Page 76 of 432

GAUGES, METERS AND SERVICE REMINDER INDICATORS
58
(i) Open Door Warning Light
This light remains on until all the doors are completely closed.
(j) Rear Light Failure Warning Light
If this light comes on when the headlight switch is turned on
(at the first or second clickstop), it indicates that one or more
of the tail lights are burned out.
If it comes on when the brake pedal is depressed, one or more
stop lights are burned out.
Have defective bulbs replaced as soon as possible.
(k) ºTRAC OFFº Indicator/Warning Light
This light comes on when the ignition key is turned to ºONº,
and will go off after about a few seconds. This means that the
system is operating properly.
If either of the following conditions occurs, this indicates a
malfunction somewhere in the parts monitored by the
warning light system. Contact your Lexus dealer as soon as
possible to service the vehicle.
The light remains on more than a few seconds after the
ignition switch is turned on.
The light comes on while driving even if the ºTRAC OFFº
switch is not pushed.
Page 81 of 432

GAUGES, METERS AND SERVICE REMINDER INDICATORS
63
º± ±º, take your vehicle to your Lexus dealer.
(2) Driving time
(Figures with ºE/Tº)
The total time during the engine running is displayed.
When the engine is started again after the ignition is off, the
driving time is added to the previous value. Up to 99 hours
59 minutes can be displayed. When the driving time exceeds
99 hours 59 minutes, the display returns to 0 and recounting
starts.
To count from the beginning, push the ºMODE/RESETº
button for more than 1 second.
(3) Average vehicle speed(Figures with ºAVG MPHº)
The average vehicle speed is calculated and displayed
based on the total driving distance and the total driving
time with the engine running.
The displayed value is updated every 10 seconds.
To calculate from the beginning, push the ºMODE/RESETº
button for more than 1 second.
(4) Average fuel consumption(Figures with ºAVG MPGº)
The average fuel consumption is calculated and displayed
based on the total driving distance and the total fuel
consumption with the engine running.
The value is updated every 10 seconds.
To calculate from the beginning, push the ºMODE/RESETº
button for more than 1 second.
(5) Momentary fuel consumption(Figures with ºMPGº)
The momentary fuel consumption is calculated and
displayed based on the driving distance and the fuel
consumption for 3 seconds with the engine running.
The value is updated every 3 seconds.
If you are driving at low speeds just before stopping, the
accurate figure may not be shown.
For the display (1), (3), (4) or (5), º± ±º will appear\
in case
the data for calculation is not appropriate.
Page 82 of 432
GAUGES, METERS AND SERVICE REMINDER INDICATORS
64
INSTRUMENT PANEL LIGHTCONTROL
To adjust the brightness of the instrument panel lights,
turn the knob.
When the headlight switch is in the first or second click stop,
you can also adjust the brightness of the displays on the audio
and air conditioning systems using this knob.
Page 89 of 432
INTERIOR EQUIPMENT
71
Rear ashtray
To use the ashtray, pull on the lid.
When finished with your cigarette, thoroughly extinguish it
in the ashtray to prevent other cigarette butts from catching
fire. After using the ashtray, close the lid completely.
To remove the ashtray, pull it out while pressing on the snuffer
bridge to release the catch.
CAUTION
To reduce the chance of injury in case of an accident or sudden
stop while driving, always close the ashtray completely after
using.
Page 90 of 432
INTERIOR EQUIPMENT
72
GLOVEBOX
To open the glovebox door, push the lock release button.
To lock the glovebox door, insert the master key and turn
it clockwise.
With the tail lights on, the glovebox light will come on when
the glovebox door is open.
CAUTION
To reduce the chance of injury in case of an accident or a
sudden stop, always keep the glovebox door closed while
driving.
Page 92 of 432

INTERIOR EQUIPMENT
742. Bring the hand held garage door opener within about 25
mm (1 in.) of the button being programmed and push the
button on the hand held garage door opener. The signal from
the hand held garage door opener is sent to the vehicle's
opener.
3. When the frequency and code is registered, the indicator
light flashes rapidly. At this point, you can release both
buttons.
4. To program the remaining buttons, repeat steps º1º
through º3º.
If you want to replace an existing program with a new
program, select the button you want to program. Follow the
procedure from step 1.
If the transmitter has a ºrolling code featureº, it is
necessary to program the in±garage receiver after
programming
HomeLink
.
1. Locate the ºtrainingº or ºlearningº button on the
in±garage receiver and push and release this button.
Location of the button may vary by the garage door
opener manufacturer.
2. Firmly push and release the trained HomeLink
button
2 times (some garage door manufacturer may r equire you
to push the HomeLink
button up to 3 times) to complete
the process.
The garage door should now operate when the
HomeLink
button is pushed. Do not use the HomeLink
universal transmitter with any
garage door opener that lacks the safety stop and reverse
feature as required by Federal Safety Standards. This
includes any garage door opener model manufactured before
April 1, 1982.
Page 95 of 432
INTERIOR EQUIPMENT
77
CAUTION
Do not place anything else other than cups or drink±cans
on the cup holder, as such item may be thrown about in the
compartment and possibly injure people in the vehicle
during sudden braking or an accident.
To reduce the chance of injury in case of an accident or
sudden stop wh ile driving, keep the cup holder closed when
not in use.
Page 107 of 432
EXTERIOR EQUIPMENT
89
To slide open the moon roof, push the switch toward the
back. The moon roof will fully open. To stop partway,
push the switch briefly in the opposite direction or push
the ºTILTº switch.
The sun shade can be opened or closed manually. However,
if you open the moon roof, the sun shade will be opened with
the moon roof.
To close the moon roof, push the switch toward the front.
The moon roof will move while the switch is being pushed
and stop when released. However, as a precaution, it stops
partway before sliding fully closed, except when already
more than three±quarters closed. Therefore, release the
switch and then push it again to close it completely.