1999 LEXUS SC300 change

INTERIOR EQUIPMENT
75
CAUTION
When programming or operating the garage door opener,
make sure there is no one around the moving door. It is
dangerous if someone is caught.
(b) Operating the garage door opener
Push the appropriate button to activate the garage door
opener. The indicator light comes on. The garage door
opener continues to send the signal for up to 20 seconds as
long as the button is pushed.
(c) Erasing the garage door opener memory
Push and hold down the 2 outside buttons for about 20
seconds until the indicator light flashes. All memorized data
will be erased.FCC ID: CB2V94800
This device complies with FCC Rules part 15.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference that
may be received, including interference that may
cause undesired operation. WARNING: This
transmitter has been tested and complies with
FCC and DOC/MDC rules. Changes or
modifications not expressly approved by the
partly responsible for compliance could void the
user's authority to operate the device.

COMFORT ADJUSTMENT
98
Push the control switch on either side.
The amount of lumbar support will change as long as the
switch is pushed.Moving passenger's seat for rear seat entry
Lift the seatback lock release lever or press the release
pedal. The seatback will incline and the seat will
automatically slide forward.
This allows passengers to get in or out of the rear seat easily.

COMFORT ADJUSTMENT
107
Manual tilt and telescopic type
ADJUSTMENT OF STEERING WHEEL TILT
To change the steering wheel angle, hold the steering
wheel, pull up the lock release lever, tilt the steering wheel
to the desired angle and release the lever.
When the steering wheel is in a low position, it will spring up
as you release the lock release lever.
CAUTION

Do not adjust the steering wheel while the vehicle is moving.

After adjusting the steering wheel, try moving it up and
down to make sure it is locked in position.

COMFORT ADJUSTMENT
113
INSIDE REAR VIEW MIRROR
Adjust the mirror so that you can just see the rear of your
vehicle in the mirror.
Pushing the switch changes the mode between ºAUTOº
and ºDAYº.
The indicator comes on when the ºAUTOº mode is selected.
ºDAYº mode: The mirror surface is normal.
ºAUTOº mode: If the mirror detects light from the
headlights of the vehicle behind you, the mirror surface
darkens slightly to reduce the reflected light.
When the inside rear view mirror surface changes, the outside
rear view mirror surfaces will also become darker.
When the ignition key is inserted and turned on, the inside rear
view mirror always turns on in the ºAUTOº mode. When the outside air temperature is low, it may take a little
longer for the mirror to darken in response to the detection of
headlights.

COMFORT ADJUSTMENT
128
NOTICE
Do not perform any of the following changes without
consulting your Lexus dealer. Such changes can
interfere with proper operation of the seat belt
pretensioners in some cases.

Repairs on or near the front seat belt retractor
assemblies.

Modification of the suspension system.

Modification of the front end structure.

Attachment of a grille guard (bull bar, kangaroo bar,
etc.), snow plow, winches or any other equipment to
the front end.
In the following case, contact your Lexus dealer as soon as
possible:

If either front seat belt does not retract or cannot be pulled
out due to a malfunction or activation of the pretensioner.

The front seat belt retractor assembly or surrounding area
has been damaged.
SRS AIRBAGS
The SRS (Supplemental Restraint System) airbags are
designed to provide further protection for the driver and
front passenger when added to the primary protection
provided by the seat belts.
In response to a severe frontal impact, the SRS airbags
work together with the seat belts to help prevent or r educe
injury by inflating, in order to decrease the likelihood of
the driver's or front passenger's head or chest directly
hitting the steering wheel or dashboard.
The passenger airbag is activated even with no passenger in
the front seat.
Be sure to wear
your seat belt.

COMFORT ADJUSTMENT
140
NOTICE
Do not perform any of the following changes without
consulting your Lexus dealer. Such changes can
interfere with proper operation of the SRS airbag system
in some cases.

Installation of electronic items such as a mobile
two±way radio, cassette tape player or compact disc
player.

Modification of the suspension system.

Modification of the front end structure.

Attachment of a grille guard (bull bar, kangaroo bar,
etc.), snow plow, winches or any other equipment to
the front end.

Repairs made on or near the front fenders, console,
steering column, steering wheel or dashboard near the
front passenger airbag.

COMFORT ADJUSTMENT
169
1. Adjust the driver's seat, tilt and telescopic steering and
outside rear view mirrors to the desired position.
2. While pushing the ºSETº button, push button º1º or
º2º until the signal beeps.
The beep sound means that the positions are recorded in the
computer 's memory.
By repeating these two steps and pressing the remaining
button, the driving position for another driver can be
recorded.
To set a new memorized position, select the desired position
and perform step 2. The previous memory will be erased and
the new position will be set.
To make only slight changes to an already memorized
position, the easiest way is to first activate the memorized
position, then make the desired changes and perform step 2
above.Activating a memorized position

COMFORT ADJUSTMENT
170
When you push button º1º or º2º, the signal beeps and the
driving position automatically adjusts to the position
recorded for that button.
Conditions for memorized position activation

Ignition key ºONº
Selector lever in ºPº position
All parts of the memorized positions can be activated.
However, if the brake pedal is being depressed, the seat
position will not change.

Key not in ignition switch
Within 30 seconds of opening driver's door
The memorized position can be activated, except for the
tilt and telescopic steering. If any driving position memory switch is pushed while one of
the memorized driving position profiles is being activated,
the operation will stop.
To activate the system, push the desired button (º1º or º2º)
again.
The driving position memory control system cannot be
operated while the vehicle is moving.
If the vehicle's battery is disconnected, the computer's
memory
will be erased and the memorized positions will have
to be set again.