1999 Lexus ES300 Indicator

GAUGES, METERS AND SERVICE REMINDER INDICATORS
63
(k) Vehicle Skid Control System WarningLights (Vehicles with Vehicle Skid
Control System only)
These lights warn that when there is a problem
somewhere in the vehicle skid control system or traction
control system.
If the ºVSCº warning light and ºVSC OFFº indicator light
come on, have your vehicle checked by Lexus dealer as
soon as possible.
The lights will come on when the ignition key is turned to
ºONº, and will go off after about a few seconds.
If the ºVSCº warning light and ºVSC OFFº indicator light
come on, the vehicle skid control system and traction
control system do not work. However, as conventional
braking operates when applied, there is no problem to
continue your driving.
(l) ºTRAC OFFº Indicator/Warning Light (Vehicles with Traction Control
System only)
This light comes on when the ignition key is turned to
ºONº, and will go off after a few seconds. This means
that the system is operating properly.
If the light comes on or flashes, this indicates a
malfunction in the traction control system. Contact your
Lexus dealer as soon as possible to service the vehicle.
(m) Low Washer Fluid Warning Light
This light comes on when the fluid level in the tank
becomes nearly empty. F ill the tank as soon as possible.
(n) Low Fuel Level Warning Light
This light comes on when the fuel level in the tank
becomes nearly empty. F ill the tank as soon as possible.
On inclines or curves, due to the movement of fuel in the
tank, the low fuel level warning light may come on earlier
than usual.
(o) Key Reminder Buzzer
This buzzer reminds you to remove the key when you
open the driver's door with the ignition key in the ºACCº
or ºLOCKº position.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
64
How to check all the service reminder
indicators
(except the low fuel level warning light):
1. Apply the parking brake.
2. Open the door.
The following service reminder indicator should come
on. It goes off when you close the door completely.
3. Turn the ignition key to ºACCº.
The following service reminder indicator should come
on. It goes off after 6 seconds.
4. Turn the ignition key to ºONº.
The following service reminder indicators should come
on.
or

or
w069

and
The following service reminder indicators go off after a
few seconds.
or

and
w069
5. Turn the ignition key to ºSTARTº.
The following service reminder indicators should come
on.

If any service reminder indicator or warning buzzer does
not function, either the bulb is burned out or circuit is in
need of repair. Have it checked by your Lexus dealer as
soon as possible.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
65
INSTRUMENT PANEL LIGHTCONTROL
13E005
To adjust the brightness of the instrument panel
lights, turn the knob.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
66

INTERIOR EQUIPMENT
83
The
HomeLink
 has 3 buttons and can be
programmed to operate 3 separate devices.
Prepare the HomeLink
 for programming by
erasing all codes or the memorized data
programmed by the former owner. Follow the
procedure in º(c) Erasing the garage door opener
memoryº.
1. Decide which one of the 3 buttons you want to
program. Push and hold down the button for about 20
seconds until the indicator light begins to flash. While
holding this button, follow steps º2º and º3º. 2. Bring the hand held garage door opener within about
25 mm (1 in.) of the button being programmed and push
the button on the hand held garage door opener. The
signal from the hand held garage door opener is sent to
the vehicle's opener.
3. When the frequency and code is registered, the
indicator light flashes rapidly. At this point, you can
release both buttons.
4. To program the remaining buttons, repeat steps º1º
through º3º.
If you want to replace an existing program with a new
program, select the button you want to
program. Follow
the procedure from step 1.
If the transmitter has a ºrolling code featureº, it is
necessary to program the in±garage receiver after
programming HomeLink
.
1. Locate the ºtrainingº or ºlearningº button on the
in±garage receiver and push and release this
button. Location of the button may vary by the
garage door opener manufacturer.
2. Firmly push and release the trained HomeLink

button 2 times (some garage door manufacturer
may require you to push the HomeLink button up
to 3 times) to complete the process.
The garage door should now operate when the
HomeLink
 button is pushed.

INTERIOR EQUIPMENT
84Do not use the HomeLink
 universal transmitter with
any garage door opener that lacks the safety stop and
reverse feature as required by Federal Safety
Standards. This includes any garage door opener
model manufactured before April 1, 1982.
CAUTION
When programming or operating the garage door
opener, make sure there is no one around the moving
door. It is dangerous if someone is caught.
(b) Operating the garage door opener
Push the appropriate button to activate the garage door
opener. The indicator light comes on. The garage door
opener continues to send the signal for up to 20 seconds
as long as the button is pushed.
(c) Erasing the garage door opener memory
Push and hold down the 2 outside buttons for about 20
seconds until the indicator light flashes. All memorized
data will be erased. FCC ID: CB2V94800
CANADA: 1763 102 264
This device complies with FCC Rules part 15.
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference that may be received,
including interference that may cause undesired
operation. WARNING: This transmitter has
been tested and complies with FCC and
DOC/MDC rules. Changes or modifications
not expressly approved by the partly
responsible for compliance could void the
user's authority to operate the device.

EXTERIOR EQUIPMENT
102
CAUTION
Do not smoke, cause sparks or allow open flames
when refuelling. The fumes are flammable.
 When opening the cap, do not remove the cap
quickly. In hot weather, fuel under pressure could
cause injury by spraying out of the filler neck if the
cap is suddenly removed.
15E007
2. To remove the fuel tank cap, turn the cap slowly
counterclockwise, then pause slightly before
removing it. The removed cap can be stored on the
back side of the fuel filler door.
It is not unusual to hear a slight swoosh when the cap is
opened. When installing the cap, turn the cap clockwise
until you hear a click.
If the cap is not tightened securely, the malfunction
indicator lamp comes on. Make sure the cap is tightened
securely.
The indicator lamp goes off after driving several times.
If the indicator lamp does not go off, contact your Lexus
dealer as soon as possible.

COMFORT ADJUSTMENT
141
The indicator comes on when the ignition key is
turned to the ºACCº or ºONº position. It goes off
after about 6 seconds. This means the SRS is
operating properly.
The SRS warning light system monitors the airbag
sensor assemblies, front airbag sensors, inflators, seat
belt pretensioners, warning light, interconnecting wiring
and power sources. (For details, see ºService reminder
indicators and warning buzzersº on page 56 for
instructions.)
16E023