1999 SUZUKI GRAND VITARA tightening torque specification

YH4
GRAND
VITARA
3C
STEERING WHEEL AND COLUMN 3C-1
SECTION 3C
STEERING WHEEL AND COLUMN
(NOT EQUIPPED WITH AIR BAG)
NOTE:
All steering wheel and column fasteners are important parts in that they could affect the performance of
vital parts and systems, and / or could result in major repair expense. They must be replaced with one of
the same part number or with an equivalent part if replacement becomes necessary. Do not use a replace-
ment part of lesser quality of substitute design. Torque values must be used as specified during reassemb-
ly to assure proper retention of this part.
CONTENTS
GENERAL DESCRIPTION3C- 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS3C- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and repair required after accident 3C- 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE3C- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering wheel3C- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Combination switch3C- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering column assembly3C- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering lock assembly (ignition switch) 3C-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering lower shaft assembly3C-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking steering column for accident damage 3C-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustable steering column release lever 3C-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS3C-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOL3C-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION
This double tube type steering column has the following three important features in addition to the steering function:

The column is energy absorbing, designed to compress in a front-end collision.

The ignition switch and lock are mounted conveniently on this column.

With the column mounted lock, the ignition and steering operations can be locked to inhibit theft of the vehicle.
To insure the energy absorbing action, it is important that only the specified bolts be used as designated and that
they are tightened to the specified torque. When the column assembly is removed from the vehicle, special care
must be taken in handling it. Use of a steering wheel puller other than the one recommended in this manual or a
sharp blow on the end of the steering shaft, leaning on the assembly, or dropping the assembly could shear the
plastic shear pins which maintain column length and position.

YH4
GRAND
VITARA
1. Lower position
2. Upper position
3C-14 STEERING WHEEL AND COLUMN
09944-36011
Steering wheel remover
ADJUSTABLE STEERING COLUMN RELEASE
LEVER
INSPECTION
Check to make sure that the following:

Steering column moves smoothly when adjustable steering col-
umn release lever is at lower position (i.e., steering column is not
locked).

Steering column is fixed securely when adjustable steering col-
umn release lever is at higher position (i.e., steering column is
locked).
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Steering shaft nut333.323.5
Steering column mounting bolt232.317.0
Steering shaft joint bolt252.518.0
Steering lower shaft assembly lower joint bolt252.518.0
SPECIAL TOOL

YH4
GRAND
VITARA
3C1
AIR BAG STEERING WHEEL AND COLUMN 3C1-1
GENERAL DESCRIPTION3C1- 2 . . . . . . . . . . . . .
DIAGNOSIS3C1- 3 . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair Required after
Accident 3C1- 3. . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE3C1- 3 . . . . . . . . . . . . . . .
Service Precautions 3C1- 3. . . . . . . . . . . . . . . . .
Diagnosis and Servicing 3C1- 3. . . . . . . . . . . .
Disabling Air Bag System 3C1- 3. . . . . . . . . . .
Enabling Air Bag System 3C1- 3. . . . . . . . . . .
Handling and Storage 3C1- 3. . . . . . . . . . . . . .
Disposal 3C1- 3. . . . . . . . . . . . . . . . . . . . . . . . . .
Driver Air Bag (Inflator) Module 3C1- 4. . . . . . . .
Steering Wheel 3C1- 6. . . . . . . . . . . . . . . . . . . . . . Centering Contact Coil 3C1- 6. . . . . . . . . . . . .
Contact Coil and Combination Switch
Assembly 3C1- 7. . . . . . . . . . . . . . . . . . . . . . . . .
Steering Column 3C1- 9. . . . . . . . . . . . . . . . . . . .
Steering Lock Assembly (Ignition
Switch) 3C1-14. . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering Lower Shaft Assembly 3C1-15. . . . . . .
Checking Steering Column for Accident
Damage 3C1-17. . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustable Steering Column Release
Lever 3C1-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS3C1-18 . . . . . . . . . . . . . . . . . . .
SPECIAL TOOL3C1-18 . . . . . . . . . . . . . . . . . . . . . .
SECTION 3C1
AIR BAG STEERING WHEEL AND COLUMN
WARNING:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Please observe all WARNINGS and ªService Precautionsº under ªOn-Vehicle
Serviceº in air bag system section before performing service on or around the air bag system compo-
nents or wiring. Failure to follow WARNINGS could result in unintentional activation of the system
or could render the system inoperative. Either of these two conditions may result in severe injury.

The procedures in this section must be followed in the order listed to disable the air bag system tem-
porarily and prevent false diagnostic trouble codes from setting. Failure to follow procedures could
result in possible activation of the air bag system, personal injury or otherwise unneeded air bag sys-
tem repairs.
CAUTION:
When fasteners are removed, always reinstall them at the same location from which they were re-
moved. If a fastener needs to be replaced, use the correct part number fastener for that application. If
the correct part number fastener is not available, a fastener of equal size and strength (or stronger) may
be used. Fasteners that are not reused, and those requiring thread-locking compound, will be called
out. The correct torque value must be used when installing fasteners that require it. If the above proce-
dures are not followed, parts or system damage could result.
CONTENTS

YH4
GRAND
VITARA
1. Lower position
2. Upper position
3C1-18 AIR BAG STEERING WHEEL AND COLUMN
09944-36011
Steering wheel remover
ADJUSTABLE STEERING COLUMN RELEASE
LEVER
INSPECTION
Check to make sure that the following:

Steering column moves smoothly when adjustable steering col-
umn release lever is at lower position (i.e., steering column is not
locked).

