1999 SUZUKI BALENO Indicator light

60G-74E
INSTRUMENT PANEL

INSTRUMENT PANEL

Instrument Panel 5-1

Instrument Cluster 5-2

Warning and Indicator Lights 5-3

Speedometer/Odometer/Tripmeter (if equipped) 5-5

Tachometer (if equipped) 5-6

Fuel Gauge 5-6

Temperature Gauge 5-6

Hazard Warning Switch 5-7

Rear Window Defroster Switch (if equipped) 5-7

Cigarette Lighter (if equipped) 5-7

Ashtray 5-8

Glove Box 5-8

Heating System (if equipped) 5-9

System Operating Instructions 5-10

Air Conditioning System (if equipped) 5-13

System Operating Instructions 5-13

37

INSTRUMENT PANEL
60G-74E

INSTRUMENT PANEL

1. Instrument cluster

2. Ignition switch

3. Lighting switch/Turn signal and

dimmer switch

4. Windscreen wiper and washer

switch

5. Hazard warning switch

6. Rear window defroster switch

(if equipped)

7. Other switches (if equipped)

8. Heater control panel

9. Audio system (if equipped)

10. Cigarette lighter (if equipped)

11. Ashtray

12. Bonnet release

13. Center ventilator

14. Side ventilator

15. Side defroster

16. Glove box

17. Fuse box

18. Cup holder (if equipped)

5-1
38

60G-74E
INSTRUMENT PANEL

INSTRUMENT CLUSTER

© Speedometer

® Odometer

© Trip meter (if equipped)

© Trip meter reset knob

© Tachometer (if equipped)

© Fuel gauge

® Temperature gauge

© Warning and indicator lights

60G-05-002

39

5-2

INSTRUMENT PANEL
60G-74E

WARNING AND INDICATOR LIGHTS

70F-07-070

Brake fluid level warning/Parking Brake

Indicator light

This light operates under three conditions:

1) when the ignition switch is turned to the

"START' position, 2) when the fluid in the brake

fluid reservoir falls below the specified level

or 3) when the parking brake is not fully

released and the ignition switch is in the "ON"

position. The light should go out after starting

the engine and fully releasing the parking

brake, if the fluid in the brake fluid reservoir is

adequate. If the light does not go off or comes

on whilst you are driving, it may mean that

there is something wrong with the vehicle's

braking system. If this happens, you should:

1) Pull off the road and stop carefully.

Remember that stopping distance may

be longer, you may have to push

harder on the pedal, and the pedal

may go down farther than normal.
2) Test the brakes by carefully starting and

stopping at the side of the road.

3) If you determine that it is safe, drive

carefully at low speed to the nearest dealer

for repairs.

Have the vehicle towed to the nearest

dealer for repairs.
or

4)

If any of the following conditions occur,

you should Immediately ask your

MARUTI dealer to inspect the brake

system.

• If the brake fluid level warning light

does not go out after the engine has

been started and the parking brake

has been fully released.

• If the brake fluid level warning light

does not come on when the ignition

switch is turned to the "START"

position.

• If the brake fluid level warning light

comes on at any time during vehicle

operation.

NOTE:

Because the disc brake system is self

adjusting, the fluid level will drop as the brake

pads become worn.

Replenishing the brake fluid reservoir is

considered normal periodic maintenance.
70F-03-039

Oil Pressure Light

This light comes on when the ignition switch

is turned on, and goes out when the engine

is started. The light will come on and remain

on if there is insufficient oil pressure. If the

light comes on when driving, pull off the

road as soon as you can and stop the

engine. Check the oil level and add oil if

necessary (see pages 9-8 and 9-9). If there

is enough oil, the lubrication system should

be inspected by your MARUTI dealer before

you drive the vehicle again.

5-3
40

60G-74E
INSTRUMENT PANEL

60G-09-002

CAUTION

If you operate the engine with this

light on, severe engine damage can

result.

Do not rely on the Oil Pressure Light

to indicate the need to add oil. Be

sure to periodically check the engine

oil level (see pages 9-8 and 9-9).
70F-03-009

Charging Light

This light comes on when the ignition switch

is turned on, and goes out when the engine is

started. The light will come on and remain on

if there is something wrong with the battery

charging system. If the light comes on when

the engine is running, the charging system

should be inspected immediately by your

MARUTI dealer.

