1999 MERCEDES-BENZ C-CLASS turn signal

• Bulbs:
High beam: HI (55 W),
low beam: H7 (55 W),
low beam: Xenon (optional)
fog lamps: HI (55 W),
turn signal lamps, parking and standing la mps, front: 2357 NA (28.5/8.3 W/30/2.2 cp),
stop lamps: 21 W/32 cp,
backup lamps: 21 W/32 cp,
turn signal lamps, rear: 21 W/32 cp,
tail, parking, side marker and standing lamp: 5 W/4 cp,
tail and parking lamp, passenger side: 21/4 W,
tail, parking arid rear fog lamp, driver's side: 21/4W,
license plate lamps: 5 W.

• Tire Pressure:
For tire pressure, refer to tire pressure label inside the fuel filler flap.

• Air Conditioner:
R-134a refrigerant and special PAG lubricant, re fer to "Technical Data" (also see Index).


ProCarManuals.com

Instrument Cluster
1. Coolant temperature gauge. See Index
2. Fuel gauge with reserve and fuel cap
placement warning lamp (yellow). See Index

3. Outside temperature indicator. See Index
4. Left turn signal indicator lamp (green)
5. ASR warning lamp (yellow) or ESP warning
lamp (yellow). See Index

6. Speedometer
7. Trip odometer, See Index


8. Main odometer, or FSS indicator. See
Index

9. Right turn signal indicator lamp (green)
10. Tachometer. See Index
11. Clock. See Index
12. Push buttons for intensity of instrument
lamps. See Index

13. Push button for resetting trip odometer.
See Index

14. Push buttons for setting clock. See Index



ProCarManuals.com

Locking and Unlocking

Unlocking:
Press transmit button
. All turn signal lamps blink once to indicate that the vehicle is unlocked.
The remote control can be programmed for two kinds of unlocking methods (see below): Selective
unlocking mode. Press transmit button
once to unlock driver's door and fuel filler flap. Press
transmit button
twice to unlock doors, fuel filler flap, and trunk. Global unlocking mode - Press
transmit button
once to unlock doors, fuel filler flap, and trunk.

Notes:
If the trunk was previously locked separately, it will remain locked (see Index). The presently active
unlocking mode (selective or global) can only be determined by unlocking the vehicle with the
remote control (see below for changing mode). The vehicle is automatically locked again, if within 40
seconds of unlocking with the remote control, neither door or trunk is opened, the electronic key is
not inserted in the steering lock, or the central locking switch is not activated.

Locking:
Press transmit button
once. All turn signal lamps blink three times to indicate that the vehicle is
locked
.
Note:
If the vehicle cannot be locked or unlocked by pressi ng the transmit button, then it may be necessary
to change the batteries in the transmitter (if ok, battery check lamp in transmitter will light briefly
when transmitting) or to synchronize the system, see Remote Control in Index.


Choosing Global or Selective Mode on Remote Control
Press and hold transmit buttons
and simultaneously for five seconds to reprogram the
remote control. Battery check lamp will blink two times indicating the completed mode change.


ProCarManuals.com

Combination Switch

1. Low beam (exterior lamp switch position
)
2. High beam (exterior lamp switch position
)
3. High beam flasher (high beam available independent of exterior lamp switch position)
4. Turn signals, right
5. Turn signals, left
To signal minor directional changes, such as changing lanes on a highway, move combination switch to
the point of resistance only and hold it there. To operate the turn signals continuously, move the combination
switch past the point of resistance (up or down). The switch is automatically canceled when the steering wheel
is turned to a large enough degree.

6. Control for windshield wiper/washer system:
Push briefly for a single wipe without adding washer fluid (use only when windshield is wet)
Push past detent point:
• windshield washer system
• optional headlamp cleaning system (only in exterior lamp positions
or ).
When the washer system is activated, the wipers also operate for a limited time.
7. Windshield wiper
0 Wiper off
I Intermittent wiping (optional rain sensor:
One initial wipe, pauses between wipes are automatically controlled by a rain sensor
monitoring the wetness of the windshield.)
II Normal wiper speed
III Fast wiper speed

Note:
The windshield washer reservoir, hoses and nozzles are automatically heated.


ProCarManuals.com

Windshield Washer Fluid Mixing Ratio
For temperatures above freezing: MB Windshield Washer Concentrate "S" and water 1 part "S" to 100 parts water
(40 ml "S" to 1 gallon water). For temperature below freezing: MB Windshield Washer Concentrate "S" and
commercially available premixed windshield washer solvent/ antifreeze 1 part "S" to 100 parts solvent (40 ml "S" to 1
gallon solvent).


Windshield Wiper Smears
If the windshield wiper smears the windshield, even during rain, activate the washer system as often as necessary.
The fluid in the washer reservoir sh ould be mixed in the correct ratio.


Blocked Windshield Wiper
If the windshield wiper becomes blocked (for example, due to snow), switch off the wiper. For safety reasons before
removing ice or snow, remove key from steering lock. Remove blockage. Activate combination switch again
(electronic key in steering lock position 1).


Turn Signal Failure
If one of the turn signals fails, the turn signal indicator system flashes and sounds at a faster than normal rate.


