1999 SUZUKI BALENO battery

60G-74E
INSPECTION AND MAINTENANCE

INSPECTION AND MAINTENANCE

Periodic Maintenance Schedule.. 9-2

Engine Oil and Filter 9-7

Gear OH 9-10

Engine Coolant 9-11

Windscreen Washer Fluid 9-13

Air Cleaner 9-13

Spark Plugs 9-14

Brakes 9-15

Steering 9-17

Power Steering (if equipped) 9-18

Clutch Pedal 9-18

Tyres... 9-19

Battery 9-22

Fuses 9-23

Bulb Replacement , 9-25

Wiper Blades 9-29

83

INSPECTION AND MAINTENANCE

60G-74E

70F-05-002

You should take extreme care when

working on your vehicle to prevent

accidental injury. Here are a few

precautions that you should be

especially careful to observe:

• Do not leave the engine running in

garages or other confined areas.

• When the engine Is running, keep

hands, clothing, tools, and other

objects away from the fan and water

pump belt. Even though the fan may

not be moving, it can automatically

turn on without warning. ^
When it is necessary to do service

work with the engine running, make

sure that the parking brake is applied

fully and the transmission is in

Neutral.

Do not touch ignition wires or other

ignition system parts when starting

the engine or when the engine is

running, or you could receive an

electric shock.

Be careful not to touch a hot engine,

exhaust manifold and pipes, muffler,

radiator and water hoses.

Do not allow smoking, sparks, or

flames around gasoline or the

battery. Flammable fumes are

present.

Do not get under your vehicle if it is

supported only with the portable

jack provided in your vehicle.

Be careful not to cause accidental

short circuits between the positive

and negative battery terminals.

Keep used oil, coolant, and other

fluids away from children and pets.

Dispose of used fluids properly;

never pour them on the ground, into

sewers, etc.

9-1
84

60G-74E
INSPECTION AND MAINTENANCE

Interval: This interval should be Judged

by odometer reading or months,

whichever comes first.
km (x 1,000)

months

FUEL

1. Air cleaner Paved-road

Dusty condition

2. Accelerator cable and Throttle shafts

3. Fuel tank cap, fuel lines & connections(leakage,damage)

4. Fuel filter (leakage)

CLUTCH AND TRANSMISSION

1. Clutch pedal (play)

2. Clutch slipping (dragging or excessive damage)

3. Manual Transmission/Transfer and Differential oil (level, leakage)

DRIVE SHAFTS

1. Drive shafts boots (bent of boots damage)

BRAKE

1. Brake fluid (level, leakage)

2. Brake pedal (pedal-to-wall clearance)

3. Parking brake lever and cable (play, damage)

4. a. Brake discs and pads, (wear)

b. Brake drums & shoes

5. Master cylinder and wheel cylinder or calliper (oil leakage.boot kit)

6. Brake hoses and pipes (leakage, damage)
FREE

1

1
INSPECTIONS

5

6
10

12

Clean every 5,000 km. F
PERIODIC MAINTENANCE

20

24
30

36
40

48

Replace every 40,000 krr
50

60
SERVICE

60

72
AT

70

84
COST

80

96

Clean every 2,500 km or as required. Replace every 40,000 km. More frequent

replacement if dust condition is severe.

-

-

I

I

I

I

-

I

I

I

-

-

I

I
I&L

I

I

I

I

I

I

I

I

I

I

-

I

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

-

I

I

I

R

I

R

I

I

I

I

I

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

I

R

I

I

R

I

R

I

I

I

I

R

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

-

I

I

I

R

I

R

I

I

I

I

I

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

I

R

I

I

R

I

R

I

I

I

I

R

I

87

9-4

INSPECTION AND MAINTENANCE

60G-74E

Interval: This Interval should be judged

by odometer reading or months,

whichever comes first
km (x 1,000)