CAUTION

Do not continue driving long with the

charging light ON as this will drain the

battery 'dead'.
72F-05-027

"Malfunction Indicator" Light

Your vehicle has a computer-controlled

emission control system. A "Malfunction

Indicator" light is provided on the instrument

panel to indicate when it is necessary to have

the emission control system serviced. The

"Malfunction Indicator" light comes on when

the ignition switch is turned to "ON" and goes

out when the engine is started.

If the "Malfunction Indicator" light comes on

when the engine is running, there is a problem

with the emission control system. Take the

vehicle to your MARUTI dealer to have the

problem corrected.

CAUTION

Continuing to drive the vehicle when

the "Malfunction Indicator" light is on

can cause permanent damage to the

vehicle's emission control system, and

can affect fuel economy and

driveability.

5-4

INSTRUMENT PANEL
60G-74E

70F-03-042

Turn Signal Indicators

When you turn on the left or right turn signals,

the corresponding green arrow on the

instrument panel will flash along with the

respective turn signal lights. When you turn

on the hazard warning switch, both arrows will

flash along with all of the turn signal lights.

70F-03-043

Main Beam (High Beam) Indicator Light

This indicator comes on when headlight main

beams (high beams) are turned on.
SPEEDOMETER/ODOMETER/

TRIPMETER (if equipped)

60G-05-003

© Speedometer

© Odometer

(D Trip meter

© Trip meter reset knob

The speedometer indicates vehicle speed in

km/h.The odometer records the total distance

the vehicle has been driven. The tripmeter can

be used to measure the distance travelled on

short trips or between fuel stops. You can reset

the tripmeter to zero by pushing the reset

knob.
CAUTION

Keep track of your odometer reading

and check the maintenance schedule

regularly for required services.

Increased wear or damage to certain

parts can result from failure to perform

required services at the proper mileage

intervals and your warranty rights may

be affected.

5-5

42
41

60G-74E
INSTRUMENT PANEL

TACHOMETER (if equipped)

FUEL GAUGE
TEMPERATURE GAUGE

60G-05-004

The tachometer indicates engine speed in

revolutions per minute.

Never drive with the engine speed

indicator in the red zone or severe

engine damage can result.
60G-05-005

This gauge gives an approximate indication

of the amount of fuel in the fuel tank as shown

in figure. "P stands for full and "E" stands for

empty.

If the indicator gets in the red zone, refill the

tank as soon as possible.

Note:

This vehicle has fuel gauge of new design.

Even when the ignition switch is "OFF", the

needle will not return to "E" position but will

show the reading.
60G-05-006

When the ignition switch is on, this gauge

indicates the engine coolant temperature.

Under normal driving conditions, the indicator

should stay within the normal, acceptable

temperature range between "H" and "C". If the

indicator approaches "H", and maintains that

reading, overheating is indicated. Follow the

instructions for engine overheating in the

EMERGENCY REMEDIES section.

CAUTION

Continuing to drive the vehicle when

engine overheating is indicated, can

result in severe engine damage.

43

5-6

INSTRUMENT PANEL

60G-74E

HAZARD WARNING SWITCH
REAR WINDOW DEFROSTER SWITCH CIGARETTE LIGHTER (if equipped)

(if equipped)

60G-05-007

Push in the hazard warning switch to activate

the hazard warning lights. All four turn signal

lights and both turn signal indicators will flash

simultaneously. To turn off the lights, push the

switch again.

Use the hazard warning lights to warn other

traffic during emergency parking or when your

vehicle could otherwise become a traffic

hazard.
60G-05-008

When the rear window is misted, push this

switch to clear the window. An indicator light

will be lit when the defroster is on. The

defroster will only work when the ignition

switch is in the "ON position. To turn off the

defroster, push the switch again.

CAUTION

The rear window defroster uses a large

amount of electricity. Be sure to turn

off after the window has become clear.
60G-05-009

To use the cigarette lighter, push it all the way

into the receptacle and release it. It will

automatically heat up and will pop out to its

normal position when it is ready for use.