ProCarManuals.com

Garage Door Opener


1. Remote control transmitter located on driver side sun visor
2. Portable remote control transmitter
Warning !
When programming a garage door opener, the door moves up or down. When programming or operating
the remote control make sure there is no possib ility of anyone being harmed by the moving door.

The visor remote control is capable of operati ng up to three separately controlled objects.

Notes:
Certain types of garage door openers are incompatible wi th the integrated opener. If you should experience
difficulties
with programming the transmitter, contact your authoriz ed Mercedes-Benz dealer or call Mercedes-Benz Customer
Assistance Center (in the U.S.A. only) at 1-800-FOR- MERCedes. For operation in the USA only: This devise
complies
with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any unauthorized modification to this device could void
the user's
authority to operate the equipment.

Programming or reprogramming the remote control:
1. Turn electronic key in steering lock to position 1 or 2.
2. Press and hold one button of the remote control located on the sun visor until its control light begins to flash at a
rate of about once a second. Continue holding down the button.
Note:
The light blinks immediately if the remote control is being programmed for the first time, or if its memory was
previously erased. If you are re programming a previously used button, the light will flash afte r about 20 seconds.
3. Hold end opposite to battery of portable remote contro l against the sun visor transmitter to be programmed. While
still holding down the button on the transmitter on the sun visor, press down the button on your portable remote
control, until the sun visor remote control light starts to flash rapidly. This means that the integrated remote control
has accepted the frequency and code of the portable transmitter.
4. If you wish, repeat the procedure for each remaining button.


Operation of remote control:
1. Turn electronic key in steering lock to position 1 or 2.
2. Select and press the appropriate button (1, 2 or 3) to ac tivate the remote controlled device. The remote control
transmitter continues to send the signal as long as the button is pressed - up to 20 seconds.


Erasing the remote control memory:
1. Turn electronic key in steering lock to position 1 or 2.
2. Simultaneously holding down buttons 1 and 3 for approximatel y 20 seconds, or until the control light blinks rapidly,
will erase the code s of all three channels.


ProCarManuals.com

Flexible Service System (FSS)




The FSS permits a flexible service schedule that is dire
ctly related to the operating conditions of the vehicle.
The symbol
or appears in the main odometer field prior to the next suggested service. Depending on operating
conditions throughout the year, the nex t service is calculated and displayed in days or distance remaining. The
message is displayed for approx. 10 seconds when turning the electronic key in steering lock to position 2, or it can
be canceled manually by pressing button 0. Once the suggested term has passed, the message plus symbol
or
, preceded by a - (minus symbol) blinks, when turning t he electronic key to position 2. The FSS display can also
be called up for approx.10 seconds with display illuminated by pressing button 0 twice. Following a completed service
the Mercedes-Benz dealer sets the counter to 10 000 miles (Canada: 15 000 km) and 365 days.

The counter can also be set by any individual. To do so:
1 . Turn electronic key in steering lock to position 2.
2 . Within 4 seconds press button 0 twice.
3 . The present status for days or distance is displayed. Within 10 seconds turn electronic key in steering lock to
position 0.
4 . Press and hold button 0, while turning electronic key in steering lock to position 2 again. The present status for
days or distance is displayed once more. Continue to hold button 0 After approx. 10 seconds a signal sounds, and the
display shows 10 000 miles (Canada: 15000 km).
5 . Release button 0. If the FSS counter was inadvertently reset, have a Mercedes -Benz dealer correct it.

Notes:
When disconnecting vehicle battery for one or more days at a time, such days will not be counted. Any such days not
counted by the FSS can be added by your Mercedes-Benz de aler. The interval between services is determined by
the kind of vehicle operation. Driving at extreme speeds, and cold starts combined with short distance driving in which
the engine does not reach normal operating temperat ure, reduce the interval between services.

Model C 230:
The FSS allows for distances between 10 000 miles (Canada: 15 000 km) and 15 000 miles (Canada: 22 500 km),
or from 365 to 730 days between services.

Models C 280 and C 43 AMG:
The FSS allows for distances between 10 000 miles (Canada: 15 000 km) and 20 000 miles (Canada: 30 000 km),
or from 365 to 730 days between services. However you choose to set your reference numbers, the scheduled
services as posted in the Service Booklet must be followed to properly care for your vehicle.


ProCarManuals.com

Bulb for High Beam H1 (55 W)
Open hood.
Move retaining clamps (4) aside and remove cover (3). Pull off electrical connector (10). Unhook clamping ring
and pull out bulb together with clamping ring. Remove bulb. Insert new bulb (seating properly in cutouts of bulb
socket), mount clamping ring. Reinstall and push electr ical connector on securely. Reinstall cover and fasten
with retaining clamp (4).


Turn Signal, Parking, Side Marker and Standing Lamp
(2357 NA [28.5/8.3 W/30/2.2 cp bulb])
Open hood.
Squeeze latch (1) together and lift complete lamp assemb ly out to front of vehicle. Twist bulb socket (2)
counterclockwise and pull out. Push bulb into socket, turn counterclockwise and remove. Insert new bulb in socket
push in and twist clockwise. Reinstall bulb socket. Reinsta ll lamp assembly by sliding tabs (3) into guides (4) until
properly seated.


1. Latch for turn signal, parking, side marker, and standing lamp assembly
2. Bulb socket for turn signal, parking, side marker, and standing lamp
3. Tab
4. Guide


ProCarManuals.com