months

WHEEL

1. Tyres (air pressure, abnormal wear, crack, ROTATION)

2. Wheels (damage)

3. Front wheel bearings (loose, damage)

4. Rear wheel bearings (loose, damage)

FRONT AND REAR SUSPENSION

1. Suspension strut (oil leakage, damage)

2. Suspension arms and knuckle supports (loose.damage)

3. Rear spring (damage)

4. Shock absorbers (oil leakage, damage)

5. All bolts and nuts (loose)

6. Suspension arms and Tension rods

STEERING

1. Steering wheel (play, loose)

2. Power steering fluid (level, leakage)/connections

3. All rods and arms (loose, damage, wear)

ELECTRICAL

1. Battery electrolyte (level, leakage)

2. Wiring harness connection (looseness, damage)

3. Lighting system (operation, stains, damage)

4. Horn (operation)

5. System voltage

BODY

1. All chassis bolts and nuts (tighten)

2. All Latches, Hinges & Locks (function)
FREE

1

1
INSPECTIONS

5

6

Rotate and

I

-

-

I

-

-

I

-

-

I

I

I

I

-

I

I

-

-

I
I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

I

I&L
10

12
PERIODIC

20

24

inspect every 5,000

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
30

36

km

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
MAINTENANCE

40

48

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
50

60

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
SERVICE

60

72

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
AT

70

84

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
COST

80

96

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L

9-5
88

60G-74E
INSPECTION AND MAINTENANCE

BATTERY

60G-09-022E

When installing the cover, make sure that it is

positioned so that it does not cover or foul the

air valve.
60G-09-038

Batteries produce flammable hydrogen

gas. Keep flames and sparks away from

the battery or an explosion may occur.

Never smoke when working in the

vicinity of the battery .

When checking or servicing the battery,

disconnect the negative cable. Be

careful not to cause a short circuit by

allowing metal objects to contact the

battery posts and the vehicle at the

same time.
To avoid harm to yourself or damage

to your vehicle or battery, follow the

jump starting instructions in the

EMERGENCY SERVICE section of this

manual if it is necessary to jump start

your vehicle.

The level of the battery solution must be kept

between the "UPPER" and the "LOWER" level

lines at all times. If the level is found to be

below the "LOWER" level line, add distilled

water to the "UPPER" level line. You should

periodically check the battery, battery

terminals, and battery holddown bracket for

corrosion. Remove corrosion using a stiff

brush and ammonia mixed with water, or

baking soda mixed with water. After removing

corrosion, rinse with clean water.

If your vehicle is not going to be driven for a

month or longer, disconnect the cable from

the negative terminal of the battery to help

prevent discharge.

105

9-22

INSPECTION AND MAINTENANCE

60G-74E

FUSES

60G-09-024E

©. Main fuse

®. Primary fuse (Lights)

®. Primary fuse (IG)

©. Radiator fan motor fuse

©. Primary fuse (A/C, HTR)

This vehicle has three types of fuses, as

described below:

Main Fuse - The main fuse takes current

directly from the battery.

Primary Fuses - These fuses are between the

main fuse and individual fuses, and are for

electrical load groups.

Individual Fuses - These fuses are in the fuse

box and for individual electrical circuits.
MAIN FUSE / PRIMARY FUSES

80A

60A

60A

30A

60A
All Electric Load

HEAD-R, HEAD-L, TAIL/DOME,

STOP/HORN, HAZARD

CIGAR/RADIO, I.G. COIL/

METER, WIPER/WASHER,

REAR DEF, TURN/BACK,

HEATER RELAY.

RADIATOR FAN MOTOR

A/C, HTR

Main Fuse and Primary Fuses

The main fuse and primary fuses are located

in the engine compartment. If the main fuse

blows, no electrical component will function.

If a primary fuse blows, no electrical

component in the corresponding load group

will function. When replacing the main fuse or

a primary fuse, use a genuine MARUTI

replacement.

If the main fuse or a primary fuse blows,

be sure to have your vehicle inspected

by an authorized MARUTI dealer.

Always use a genuine MARUTI

replacement. Never use a substitute

such as a wire even for a temporary

repair, or extensive electrical damage

and a fire can result.
60G-09-025E

Fuse Box

The fuse boxes are located in the engine

compartment and under the driver's side of

the dashboard.

To remove the fuse box cover under the

dashboard pull off the cover.

9-23
106

EMERGENCY SERVICE

60G-74E

JACKING INSTRUCTIONS

60G-06-009

1) Park the vehicle securely on hard level

ground.

2) Apply the parking brake firmly and shift into

"R" (Reverse). Choke the front and rear wheel

diagonally opposite the wheel to be changed.

3) Switch on the hazard warning flasher if your

vehicle is in or near traffic.

4) Slacken but do not remove wheel nuts on the

wheel to be changed.

5) Position the jack vertically and raise the jack

by turning the jack handle clockwise until the

jack head recess fits the frame boss.