5-7
44

60G-74E
INSTRUMENT PANEL

60G-05-018

Cool Face/Warm Feet

Push the "BI-LEVEL" button and move the air

intake lever to "FRESH AIR", the temperature

control lever to the desired temperature

position, and the fan switch to the desired fan

speed position. Unless the temperature control

lever is in the fully "COOL" position or fully

"HOT position, the air that comes out of the

center and side outlets will be cooler than the

air that comes out of the floor outlets.
60G-05-019

Defrosting/Warm Feet

Push the "HEAT & DEFROST' button and

move the air intake lever to "FRESH AIR", the

temperature control lever to the desired

temperature position, and the fan switch to

"HIGH". When the windscreen has become

clear, move the fan switch to the desired fan

speed position.
60G-05-020

Defrosting

Push the "DEFROST' button and move the

air intake lever to "FRESH AIR", the

temperature control lever to the desired

temperature position, and the fan switch to

"HIGH" Moving the temperature control lever

to a higher temperature position increases

defrosting efficiency. When the windscreen

has become clear, move the fan switch to the

desired fan speed position.

49

5-12

INSTRUMENT PANEL

60G-74E

AIR CONDITIONING SYSTEM

(if equipped)
SYSTEM OPERATING INSTRUCTIONS

60G-05-021

The air conditioning system can be used to

provide cooling and dehumidifying, as

described below. To turn on the air conditioning

system, push in the A/C button and move the

fan switch to a position other than "OFF". An

indicator light will come on when the air

conditioning system is on. To turn off the air

conditioning system, push the A/C button again.

During operation of the air conditioner, you may

notice slight changes in engine speed. These

changes are normal, the system is designed

so that the compressor turns on or off to

maintain the desired temperature. Less

operation of the compressor results in better

fuel economy.
60G-05-022

Normal Cooling (using outside air)

Push in the A/C button and the

"VENTILATION" button, and the move the air

intake lever to "FRESH AIR", the temperature

control lever to the "COOL" position, and the

fan switch to the desired fan speed position.

Moving the fan switch to a higher fan speed

position increases cooling efficiency.

If the ambient temperature is high enough to

cause insufficient cooling, use the "Quick

Cooling" as following.
60G -05-023

Quick Cooling (Using recirculated air)

The lever settings are the same as for normal

cooling except you move the air intake lever

to "RECIRCULATED AIR". If you use this

cooling method for a extended period of time,

the air in the vehicle can become

contaminated. Therefore, you should

occasionally move the air intake lever to

"FRESH AIR".

NOTE:

If your vehicle has been left in the sun with

the windows closed, it will cool faster if you

open the windows briefly while you operate

the air conditioner with the air intake lever at

"FRESH AIR" and the fan at high speed.

5-13
50

60G-74E
INSPECTION AND MAINTENANCE

POWER STEERING (if equipped)

CLUTCH PEDAL

60G-09-017

Check the steering box case, vane pump and

hose connections for leaks or damage.

Power steering fluid

Check the fluid level by looking at the reservoir

in the engine compartment when the fluid is

cold (about room temperature).

Check that the fluid level is between the

"UPPER" and "LOWER" lines. If the fluid level

is near the "LOWER" line, fill it up to the

"UPPER" line with an automatic transmission

fluid equivalent to DEXRON»-IIE or

DEXRON'-III. Do not overfill.
63B-09-00SE

Power steering belt

The tension of the belt should be such that

there is a deflection of 8-10mm (0.31 -0.39 in.)

when you press your thumb midway between

the pulleys.

The belt should also be examined to ensure

that it is not damaged. If necessary, have the

belt adjusted or replaced by your MARUTI

dealer.
70F-07-034

Measure the clutch pedal piay by moving the

clutch pedal with your hand and measuring

the distance it moves until you feel slight

resistance. The play in the clutch pedal should

be between 15-20 mm (0.6 - 0.8 in). If the

play is more or less than the above, or clutch

dragging is felt with the pedal fully depressed,

have the clutch inspected by your MARUTI

dealer.

101

9-18

INSPECTION AND MAINTENANCE

60G-74E

TYRES

60G-09-018

The front and rear tyre pressure specifications

for your vehicle are listed on the Tyre Inflation

Pressure Label and in the "SPECIFICATIONS"

section at the end of this book. Both the front

and rear tyres should have the specified tyre

pressure.

Tyre Inspection

Inspect your vehicle's tyres periodically by

performing the following checks:

1) Measure the air pressure with a tyre

gauge. Adjust the pressure if necessary.
Air pressures should be checked

when the tyres are cold or you may

get inaccurate readings.

Check the inflation pressure from

time to time while inflating the tyre

gradually, until the specified

pressure is obtained.

Never underinf late or overinf late the

tyres.

