1999 SUZUKI GRAND VITARA lighting

YH4
GRAND
VITARA
Terminal
Wire ColorSwitch Position
Terminal
Switch Position
Wire Color
HEAD
OFFHI
PASS SMALL
8B-6 LIGHTING SYSTEM
ON-VEHICLE SERVICE
HEADLIGHTS
HEADLIGHT SWITCH (IN COMBINATION SWITCH)
INSPECTION
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace switch.
Lighting Switch
ELTH
WGR
OFF
SMALL
HEAD
Dimmer & Passing Switch
EDHLHUHF
W/BR/WRR/B
Passing (PASS)
Low Beam
High Beam (HI)
REMOVAL AND INSTALLATION
For vehicle without air bag system, refer to Section 3C COMBINA-
TION SWITCH, and for vehicle with air bag system, refer to Section
3C1 CONTACT COIL AND COMBINATION SWITCH ASSEMBLY.
REMOVAL
1) Disconnect negative cable at battery.
2) Remove front grille.
3) Disconnect harness and couplers from headlight assembly.
4) Remove three bolts and pull headlight assembly off vehicle.
INSTALLATION
Reverse removal procedure for installation.
Make sure to follow HEADLIGHT AIMING WITH SCREEN and aim
headlight after installation.

YH4
GRAND
VITARA
LH steering vehicle shown
X-X:Horizontal center line of headlight bulbs
A-A:Vertical center line of left headlight bulb
B-B:Vertical center line of right headlight bulb1. Screen
2. For right / left adjustment
3. For up / down adjustment
(for vehicle without leveling system)
4. For up / down adjustment
(for vehicle with leveling system)
5. Headlight leveling actuatorHOT
SPOT LH. HEADLIGHT RH. HEADLIGHT
LIGHTING SYSTEM 8B-7
BULB REPLACEMENT
WARNING:
Don't touch when the bulb is hot.
1) Disconnect negative cable at battery.
2) Disconnect harness from bulb.
3) Remove socket cover and bulb.
4) Replace bulb and install in reverse removal procedure.
HEADLIGHT AIMING WITH SCREEN
NOTE:

Unless otherwise obligated by local regulations, adjust
headlight aiming according to following procedure.

After replacing headlight, be sure to perform its aiming.

When inspecting and adjusting headlight with leveling sys-
tem, make sure to set the leveling switch to ª0º position with
IG switch ON.
Before adjustment, make sure the following.
a) Place vehicle on a flat surface in front of blank wall as below
ahead of headlight surface.
Clearance ªaº: 10 m (32.8 ft)
b) Adjust air pressure of all tires to a specified value respectively.
c) Bounce vehicle body up and down by hand to stabilize suspen-
sion.
d) Carry out one driver aboard.
Driver's weight: 75 kg (165 lb)
Adjustment
1) Check to see if hot spot (high intensity zone) of each main (low)
beam axis falls as illustrated.
Clearance ªHº: Approx. 130 mm (5.15 in.)
2) If headlight aiming is not set properly, align it to specification by
adjusting aiming screw and aiming gear.

YH4
GRAND
VITARA
8B-8 LIGHTING SYSTEM
HEADLIGHTS WITH LEVELING SYSTEM
(IF EQUIPPED)
LEVELING SWITCH
INSPECTION
To check the switch operation, substitute it with a new one. If proper
operation is obtained, it means the switch is defective.
Replace it with a new one.
LEVELING ACTUATOR
INSPECTION
All headlight system couples connected including leveling actuator
and switch, and at Ignition switch ON, listen to the leveling actuator
sound on both actuators according to the movement of the leveling
switch. If no sound is heard with the movement of the leveling
switch, replace headlight assembly.

YH4
GRAND
VITARA
1. Meter cluster
2. Hazard switch
Terminal
Wire ColorSwitch Position
LH steering vehicle shown
LIGHTING SYSTEM 8B-9
TURN SIGNAL AND HAZARD WARNING
LIGHTS
TURN SIGNAL SWITCH (IN COMBINATION SWITCH)
INSPECTION
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace switch.
TLTBTR
G/RGG/Y
L
N
R
REMOVAL AND INSTALLATION
Refer to Section 3C COMBINATION SWITCH for vehicle without air
bag system and Section 3C1 CONTACT COIL AND COMBINA-
TION SWITCH ASSEMBLY for vehicle with air bag system.
HAZARD SWITCH
REMOVAL
1) Remove meter cluster.
2) Pull hazard switch out of instrument panel.
3) Disconnect coupler from hazard switch.
4) Remove hazard switch.
INSTALLATION
Reverse removal procedure.
INSPECTION
Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace siwtch.

YH4
GRAND
VITARA
8B-10 LIGHTING SYSTEM
1. Hazard relay
2. Junction box
3. Fuse box
Type A
Type B
3
3
2
HAZARD RELAY
INSPECTION
Connect battery and tester as shown.
Unless a continued click sound is heard, replace relay.

YH4
GRAND
VITARA
LIGHTING SYSTEM 8B-11
REAR FOG LIGHT (IF EQUIPPED)
REAR FOG LIGHT SWITCH
INSPECTION
Check for continuity between terminals at each switch position
shown below. Hold the switch button (ON or OFF) pushed in during
checking switch.
NOTE:
Rear fog light lights up only when headlights (low or high
beams) or front fog lights (if equipped) are ON.
Rear fog lights turns OFF automatically when headlights or
front lights are turned OFF.

YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-15
DIAGNOSTIC TROUBLE CODE TABLE (Page 2 of 2)
DIAGNOSTIC TROUBLE CODEDIAGNOSISNO.MODEDIAGNOSIS
41Resistance high
42Driver
pretensionerResistance low
43circuit
(if equipped)Short to ground
44Short to power circuit
45Resistance highDiagnose trouble
di t ªDi
46Passenger
pretensionerResistance low
according to ªDiagnos-
tic Flow Tableº corre-
sponding to each code
47circuit
(if equipped)Short to ground
s onding to each code
No.
48Short to power circuit
51SDMFrontal crash detected
61ªAIR BAGº warning lamp circuit
71SDMInternal fault
NOTE:

When 2 or more codes are indicated, the lowest numbered code will appear first.

If a code not listed on the table is displayed, then the SDM is faulty.

Current DTC and history DTC can be identified by lighting and flashing of ªAIR BAGº warning lamp as
follows.
Current DTC is set.
(Abnormality exists at present.)History DTC is set only. (Faulty condi-
tion occurred once in the past but nor-
mal condition is restored at present.)
ªAIR BAGº warning lamp
after ignition switch ONRemains ON.Flashing 6 times and turns OFF.
ªAIR BAGº warning lamp
when grounding diagnosis
switch
Current DTC is displayed.History DTC is displayed.
However, if a multiple number of DTC's are set an even one of them is a current DTC, ªAIR BAGº warning
lamp remains on after ignition switch is turned ON. Therefore, it is not possible to identify any of them
as to whether it is a current one or a history one. (But use of scan tool (Tech 1) will make identification
possible.)