diagnosis.
CUSTOMER QUESTIONNAIRE (EXAMPLE)
Customer's name:Model:VIN:
Date of issue:Date Reg.Date of problem:Mileage:
Problem Symptoms

ªABSº warning light abnormal: fails to turn on/fails to go off /
flashes

Abnormal noise while vehicle is running: from motor, from valve,
other__________________

Wheel is locked at braking:

Pump motor does not stop (running):

Braking does not work:

Other:
Frequency of occurrence
Continuous/Intermittent ( times a day, a month) /
other______________
Conditions for Occurrence
of Problem

Vehicle at stop & ignition switch ON:

When starting: at initial start only / at every start / Other______________

Vehicle speed: while accelerating / while decelerating / at stop /
while turning / while running at constant speed /
other________________

Road surface condition: Paved road / rough road / snow-covered
road / other_________________

Chain equipment:
Environmental Condition
Weather: fair / cloudy / rain / snow / other___________________

Temperature: F (C)
Diagnostic Trouble Code

First check: Normal code/malfunction code ( )

Second check after
test drive: Normal code / malfunction code ( )