1999 SUZUKI GRAND VITARA tightening torque specification

YH4
GRAND
VITARA
7E-16 DIFFERENTIAL (FRONT)
(a)
(a)
(a)
1. Drive shaft joint R
2. Differential housing3. Transmission jack
4. Screw driver
8) Using 2 large screwdrivers as levers, pull out right side drive
shaft joint from differential and dismount housing assembly from
vehicle.
CAUTION:
During above work, use care not to cause damage to
drive shaft boot.
REMOUNTING
For remounting, reverse dismounting procedure and use following
tightening torque.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
After tightening all fasteners properly, fill hypoid gear oil as speci-
fied and check tightening of plugs with specification.

YH4
GRAND
VITARA
DIFFERENTIAL (FRONT) 7E-17
09951-16080
Bearing installer09951-26010
Bush remover plate09918-18110
Air pressure regulator
09367-04002
3-way joint
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in FOREWORD of this manual.
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN.mKg-mlb-ft
Differential oil filler / level plug232.317.0
Differential oil drain plug232.317.0
Differential mounting front bolts858.561.5
Differential mounting bracket bolts505.036.5
Front drive shaft flange bolts505.036.5
Propeller shaft flange bolts505.036.5
Pump assembly bolts131.39.5
REQUIRED SERVICE MATERIAL
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
SealantSUZUKI BOND NO. 1215
(99000-31110)Front differential drain plug
SPECIAL TOOLS

YH4
GRAND
VITARA
7F
DIFFERENTIAL (REAR) 7F-1
The differential assembly is decisive in that the drive
power is concentrated there. Therefore, use of genu-
ine parts and specified torque is compulsory. Further,
because of sliding tooth meshing with high pressure
between bevel pinion and gear, it is mandatory to lu-
bricate them by hypoid gear oil.
SECTION 7F
DIFFERENTIAL (REAR)
CONTENTS
GENERAL DESCRIPTION7F-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS7F-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7F-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance Service7F-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dismounting7F-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remounting7F-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7F-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS7F-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7F-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION
The differential assembly using a hypoid bevel pinion
and gear is installed to the rear axle. It is set in the con-
ventional type axle housing.
The reduction ratio and differential case vary depend-
ing on transmission or engine type.

YH4
GRAND
VITARA
1. Breather hose
2. Oil filler / level plug
3. Rear drain plug
(Apply sealant)
Viscosity chart SAE
DIFFERENTIAL (REAR) 7F-3
ON-VEHICLE SERVICE
MAINTENANCE SERVICE
NOTE:

When having driven through water, check immediately if wa-
ter has entered (if so, oil is cloudy). Water mixed oil must be
changed at once.

Whenever vehicle is hoisted for any other service work than
oil change, also be sure to check for oil leakage and status
of breather hoses.
CHANGING OIL
NOTE:

Hypoid gear oil must be used for differential.

It is highly recommended to use SAE 80W-90 viscosity.
1) Before oil change or inspection, be sure to stop engine and lift
up vehicle horizontally.
2) Check oil level and existence of leakage. If leakage is found, cor-
rect its cause.
3) Drain old oil and pour proper amount of gear oil as specified
(roughly up to level hole).
4) Torque drain and level / filler plugs to specification.
ªAº: Sealant 99000-31110
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
(b): 28 N
.m (2.8 kg-m, 20.5 lb-ft)
Specified gear oil: Hypoid gear oil API GL-5
SAE 75W-85, 80W-90 or 90
For oil viscosity, refer to the chart
at the left.
Oil capacity : 2.2 liters (4.6 / 3.9 US / Imp. pt.)

YH4
GRAND
VITARA
1. Differential to rear axle nut
(a)
(a)
DIFFERENTIAL (REAR) 7F-5
REMOUNTING
1) Clean mating surfaces of rear axle and differential assembly and
apply sealant (Suzuki bond 1215) to axle side evenly.
ªAº: Sealant 99000-31110
2) Install differential assembly to axle and fix it with nuts tightened
to specified torque.
Tightening Torque
(a): 55 N
.m (5.5 kg-m, 40.0 lb-ft)
3) Install propeller shaft to joint flange aligning match marks and
torque flange bolts to specification.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
4) Install right and left rear axle shafts and drums.
(Refer to rear axle installation of SECTION 3E and rear brake
drum installation of SECTION 5.)
5) Install wheels.
6) Fill hypoid gear oil as specified and tighten plug to specification.
Lower lift.
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in Foreword of this manual.

YH4
GRAND
VITARA
7F-6 DIFFERENTIAL (REAR)
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN.mkg-mlb-ft
Differential oil filler / level plug505.036.5
Differential oil drain plug282.820.5
Propeller shaft flange bolts505.036.5
Differential carrier nuts555.540.0
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
SealantSUZUKI BOND NO. 1215
(99000-31110)

Rear differential oil drain plug

Mating surface of differential
housing

Mating surface of rear axle housing

YH4
GRAND
VITARA
1. Seat cushion
2. Seat back
3. Reclining assy (RH side)
4. Reclining assy (LH side)
5. Seat adjuster (RH outside)
6. Seat adjuster (RH inside)
7. Seat adjuster (LH outside)
8. Seat adjuster (LH inside)
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)
(b): 23 N.m (2.3 kg-m, 17.0 lb-ft)
1. Cover
2. Coupler(b)
9-34 BODY SERVICE
SEAT
FRONT SEAT
REMOVAL
1) Disconnect lead wire(s) at coupler (if equipped). Remove four
mounting bolts fixing front seat to seat rail to remove front seat.
2) Disassemble and repair seat as necessary.
INSTALLATION
Reverse removal procedure to install front seat.
Torque to specifications, as shown.
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)

YH4
GRAND
VITARA
1. Seat cushion
2. Seat back
3. Seat auto lock release handle
4. Seat hinge male
5. Hinge male cover
BODY SERVICE 9-35
REAR SEAT
REMOVAL
1) Remove four mounting bolt to remove seat cushion.
2) Remove four mounting bolts to remove seat back.
3) Disassemble and repair seat as necessary.
INSTALLATION
Reverse removal procedure to install rear seat.
Torque to specifications, as shown.
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)