1999 OLDSMOBILE AURORA light

yellowblue
2-11
Personalization Features
The following list of features that are available on your
vehicle can be programmed to the driver's preference
for each transmitter.

Memory Door Locks: This feature programs your
door locks to automatically lock or unlock when
shifting in and out of PARK (P).

Security Feedback: This feature provides feedback
to the driver when the vehicle receives a command
from the remote lock control transmitter.

Delayed Locking: This feature lets the driver delay
the actual locking of the vehicle. When all doors
have been closed, the doors will lock automatically
after five seconds.

Perimeter Lighting: When the UNLOCK button on
the transmitter is pressed, the headlamps, parking
lamps, back
-up lamps and cornering lamps will turn
on in dark conditions.

Memory Seat and Mirrors: This feature programs
your driver's seat and outside mirrors to a set
memory position when the UNLOCK button on the
transmitter is pressed.
For more detailed information and programming
instructions, refer to the Index for each individual
feature listed above.Security Feedback
This personalization feature provides feedback to the
driver when the vehicle receives a command from the
remote lock control transmitter. The following modes
may be selected:
Mode 0: No transmitter response when locking or
unlocking the vehicle.
Mode 1: No transmitter response when locking;
headlamps, parking lamps, and cornering lamps flash
when unlocking the vehicle.
Mode 2: Headlamps, parking lamps, and cornering
lamps flash when locking; no response when unlocking
the vehicle.
Mode 3: Headlamps, parking lamps, and
cornering lamps flash when locking and when
unlocking the vehicle.
Mode 4: Headlamps, parking lamps, and cornering
lamps flash and horn chirps when locking; no response
when unlocking the vehicle.
Mode 5: Headlamps, parking lamps, and cornering
lamps flash and horn chirps when locking; exterior
lamps flash when unlocking the vehicle.
ProCarManuals.com

yellowblue
2-15 Remote Trunk Release Lockout
The trunk release lockout
switch in the glove box
allows you to secure items
in the trunk.
Move the trunk release lockout switch to OFF, lock the
glove box and take the key with you. Now the trunk
release, located to the right of the steering column, will
not open the trunk. However, the remote lock control
transmitter will still open the trunk.
Trunk Security Override
The remote lock control transmitter will open the trunk
even if the remote trunk release lockout switch is OFF.
Theft
Vehicle theft is big business, especially in some cities.
Although your vehicle has a number of theft
-deterrent
features, we know that nothing we put on it can make
it impossible to steal. However, there are ways you
can help.
Key in the Ignition
If you leave your vehicle with the keys inside, it's an
easy target for joy riders or professional thieves
-- so
don't do it.
With the ignition off and the driver's door open, you'll
hear a chime reminding you to remove your key from
the ignition and take it with you. Always do this. Your
steering wheel will be locked, and so will your ignition
and transaxle. And remember to lock the doors.
Parking at Night
Park in a lighted spot, close all windows and lock your
vehicle. Remember to keep your valuables out of sight.
Put them in a storage area, or take them with you.
ProCarManuals.com

yellowblue
2-16 Parking Lots
If you park in a lot where someone will be watching
your vehicle, it's best to lock it up and take your keys.
But what if you have to leave your ignition key?

If possible, park in a busy, well lit area.

Put your valuables in a storage area, like your
trunk or glove box. Be sure to close and lock the
storage area.

Close all windows.

Move the trunk release lockout switch to OFF.

Lock the glove box.

Lock all the doors except the driver's.