6) Continue to raise the jack slowly and smoothly

until the tyre clears the ground. Do not raise

the vehicle more than necessary.

10-1
63B-10-001E

70F-08-001

60G-10-001

NOTE:

Use the wheel nut wrench in combination with

jack crank to raise or lower the jack as shown

in the illustration.
Use the jack only to change wheels.

Never jack up the vehicle on an

inclined surface.

Never raise the vehicle with the jack in

a location other than under the frame

boss near the wheel to be changed.

Make sure that the jack is raised at

least 2 inches (51 mm) before it

contacts the vehicle. Use of the jack

when it is within 2 inches of being

fully collapsed may result in failure

of the jack.

Never get under the vehicle when it

is supported by the jack. t=>

116

60G-74E
EMERGENCY SERVICE

JUMP STARTING INSTRUCTIONS

60G-10-002
60G-10-003

Never run the engine when the

vehicle is supported by the jack and

never allow passengers to remain in

the vehicle.
Never attempt to jump start your

vehicle if the battery appears to be

frozen. Batteries in this condition

may explode or rupture if jump

starting is attempted.

When making jump lead

connections, be certain that your

hands and the Jump leads remain

clear from pulleys, belts, or fans.

Batteries produce flammable

hydrogen gas. Keep flames and

sparks away from the battery or an

explosion may occur. Never smoke

when working in the vicinity of the

battery.

If the booster battery you use for

jump starting is installed in another

vehicle, make sure the two vehicles

are not touching each other.

If your battery discharges

repeatedly, for no apparent reason,

have your vehicle inspected by an

authorized MARUTI dealer.

To avoid harm to yourself or damage

to your vehicle or battery, follow the

jump starting instructions below

precisely and in order. If you are in

doubt, call for qualified road service.

10-2

EMERGENCY SERVICE

60G-74E

CAUTION

Vehicle equipped with electronic fuel

injection system will not start by

pushing or towing as the fuel pump

will not work in this condition. This

starting method could also result in

permanent damage to the catalytic

converter. Use jump leads to start a

vehicle with a weak or flat battery.

60G-10-004E

When jump starting your vehicle, use the

following procedure:

1) Use only a 12 volt battery to jump start

your vehicle. Position the good 12V battery

close to your vehicle so that the jump leads

will reach both batteries. When using a

battery installed on another vehicle, DO

NOT LET THE VEHICLES TOUCH. Apply

the parking brakes fully on both vehicles.

2) Turn off all vehicle accessories, except

those necessary for safety reasons (for

example, headlights or hazard lights).
3) Make jump lead connections as follows:

a) Connect one end of the first jump lead

to the positive (+) terminal of the flat

battery.

b) Connect the other end to the positive

(+) terminal of the booster battery.

c) Connect one end of the second jump

lead to the negative (-) terminal of the

booster battery.

d) Make the final connection to an

unpainted, heavy metal part of the

engine of the vehicle with the flat

battery.

Never connect the jump lead directly

to the negative (-) terminal of the

discharged battery, or an explosion

may occur.

10-3
4) If the booster battery you are using is fitted

to another vehicle, start the engine of the

vehicle with the booster battery. Run the

engine at moderate speed.

5) Start the engine of the vehicle with the flat

battery.

6) Remove the jump leads in the exact

reverse order in which you connected

them.

118

60G-74E
EMERGENCY SERVICE

TOWING

If you need to have your vehicle towed, contact

a professional service.

CAUTION

To help avoid damage to your vehicle

during towing, proper equipment and

towing procedures must be used.

Manual Transmission

Whenever possible, your vehicle should be

towed from the front with the front wheels lifted.

If the steering and drivetrain are in good

condition, your vehicle may be towed from the

rear with the rear wheels lifted and the front

wheels on the ground. Before towing, make

sure the steering is unlocked and the

transmission is in neutral.
EMERGENCY REMEDIES

If the Starter Does Not Operate:

1) Try turning the ignition switch to the

"START" position with the headlights

turned on to determine the battery

condition. If the headlights go excessively

dim or go off, it usually means that either

the battery is flat or the battery terminal

contact is poor. Recharge the battery or

correct battery terminal contact as

necessary.

2) If the headlights remain bright, check the

fuses. If the reason for failure of the starter

is not obvious, there may be a major

electrical problem. Have the vehicle

inspected by your authorized MARUTI

dealer.