Steering column is fixed securely when adjustable steering col-
umn release lever is at upper position (i.e., steering column is
locked).
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Driver air bag (inflator) module bolt90.96.5
Steering shaft nut333.323.5
Steering column mounting bolt232.317.0
Steering shaft joint bolt252.518.0
Steering lower shaft assembly lower joint bolt252.518.0
Shift (key) interlock cable screw2.20.221.6
SPECIAL TOOL

YH4
GRAND
VITARA
3D
FRONT SUSPENSION 3D-1
GENERAL DESCRIPTION3D- 2 . . . . . . . . . . . . . .
DIAGNOSIS3D- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table 3D- 3. . . . . . . . . . . . . . . . . . . . . .
Stabilizer Bar and Bushing Check 3D- 3. . . . . .
Strut Damper and / or Coil Spring Check 3D- 3. .
Suspension Arm / Knuckle Check 3D- 3. . . . . . . .
Suspension Control Arm Joint Check 3D- 4. . . .
Suspension Control Arm Bushing Check 3D- 4.
Wheel Disc, Nut & Bearing Check 3D- 4. . . . . .
ON-VEHICLE SERVICE3D- 5 . . . . . . . . . . . . . . . . Stabilizer Bar / Bushings 3D- 5. . . . . . . . . . . . . . .
Strut Damper 3D- 6. . . . . . . . . . . . . . . . . . . . . . . .
Coil Spring 3D- 8. . . . . . . . . . . . . . . . . . . . . . . . . .
Bump Stopper / Spring Rubber Seat 3D-11. . . . .
Wheel Hub (Included Wheel Bearing) 3D-12. . .
Knuckle / Wheel Spindle 3D-17. . . . . . . . . . . . . . . .
Suspension Control Arm / Bushings 3D-21. . . . . .
TIGHTENING TORQUE
SPECIFICATIONS3D-23 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS3D-24 . . . . . .
SPECIAL TOOLS3D-25 . . . . . . . . . . . . . . . . . . . . . .
SECTION 3D
FRONT SUSPENSION
CAUTION:

All front suspension fasteners are an important attaching part in that it could affect the performance
of vital parts and systems, and / or could result in major repair expense. They must be replaced with
one of the same part number or with an equivalent part if replacement becomes necessary. Do not
use a replacement part of lesser quality or substitute design. Torque values must be used as specified
during reassembly to assure proper retention of this part.

Never attempt to heat, quench or straighten any front suspension part. Replace it with a new part or
damage to the part may result.
CONTENTS

YH4
GRAND
VITARA
FRONT SUSPENSION 3D-7
1. E-ring
2. Bracket end surface
INSTALLATION
1) Install strut by reversing removal steps 1) ± 8). Insert bolts in
such a direction as shown.
2) Torque all fasteners to specifications.
Tightening Torque
(a): 55 N
.m (5.5 kg-m, 40.0 lb-ft)
(b): 95 N
.m (9.5 kg-m, 69.0 lb-ft)
(c): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
NOTE:
Brake hose installation.
Don't twist hose when installing it. Install E-ring as far as
bracket end surface as shown.

YH4
GRAND
VITARA
3D-10 FRONT SUSPENSION
ªaº < ªbº
1. Circlip
2. Large diameter
1. Axle shaft drive flange
2. Bolt 1. Spring seat
Bottom
INSTALLATION
Reverse removal procedure to install coil spring.
NOTE:
Upper and lower diameters of coil spring are different.
Bring larger diameter end at bottom and set its open end in
place on spring seat.

Be sure to use specified torque for tightening each fastener.

Refer to torque specification chart at the end of this section.

As for ball stud nut, be sure to insert split pin and bend it after tight-
ening it.

Tighten tie-rod end nut with pushing ball stud to upper side so as
not ball stud to be rotated.

For 4WD vehicle
Apply lithium grease to front drive shaft washer and front wheel
spindle outer.
ªAº: Grease 99000-25010

For 4WD vehicle
When installing circlip to drive shaft, utilize screw hole in drive
shaft to pull it out and bring large diameter of circlip at right as
shown.

For 4WD vehicle
When installing axle shaft drive flange to wheel hub, apply sealant
to mating surface of axle shaft drive flange and tighten flange bolt
to specified torque.
ªAº: Sealant 99000-31090
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

YH4
GRAND
VITARA
(a)
1. Axle shaft drive flange
2. Bolt1. Hub cap
2. Wheel hub
3D-20 FRONT SUSPENSION

Tighten control arm ball stud nut
When tightening ball stud nut, use new nut and tighten it to speci-
fied torque.
Tightening Torque
(a): 60 N
.m (6.0 kg-m, 43.5 lb-ft)

For 2WD vehicle
Apply water tight sealant to mating surface of wheel hub and
install hub cap to wheel hub.
ªAº: Sealant 99000-31090

For 4WD vehicle
When installing axle shaft drive flange to wheel hub, apply sealant
to mating surface of axle shaft drive flange.
ªAº: Sealant 99000-31090
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

For installation procedures of wheel hub component, refer to
ªWHEEL HUB (INCLUDED WHEEL BEARING)º in this section.

Connect tie-rod end to knuckle and tighten new tie-rod end nut.
Tightening Torque
(a): 43 N
.m (4.3 kg-m, 31.5 lb-ft)

For any tightening torque other than those specified in text, refer
to ªTIGHTENING TORQUE SPECIFICATIONº in this section.