1999 SUZUKI GRAND VITARA Mount

YH4
GRAND
VITARA
(A)STEERING WHEEL
AIR BAG SYSTEM 10B-31
CODE 19 ± PASSENGER AIR BAG INITIATOR CIRCUIT SHORT TO POWER CIRCUIT
(Page 2 of 2)
NOTE:
Before executing items in this table, be sure to perform ªAir Bag Diagnostic Check Flow Tableº.
STEP
ACTIONYESNO
11) With ignition switch OFF, disconnect
passenger air bag (inflator) module
connector behind the glove box.
2) Check proper connection to passenger
air bag (inflator) module at terminals in ªBº
connector.
3) If OK then connect Special Tool (B) to
passenger air bag (inflator) module
connector disconnected at the step 1).
4) With ignition switch ON, is DTC 19
current?Go to step 2.1) Ignition switch OFF.
2) Replace passenger air
bag (inflator) module.
21) With ignition switch OFF, disconnect
Special Tool (B) and SDM.
2) Measure voltage from ªA3º terminal to
body ground.
3) With ignition switch ON, is voltage 1 V or
less?Substitute a known-good
SDM and recheck.Repair short from ªYº or
ªY/Rº wire circuit to power
circuit.
Fig. for STEP 1 and 2 Fig. for STEP 2
Special Tool
(A): 09932-76010
(B): 09932-75010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Clear diagnostic trouble codes (refer to ªDiagnostic Trouble Code (DTC) Clearanceº), if any.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.

YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-33
BASE OF COLUMN1. Paper
STEERING
WHEEL
CODE 21 ± DRIVER AIR BAG INITIATOR CIRCUIT RESISTANCE HIGH (Page 2 of 2)
STEPACTIONYESNO
31) With ignition switch OFF, disconnect Special
Tool (B) then reconnect contact coil connector
located near the base of the steering column.
2) Remove driver air bag (inflator) module from
steering wheel (Refer to SECTION 3C1).
3) Check proper connection to driver air bag
(inflator) module at terminals in ªDº connector.
4) If OK then connect Special Tool (B) to driver
air bag (inflator) module disconnected at step 2).
5) With ignition switch ON, is DTC 21 current?1) Ignition switch OFF.
2) Replace contact coil
assembly (Refer to
SECTION 3C1).1) Ignition switch OFF.
2) Replace driver air
bag (inflator)
module (Refer to
SECTION 3C1).
Fig. for STEP 1 and 2 Fig. for STEP 2
Fig. for STEP 3
Special Tool
(A): 09932-76010
(B): 09932-75010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Clear diagnostic trouble codes (refer to ªDiagnostic Trouble Code (DTC) Clearanceº), if any.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.

YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-35
BASE OF COLUMN1. Paper
STEERING
WHEEL
CODE 22 ± DRIVER AIR BAG INITIATOR CIRCUIT RESISTANCE LOW (Page 2 of 2)
STEPACTIONYESNO
31) With ignition switch OFF, disconnect Special
Tool (B) then reconnect contact coil connector
located near the base of the steering column.
2) Remove driver air bag (inflator) module from
steering wheel (Refer to SECTION 3C1).
3) Check proper connection to driver air bag
(inflator) module at terminals in ªDº connector.
4) If OK then connect Special Tool (B) to driver air
bag (inflator) module disconnected at step 2).
5) With ignition switch ON, is DTC 22 current?1) Ignition switch OFF.
2) Replace contact coil
assembly (Refer to
SECTION 3C1).1) Ignition switch OFF.
2) Replace driver air
bag (inflator)
module (Refer to
SECTION 3C1).
Fig. for STEP 1 and 2 Fig. for STEP 2
Fig. for STEP 3
Special Tool
(A): 09932-76010
(B): 09932-75010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Clear diagnostic trouble codes (refer to ªDiagnostic Trouble Code (DTC) Clearanceº), if any.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.

YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-37
(A)BASE OF COLUMN
STEERING
WHEEL
CODE 24 ±DRIVER AIR BAG INITIATOR CIRCUIT SHORT TO GROUND (Page 2 of 2)
STEPACTIONYESNO
31) With ignition switch OFF, disconnect Special
Tool (B) then reconnect contact coil connec-
tor located near the base of the steering
column.
2) Remove driver air bag (inflator) module from
steering wheel (Refer to SECTION 3C1).
3) Check proper connection to driver air bag
(inflator) module at terminals in ªDº
connector.
4) If OK then connect Special Tool (B) to driver
air bag (inflator) module disconnected at
step 2).
5) With ignition switch ON, is DTC 24 current?1) Ignition switch OFF.
2) Replace contact coil
assembly (Refer to
SECTION 3C1).1) Ignition switch OFF.
2) Replace driver air bag
(inflator) module
(Refer to SECTION
3C1).
Fig. for STEP 1 and 2 Fig. for STEP 2
Fig. for STEP 3
Special Tool
(A): 09932-76010
(B): 09932-75010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Clear diagnostic trouble codes (refer to ªDiagnostic Trouble Code (DTC) Clearanceº), if any.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.

YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-39
(A)
STEERING
WHEELBASE OF COLUMN
CODE 25 ± DRIVER AIR BAG INITIATOR CIRCUIT SHORT TO POWER CIRCUIT (Page 2 of 2)
STEPACTIONYESNO
31) With ignition switch OFF, disconnect Special
Tool (B) then reconnect contact coil connector
located near the base of the steering column.
2) Remove driver air bag (inflator) module from
steering wheel (Refer to SECTION 3C1).
3) Check proper connection to driver air bag
(inflator) module at terminals in ªDº connector.
4) If OK then connect Special Tool (B) to driver
air bag (inflator) module disconnected at
step 2).
5) With ignition switch ON, is DTC 25 current?1) Ignition switch OFF.
2) Replace contact coil
assembly (Refer to
SECTION 3C1).1) Ignition switch OFF.
2) Replace driver air bag
(inflator) module
(Refer to SECTION
3C1).
Fig. for STEP 1 and 2 Fig. for STEP 2
Fig. for STEP 3
Special Tool
(A): 09932-76010
(B): 09932-75010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Clear diagnostic trouble codes (refer to ªDiagnostic Trouble Code (DTC) Clearanceº), if any.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.

YH4
GRAND
VITARA
(A)
AIR BAG SYSTEM 10B-41
CODE 31 ± POWER SOURCE VOLTAGE HIGH (Page 2 of 2)
NOTE:
Before executing items in this table, be sure to perform ªAir Bag Diagnostic Check Flow Tableº.
STEP
ACTIONYESNO
11) With ignition switch OFF, disconnect SDM.
2) Check proper connection to SDM at
ªA16º terminal.
3) If OK then ignition switch ON, and then check
voltage from ªA16º terminal on SDM harness
connector to body ground.
4) Is voltage 14 V or less?Go to step 2.Check Charging System
and repair as necessary.
(Refer to SECTION 6H
ªChanging Systemº)
21) With ignition switch OFF, reconnect SDM
2) With ignition switch ON, is DTC 31 current?Substitute a known-
good SDM and recheck.Check Charging System
and repair as necessary.
(Refer to SECTION 6H
ªChanging Systemº)
Fig. for STEP 1
Special Tool
(A): 09932-76010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Clear diagnostic trouble codes (refer to ªDiagnostic Trouble Code (DTC) Clearanceº), if any.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.

YH4
GRAND
VITARA
(A)
AIR BAG SYSTEM 10B-43
CODE 32 ± POWER SOURCE VOLTAGE LOW (Page 2 of 2)
NOTE:
Before executing items in this table, be sure to perform ªAir Bag Diagnostic Check Flow Tableº.
STEP
ACTIONYESNO
11) Measure voltage on battery.
2) Is voltage 11 V or more?Go to step 2.Check Charging System
and repair as necessary.
(Refer to SECTION 6H
ªChanging Systemº)
21) With ignition switch OFF, disconnect SDM.
2) Check proper connection to SDM at ªA16º
terminal.
3) If OK then ignition switch ON, and then check
voltage from ªA16º terminal on SDM harness
connector to body ground.
4) Is voltage 8 V or more?Go to step 4.Go to step 3.
31) With ignition switch OFF, disconnect ignition
connector (ªFº connector) in air bag harness.
2) Check proper connection at terminal in ªFº
connector.
3) If OK then ignition switch ON, and then check
voltage from terminal in ªFº connector on main
harness to body ground.
4) Is voltage 8 V or more?Repair poor connec-
tion, high resistance
in ªBI/Rº or ªBI/Bº
circuit of air bag
harness or
ªAIR BAGº fuse.Possibly faulty points are
as follows. Check each of
them and repair as
necessary.

Circuit from battery to
ªFº connector

Charging System
(Refer to SECTION
6H ªChanging Systemº)
41) With ignition switch OFF, reconnect SDM
2) With ignition switch ON, is DTC 32 current?Substitute a known-
good SDM and
recheck.Check Charging System
and repair as necessary.
(Refer to SECTION 6H
ªChanging Systemº)
Fig. for STEP 2
Special Tool
(A): 09932-76010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Clear diagnostic trouble codes (refer to ªDiagnostic Trouble Code (DTC) Clearanceº), if any.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.

YH4
GRAND
VITARA (A)
For DTC 45
ªA11º
ªA12º
(A)
For DTC 41
STEERING WHEEL 1. Pretensioner
harness
EXAMPLE: For driver side
AIR BAG SYSTEM 10B-45
CODE 41 ± DRIVER PRETENSIONER INITIATOR CIRCUIT RESISTANCE HIGH
CODE 45 ± PASSENGER PRETENSIONER INITIATOR CIRCUIT RESISTANCE HIGH
(Page 2 of 2)
NOTE:
Before executing items in this table, be sure to perform ªAir Bag Diagnostic Check Flow Tableº.
STEP
ACTIONYESNO
11) With ignition switch OFF, remove front
pillar lower trim of applicable side then
disconnect seat belt pretensioner
connector.
2) Check proper connection to applicable
seat belt pretensioner at terminals in ªGº
or ªHº connector.
3) If OK then connect Special Tool (B) to
seat belt pretensioner connector
disconnected at the step 1).
4) With ignition switch ON, is DTC 41 or
45 still current?Go to step 2.1) Ignition switch OFF.
2) Replace seat belt preten-
sioner (Refer to
SECTION 10A).
21) With ignition switch OFF, disconnect
SDM.
2) Check proper connection to SDM at
terminals ªA13º and ªA14º or ªA11º
and ªA12º.
3) If OK then measure resistance between
ªA13º and ªA14º terminals or ªA11º and
ªA12º terminals with connected Special
Tool (B).
4) Is resistance 2.9
or less?Substitute a known-
good SDM and recheck.DTC41:
Repair high resistance or
open in ªPº or ªWº wire
circuit.
DTC45:
Repair high resistance or
open in ªLgº or ªBrº wire
circuit.
Fig. for STEP 1 and 2 Fig. for STEP 2
Special Tool
(A): 09932-76010
(B): 09932-75010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Clear diagnostic trouble codes (refer to ªDiagnostic Trouble Code (DTC) Clearanceº), if any.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.