If the Engine is Flooded

If the engine is flooded with petrol, it may be

hard to start. If this happens, press the

accelerator pedal all the way to the floor and

hold it there while cranking the engine. (Do

not operate the starter motor for more than

15 seconds). Release the accelerator as soon

as the engine has started.
If the Engine Overheats

The engine could overheat temporarily under

severe driving conditions. If the engine coolant

temperature gauge indicates overheating

during driving:

1) Turn off the air conditioner, if equipped.

2) Take the vehicle to a safe place and park.

3) Let the engine run at normal idle speed

for a few minutes until the indicator is within

the normal, acceptable temperature range

between "H" and "C".

If you see or hear escaping steam, stop

the vehicle in a safe place and

Immediately turn off the engine to let it

cool. Do not open the bonnet when

steam is present. When the steam can

no longer be seen or heard, open the

hood to see if the coolant is still boiling.

If it is, you must wait until it stops

boiling before you proceed.

119

10-4

60G-74E

MODIFICATION WARNING

60G-00-004

The circle with a slash in this manual

means "Don't do this" or "Don't let this

happen".
Do not modify this vehicle. Modification

could adversely affect safety, handling,

performance, or durability and may

contravene regulations. In addition,

damage or performance problems

resulting from modification may not be

covered under warranty.
Improper installation of mobile

communication equipment such as

cellular talephones or CB (Citizen's

Band) radios may cause electronic

interference with your vehicle's ignition

system, resulting in vehicle

performance problems. Consult your

MARUTI dealer or qualified service

technician for advice on installing such

mobile communication equipment.

0-2
Copying, quoting or reproduction of any

part of this manual is not permitted without

explicit approval by MARUTI UDYOG

LIMITED.

60G-74E

WARRANTY POLICY

WARRANTY POLICY

Maruti Udyog Limited (hereinafter called "Maruti"), warrants that each

new Maruti vehicle distributed in India by Maruti and sold by an

authorised Maruti dealer will be free, under normal use and service,

from any defects in material and workmanship at the time of

manufacture SUBJECT TO THE FOLLOWING TERMS AND

CONDITIONS:

(1) Qualification:

To qualify for this warranty:

(a) The Maruti vehicle must be delivered by Maruti authorised

dealer and set-up, serviced by Maruti authorised dealer/

service station.

(b) The warranty registration card in respect of each vehicle

must be completed by the dealer at the time of delivery

of the vehicle and dealer should retain the same.

(2) Term:

The term of the warranty shall be twenty four (24) months

or 40,000 kilometers (whichever occurs first) from the date

of delivery to the first owner.

(3) Maruti's Warranty Obligation:

If any defect(s) should be found in a Maruti vehicle within the

term stipulated above, Maruti's only obligation is to repair or

replace at its sole discretion any part shown to be defective,

with a new part or the equivalent at no cost to the owner for

parts or labour, when Maruti acknowledges that such a defect

is attributable to faulty material or workmanship at the time of

manufacture. The owner is responsible of any repair or

replacements which are not covered by this warranty.
(4) Limitation:

This warranty shall not apply to:

(a) normal maintenance service required other than the three

free services, including without limitation, oil and fluid

changes, headlight aiming, fastener retightening, wheel

balancing, wheelalignment and tyre rotation, cleaning of

injectors, adjustments of carburettor, ignition timing, clutch

and valve clearance.

(b) the replacement of normal wear parts including without

limitation, bulbs, battery, tyres and tubes, spark plugs, belts,

hoses, filters, wiper blades, brushes, contact points, fuses,

clutch disc, brake shoes, brake pads, cable and all rubber

parts (except oil seal and glass run).

(c) any vehicle which has been used for competition or racing.

(d) any repairs or replacement required as a result of accidents

or collision.

(e) any defects caused by misuse, negligence, abnormal use or

insufficient care.

(f) any vehicle which has been modified or altered, including

without limitation, the installation of performance accessories.

(g) any vehicle on which parts or accessories not approved by

Maruti have been used.

(h) any vehicle which has not been operated in accordance with

the operating instructions in the Maruti Owner's Manual,

(i) any vehicle which has not received, during the warranty

term, the service inspections prescribed in the Maruti

Owner's Manual.

G) any vehicle which has been assembled, disassembled,

adjusted or repaired by other than an Maruti authorised

2-1