Then take the door key and remote lock control
transmitter with you.
Universal Theft-Deterrent
Your vehicle has a theft-deterrent alarm system. With
this system, if your ignition is off, the SECURITY light
will flash as you open the door.
This light reminds you to
activate the theft
-deterrent
system. Here's how to do it:
1. Open the door.
2. Lock the door with the power door lock switch or
remote lock control system. The SECURITY light
should come on and stay on.
3. Close all doors. The SECURITY light should go off
after about 30 seconds. The security system is not
armed until the SECURITY light is off. If the
SECURITY light stays on or flashes when the
ignition is turned on, there is a problem with the
system and the vehicle should be serviced.
ProCarManuals.com

yellowblue
2-17
If the SECURITY light comes on for one minute and then
shuts off while the ignition is on, the security system has
detected a problem. See your dealer for service.
If a door or the trunk is opened without the key or
remote lock control transmitter, the alarm will go off. It
will also go off if the trunk lock or door locks are
damaged. Your vehicle's lamps will flash and the horn
will sound for several minutes, then will go off to save
battery power.
Remember, the theft
-deterrent system won't activate if
you lock the doors with a key or manual door lock. It
only activates if you use the power door lock switch or
remote lock control transmitter. You should also
remember that you can start your vehicle with the
correct ignition key if the alarm has been set off, but this
does not shut off the alarm.
Here's how to avoid setting off the alarm by accident:

If you don't want to activate the theft
-deterrent
system, lock the door either using a key, or the
manual door lock switch.

Always unlock a door with a key, or use the remote
lock control system. Unlocking a door any other way
will set off the alarm.
If you set off the alarm by accident, unlock any door
with your key.You can also turn off the alarm by pressing UNLOCK
on the remote lock control transmitter. The alarm won't
stop if you try to unlock a door any other way.
Testing the Alarm
The alarm can be tested by following these steps:
1. From inside the vehicle, roll down the driver's
window and open the driver's door.
2. Activate the system by locking the doors with the
power door lock switch while the door is open, or
with the remote lock control transmitter.
3. Get out of the car, close the door and wait for the
SECURITY light to go out.
4. Then reach in through the window, unlock the door
with the manual door lock and open the door. This
should set off the alarm.
If the alarm does not sound when it should, but the
vehicle's lamps flash, check to see if the horn works.
The horn fuse may be blown. To replace the fuse, see
ªFuses and Circuit Breakersº in the Index.
If the alarm does not sound, or the vehicle's lamps do
not flash, the vehicle should be serviced by an
authorized service center.
ProCarManuals.com

yellowblue
2-18
PASS-Key
II
Your vehicle is equipped
with the PASS
-Key II
(Personalized Automotive
Security System)
theft
-deterrent system.
PASS
-Key II is a passive
theft
-deterrent system. It
works when you insert
or remove the key from
the ignition.
PASS
-Key II uses a resistor pellet in the ignition key
that matches a decoder in your vehicle.
When the PASS
-Key II system senses that someone is
using the wrong key, it shuts down the vehicle's starter
and fuel systems. For about three minutes, the starter
won't work and fuel won't go to the engine. If someone
tries to start your vehicle again or uses another key
during this time, the vehicle will not start. This
discourages someone from randomly trying different
keys with different resistor pellets in an attempt to make
a match.The ignition key must be clean and dry before it's
inserted in the ignition or the engine may not start. If the
engine does not start and the SECURITY light is on or
you get the CLEAN KEY...WAIT 3 MINUTES message
on the DIC, the key may be dirty or wet. Turn the
ignition off.
Clean and dry the key. Wait about three minutes and try
again. The SECURITY light may remain on during this
time. If the starter still won't work, and the key appears
to be clean and dry, wait about three minutes and try
another ignition key. At this time, you may also want to
check the fuses (see ªFuses and Circuit Breakersº in the
Index). If the starter won't work with the other key, your
vehicle needs service. If your vehicle does start, the first
ignition key may be faulty. See your dealer or a
locksmith who can service the PASS-Key II.
If you accidentally use a key that has a damaged or
missing resistor pellet, the starter won't work. The
SECURITY light will flash and the CLEAN KEY... WAIT
3 MINUTES message will appear. But you don't have to
wait three minutes before trying another ignition key.
ProCarManuals.com

