1999 SUZUKI GRAND VITARA Stall

YH4
GRAND
VITARA
REAR SUSPENSION 3E-15
1. Inner oil seal
2. Axle housing
1. Hammer
2. Screwdriver
3. Oil seal protector
4. Oil seal
5. Body center
REAR AXLE SHAFT INNER OIL SEAL
REMOVAL
1) Remove rear axle shaft. For details, refer to steps 1) to 7) of
REAR AXLE SHAFT REMOVAL in this section.
2) Fix brake back plate by inserting screwdriver to the hole for bear-
ing retainer mounting.
3) Remove rear axle shaft inner oil seal.
NOTE:
Take care not to bend the brake pipe.
INSTALLATION
1) Using special tool drive in oil seal until it contacts oil seal protec-
tor in axle housing.
NOTE:

Make sure that oil seal is free from inclination as it is
installed.

Refer to figure so that oil seal is installed in proper direc-
tion.
Special Tool
(A): 09913-75510
ªAº: Grease 99000-25010
ªBº: Sealant 99000-31110
2) For procedure hereafter, refer to steps 6) to 11) of REAR AXLE
SHAFT INSTALLATION in this section.

YH4
GRAND
VITARA
1. Lower rod
2. Body center
1. Rear axle housing
2. Spring seat
3. Coil spring
4. Stepped part
1. Axle housing ªAº 1. Body center
1
2
1
REAR SUSPENSION 3E-19
INSTALLATION
Install removed parts in reverse order of removal, noting the follow-
ing.
1) Place rear axle housing on floor jack. Then install upper / lower
rod rear mounting bolts (right & left) in proper direction as shown
(refer to UPPER ROD INSTALLATION for upper rod bolts). At
this time, mount nuts but don't tighten them.
2) Install coil spring (right & left) on spring seat of axle housing and
raise axle housing.
NOTE:
When seating coil spring, mate spring end with stepped
part of rear axle spring seat as shown.
3) Install lateral rod to rear axle housing.
4) Install lower part of shock absorber to right and left sides of axle
housing and install bolts in proper direction as shown in figure.
At this time, mount nuts but don't tighten them.
5) Clean mating surfaces of axle housing and differential carrier
and apply sealant to housing side.
ªAº: Sealant 99000-31110
6) Install differential carrier assembly to axle housing and tighten
carrier nuts to specified torque.
Tightening Torque
(a): 55 N
.m (5.5 kg-m, 40.0 lb-ft)

YH4
GRAND
VITARA
1. Axle housingªAº
(c)
1. Axle housing
3E-20 REAR SUSPENSION
7) For vehicle with ABS, connect wheel speed sensor coupler and
install harness.
8) Install propeller shaft and torque nuts to specification.
Tightening Torque
(b): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
9) Remove floor jack from axle housing and connect breather
hose onto axle housing and clamp it securely.
10) Connect brake pipes onto axle housing and clamp them se-
curely.
For clamping positions, refer to SECTION 5A of this manual.
11) Connect brake flexible hose to bracket on axle housing and se-
cure it with E-ring.
12) Install LSPV stay to axle housing, tighten LSPV stay bolt to
specified torque.
And adjust LSPV referring to ªLSPV ASSEMBLY INSPEC-
TION AND ADJUSTMENTº in SECTION 5A.
Tightening Torque
(c): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
13) Connect brake pipe to brake flexible hose and tighten brake
pipe flare nut to specified torque.
Tightening Torque
(d): 16 N
.m (1.6 kg-m, 11.5 lb-ft)
14) Clean mating surface of axle housing (right & left) and brake
back plate, then apply sealant as shown.
ªAº: Sealant 99000-31110
15) Apply grease to axle shaft inner oil seal lip as shown.
ªAº: Grease 99000-25010

YH4
GRAND
VITARA
3. Container 1. Plug cap
2. Vinyl tube
1. Bearing retainer
(e)
(f)
(g)
REAR SUSPENSION 3E-21
16) Apply sealant to mating surface of bearing retainer with brake
back plate.
NOTE:
Make sure to remove old sealant before applying it anew.
ªBº: Sealant 99000-31110
17) Install rear axle shaft to rear axle housing and tighten bearing
retainer nuts to specified torque.
NOTE:
When installing rear axle shaft, be careful not to cause
damage to oil seal lip in axle housing.
Tightening Torque
(e): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
18) For vehicle with ABS, tighten wheel speed sensor bolt to speci-
fied torque.
Tightening Torque
(f): 21 N
.m (2.1 kg-m, 15.5 lb-ft)
19) Connect brake pipes to wheel cylinders (right & left) and tighten
brake pipe flare nuts to specified torque.
Tightening Torque
(g): 16 N
.m (1.6 kg-m, 11.5 lb-ft)
20) Install brake drum (right & left). For details, refer to SECTION
5C ªBRAKE DRUM INSTALLATIONº.
21) Refill differential gear housing with new specified gear oil. Re-
fer to ªON-VEHICLE SERVICEº in SECTION 7F for refill.
22) Fill reservoir with brake fluid and bleed brake system.(For
bleeding operation, see SECTION 5.)