Underinflation can cause unusual

handling characteristics or can

cause the rim to slip on the tyre

bead, resulting in an accident or

damage to the tyre or rim.

Overinflation can cause the tyre to

burst, resulting in personal injury.

Overinflation can also cause

unusual handling characteristics

which may result In an accident.
70F-07-037E

2) Check that the depth of the tread groove

is more than 1.6 mm (0.06 in). To help you

check this, the tyres have moulded in tread

wear indicators in the grooves. When the

indicators appear on the tread surface, the

remaining depth of the tread is 1.6 mm

(0.06 in) or less and the tyre should be

replaced.

3) Check for abnormal wear, cracks and

damage. Any tyres with cracks or other

damage should be replaced. If any tyres

show abnormal wear, have them inspected

by your MARUTI dealer.

9-19
102

EMERGENCY SERVICE

60G-74E

CAUTION

Vehicle equipped with electronic fuel

injection system will not start by

pushing or towing as the fuel pump

will not work in this condition. This

starting method could also result in

permanent damage to the catalytic

converter. Use jump leads to start a

vehicle with a weak or flat battery.

60G-10-004E

When jump starting your vehicle, use the

following procedure:

1) Use only a 12 volt battery to jump start

your vehicle. Position the good 12V battery

close to your vehicle so that the jump leads

will reach both batteries. When using a

battery installed on another vehicle, DO

NOT LET THE VEHICLES TOUCH. Apply

the parking brakes fully on both vehicles.

2) Turn off all vehicle accessories, except

those necessary for safety reasons (for

example, headlights or hazard lights).
3) Make jump lead connections as follows:

a) Connect one end of the first jump lead

to the positive (+) terminal of the flat

battery.

b) Connect the other end to the positive

(+) terminal of the booster battery.

c) Connect one end of the second jump

lead to the negative (-) terminal of the

booster battery.

d) Make the final connection to an

unpainted, heavy metal part of the

engine of the vehicle with the flat

battery.

Never connect the jump lead directly

to the negative (-) terminal of the

discharged battery, or an explosion

may occur.

10-3
4) If the booster battery you are using is fitted

to another vehicle, start the engine of the

vehicle with the booster battery. Run the

engine at moderate speed.

5) Start the engine of the vehicle with the flat

battery.

6) Remove the jump leads in the exact

reverse order in which you connected

them.

118

60G-74E
EMERGENCY SERVICE

TOWING

If you need to have your vehicle towed, contact

a professional service.

CAUTION

To help avoid damage to your vehicle

during towing, proper equipment and

towing procedures must be used.

Manual Transmission

Whenever possible, your vehicle should be

towed from the front with the front wheels lifted.

If the steering and drivetrain are in good

condition, your vehicle may be towed from the

rear with the rear wheels lifted and the front

wheels on the ground. Before towing, make

sure the steering is unlocked and the

transmission is in neutral.
EMERGENCY REMEDIES

If the Starter Does Not Operate:

1) Try turning the ignition switch to the

"START" position with the headlights

turned on to determine the battery

condition. If the headlights go excessively

dim or go off, it usually means that either

the battery is flat or the battery terminal

contact is poor. Recharge the battery or

correct battery terminal contact as

necessary.

2) If the headlights remain bright, check the

fuses. If the reason for failure of the starter

is not obvious, there may be a major

electrical problem. Have the vehicle

inspected by your authorized MARUTI

dealer.

If the Engine is Flooded

If the engine is flooded with petrol, it may be

hard to start. If this happens, press the

accelerator pedal all the way to the floor and

hold it there while cranking the engine. (Do

not operate the starter motor for more than

15 seconds). Release the accelerator as soon

as the engine has started.
If the Engine Overheats

The engine could overheat temporarily under

severe driving conditions. If the engine coolant

temperature gauge indicates overheating

during driving:

1) Turn off the air conditioner, if equipped.

2) Take the vehicle to a safe place and park.

3) Let the engine run at normal idle speed

for a few minutes until the indicator is within

the normal, acceptable temperature range

between "H" and "C".

If you see or hear escaping steam, stop

the vehicle in a safe place and

Immediately turn off the engine to let it

cool. Do not open the bonnet when

steam is present. When the steam can

no longer be seen or heard, open the

hood to see if the coolant is still boiling.

If it is, you must wait until it stops

boiling before you proceed.

119

10-4