yellowblue
2-19
See your dealer or a locksmith who can service the
PASS
-Key II to have a new key made.
If you're ever driving and the SECURITY light comes
on or PASS
-KEY SYSTEM FAULT appears, you will
be able to restart your engine if you turn it off. Your
PASS
-Key II system, however, is not working properly
and must be serviced by your dealer. Your vehicle is not
protected by the PASS
-Key II system.
If you lose or damage a PASS
-Key II ignition key, see
your dealer or a locksmith who can service PASS
-Key II
to have a new key made. In an emergency, call the
Oldsmobile Roadside Assistance Center at
1
-800-442-OLDS (6537). In Canada, call
1
-800-268-6800.
New Vehicle ªBreak-Inº
NOTICE:
Your vehicle doesn't need an elaborate
ªbreak
-in.º But it will perform better in the
long run if you follow these guidelines:

Don't drive at any one speed -- fast or
slow
-- for the first 500 miles (805 km).
Don't make full
-throttle starts.

Avoid making hard stops for the first
200 miles (322 km) or so. During this time
your new brake linings aren't yet broken
in. Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking
-in guideline every
time you get new brake linings.

Don't tow a trailer during break
-in. See
ªTowing a Trailerº in the Index for more
information.
ProCarManuals.com

yellowblue
2-21
RUN (D): This is the position the switch returns to after
you start your engine and release the switch. This is the
position for driving. Even when the engine is not
running, you can use RUN to operate your electrical
power accessories and to display some instrument panel
warning lights.
START (E): This position starts your engine. When the
engine starts, release the key. The ignition switch will
return to RUN for normal driving.
NOTICE:
If your key seems stuck in LOCK and you can't
turn it, be sure you are using the correct key; if
so, is it all the way in? If it is, then turn the
steering wheel left and right while you turn the
key hard. But turn the key only with your hand.
Using a tool to force it could break the key or the
ignition switch. If none of this works, then your
vehicle needs service.
Key Reminder Warning
If you leave your key in the ignition, with the engine off,
you will hear a warning chime when you open the
driver's door.
Retained Accessory Power
After you turn the ignition off and remove the key, you
will still have electrical power to such accessories as the
radio, power windows, and sunroof (option) for up to 10
minutes. But if you open a door, power is shut off.
Always leave your key in LOCK. If you leave your key
in any other position than LOCK, your battery will
discharge prematurely.
Starting Your Engine
Move your shift lever to PARK (P) or NEUTRAL (N).
Your engine won't start in any other position
-- that's a
safety feature. To restart when you're already moving,
use NEUTRAL (N) only.
ProCarManuals.com

yellowblue
2-27
Press the button on your shift lever so that it's either in
the NORMAL or POWER position. When it's in the
NORMAL position, the line on the button will be
showing. When in POWER, the line is not showing.
In the NORMAL position, the transaxle shifts at lower
engine speeds. For increased performance, you may
choose the POWER mode.
Parking Brake
Setting the parking brake: Hold the regular brake
pedal down with your right foot. Push down the parking
brake pedal with your left foot. If the ignition is on, the
parking brake indicator light will come on.Releasing the parking brake: You will need to use the
PUSH TO RELEASE parking brake pedal. Hold the
regular brake down and push the parking brake pedal
with your left foot. This will release the parking brake
pedal. When you lift your left foot, the parking brake
pedal will follow it to the released position.
If you try to drive with the parking brake on, the parking
brake indicator light stays on. The PARK BRAKE SET
message will appear in the Driver Information Center,
and a chime will sound until you release the parking
brake or recycle the ignition.
NOTICE:
Driving with the parking brake on can cause
your rear brakes to overheat. You may have to
replace them, and you could also damage other
parts of your vehicle.
If you are towing a trailer and are parking on any hill,
see ªTowing a Trailerº in the Index. That part shows
what to do first to keep the trailer from moving.
ProCarManuals.com