YH4
GRAND
VITARA
3E-22 REAR SUSPENSION
23) Install wheel and tighten wheel nuts to specified torque.
Tightening Torque
(h): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
24) Upon completion of all jobs, depress brake pedal with about 30
kg (66 lbs) load three to ten times so as to obtain proper drum-
to-shoe clearance.
Adjust parking brake cable (for adjustment, see SECTION 5C
of this manual.)
25) Tighten parking brake lever cover screws.
26) Lower hoist.
27) Tighten right and left lower / upper rod nuts lateral rod mount
bolt and shock absorber nuts to specified torque.
NOTE:
When tightening these nuts, be sure that vehicle is off
hoist and in non loaded condition.
Tightening Torque
(i): 90 N
.m (9.0 kg-m, 65.0 lb-ft)
(j): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
28) Check to ensure that brake drum is free from dragging and
proper braking is obtained.
29) Perform brake test (foot brake and parking brake).
30) Check each installed part for oil leakage.

YH4
GRAND
VITARA
3E-24 REAR SUSPENSION
09924-74510
Bush remover handle09926-88310
Oil seal installer09942-15510
Sliding hammer09943-35512
Brake drum remover
09913-75510
Oil seal installer
SPECIAL TOOLS

YH4
GRAND
VITARA
3F
WHEELS AND TIRES 3F-1
GENERAL DESCRIPTION3F- 1 . . . . . . . . . . . . . .
Tires 3F- 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheels 3F- 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Tires 3F- 1. . . . . . . . . . . . . . . . . . .
Wheels Replacement 3F- 2. . . . . . . . . . . . . . . . .
Metric Lug Nuts and Wheel Studs 3F- 2. . . . . .
DIAGNOSIS3F- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table 3F- 3. . . . . . . . . . . . . . . . . . . . . .
Balancing Wheels 3F- 3. . . . . . . . . . . . . . . . . . . . MAINTENANCE AND MINOR
ADJUSTMENTS3F- 4 . . . . . . . . . . . . . . . . . . . . . .
Wheel and Tire 3F- 4. . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE3F- 6 . . . . . . . . . . . . . . . .
Wheel 3F- 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tire 3F- 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS3F- 8 . . . . . . . . . . . . . . . . . . . .
SECTION 3F
WHEELS AND TIRES
NOTE:
All wheel fasteners are important attaching parts in that they could affect the performance of vital parts
and systems, and / or could result in major repair expense. They must be replaced with one of the same
part number or with an equivalent part if replacement becomes necessary. Do not use a replacement part
of lesser quality or substitute design. Torque values must be used as specified during reassembly to as-
sure proper retention of all parts.
There is to be no welding as it may result in extensive damage and weakening of the metal.
CONTENTS
GENERAL DESCRIPTION
TIRES
This vehicle is equipped with following tire. P215 / 65 R16, 215 / 65 R16 or 235 / 60 R16
The tires are of tubeless type. The tires are designed to operate satisfactorily with loads up to the full rated load
capacity when inflated to the recommended inflation pressure.
Correct tire pressures and driving habits have an important influence on tire life. Heavy cornering, excessively rapid
acceleration, and unnecessary sharp braking increase tire wear.
WHEELS
Standard equipment wheels are following steel wheel. 16
6 1 / 2 J or 16
7JJ
REPLACEMENT TIRES
When replacement is necessary, the original equipment type tire should be used. Refer to the Tire Placard. Re-
placement tires should be of the same size, load range and construction as those originally on the vehicle. Use
of any other size or type tire may affect ride, handling, speedometer / odometer calibration, vehicle ground clear-
ance and tire or snow chain clearance to the body and chassis.
NOTE:
Do not mix different types of tires on the same vehicle such as radial, bias and bias-belted tires except in
emergencies, because vehicle handling may be seriously affected and may result in loss of control.
It is recommended that new tires be installed in pairs on the same axle. If necessary to replace only one tire, it
should be paired with the tire having the most tread, to equalize braking traction.

YH4
GRAND
VITARA
3F-2 WHEELS AND TIRES
The metric term for tire inflation pressure is the kilopascal (kPa).
Tire pressures will usually be printed in both kPa and psi on the Tire
Placard. Metric tire gauges are available from tool suppliers. The
chart, left table, converts commonly used inflation pressures from
kPa to psi.kPakgf / cm2psi
160
180
200
220
240
260
280
300
320
3401.6
1.8
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.423
26
29
32
35
38
41
44
47
50
Conversion:1 psi = 6.895 kPa
1 kgf / cm
2 = 98.066 kPa
WHEELS REPLACEMENT
Wheels must be replaced if they are bent, dented, have excessive
lateral or radial runout, leak air through welds, have elongated bolt
holes, if lug nuts won't stay tight, or if they are heavily rusted.
Wheels with greater runout than shown in left figure may cause ob-
jectional vibrations.
Wheels for replacement must be equivalent to the originally
equipped wheels in load capacity, diameter, rim width, off-set and
mounting configuration. A wheel of improper size or type may affect
wheel and bearing life, brake cooling, speedometer / odometer cal-
ibration, ground clearance to the body and chassis.
To measure the wheel runout, it is necessary to use accurate dial
indicator. The tire may be on or off the wheel. The wheel should be
installed to the wheel balancer of the like for proper measurement.
Take measurements of both lateral runout and radial runout at both
inside and outside of the rim flange. With dial indicator set in place
securely, turn the wheel one full revolution slowly and record every
reading of the indicator.
When the measured runout exceeds the specification and correc-
tion by the balancer adjustment is impossible, replace the wheel.
If the reading is affected by welding, paint or scratch, it should be
ignored.
Lateral runout limit ªaº: 1.20 mm (0.047 in.)
Radial runout limit ªbº: 1.20 mm (0.047 in.)
METRIC LUG NUTS AND WHEEL STUDS
All models use metric lug nuts and wheel studs (size M12 x 1.25).