1999 LAND ROVER DEFENDER shaft

ENGINE
23
REPAIR FILTER - OIL
Service repair no - 12.60.04
Remove
1.Remove 3 bolts and remove engine acoustic
cover.
2.Release clip and disconnect breather hose from
camshaft cover.
3.Release clips and disconnect air flow meter from
air filter.
4.Disconnect multiplug from air flow meter.
5.Loosen clip screw and remove air inlet hose
from turbocharger.
6.Remove 3 bolts and remove manifold heat
shield.
7.Clean area around filter head and place a
container beneath engine.
8.Using a strap wrench, unscrew and discard filter.
Refit
9.Clean mating face of filter head.
10.Lubricate sealing ring of new filter with clean
engine oil.
11.Fit filter and tighten by hand until it seats then
tighten a further half turn.
12.Start and run engine to check for leaks.
13.Stop engine, wait a few minutes, then check oil
level.
14.Top up engine oil.
15.Position exhaust manifold heat shield and
tighten 3 bolts.
16.Position air inlet hose to turbocharger and
tighten clip screw.
17.Connect air flow meter to air filter and secure
clips.
18.Connect air flow meter multiplug.
19.Connect breather hose and secure with clip.
20.Position engine acoustic cover.
ProCarManuals.com

12ENGINE
26
REPAIR
15.Position oil pump drive sprocket and chain on to
oil pump ensuring that the’D’shape on the drive
sprocket is located on flat on the oil pump drive
shaft.
16.Clean oil pump drive sprocket retaining bolt and
apply Loctite 242 to bolt threads.
17.Fit oil pump drive sprocket retaining bolt and
tighten to25 Nm (18 lbf.ft).
18.Fit new sump gasket.See this Section.GASKET - ENGINE TO SUMP
Service repair no - 12.60.38
Remove
1.Remove battery cover.
2.Disconnect battery negative lead.
3.Remove exhaust front pipe.See MANIFOLD
AND EXHAUST SYSTEM, Repair.
4.Drain engine oil.
5.Loosen 4 bolts securing sump to gearbox bell
housing.
6.Remove 2 bolts securing centrifuge drain pipe to
sump and discard gasket.
7.Using sequence shown and noting their fitted
position, remove 20 bolts securing sump.
8.Remove sump, remove and discard gasket.
CAUTION: Do not lever between sump and
cylinder block.
ProCarManuals.com

ENGINE
27
REPAIR Refit
9.Clean sump and mating faces.
10.Apply a bead of sealant, Part No. STC 3254 to
joint faces of timing chain cover and crankshaft
rear oil seal.
11.Position new sump gasket.
CAUTION: Gasket must be fitted dry.
12.Position sump, fit bolts ensuring they are in their
correct fitted position, lightly tighten bolts.
13.Fit bolts securing sump to gearbox bell housing
and tighten to15 Nm (11 lbf.ft).
14.Using sequence shown, tighten sump bolts to25
Nm (18 lbf.ft).
15.Tighten sump to gearbox bell housing bolts to50
Nm (37 lbf ft).
16.Fit new gasket to centrifuge drain pipe and
tighten bolts to10 Nm (7 lbf.ft).
17.Fit exhaust front pipe.See MANIFOLD AND
EXHAUST SYSTEM, Repair.
18.Refill engine with oil.
19.Reconnect battery negative lead.
20.Refit battery cover.
ProCarManuals.com

12ENGINE
28
REPAIR SWITCH - OIL PRESSURE
Service repair no - 12.60.50
Remove
1.Remove fixings and remove engine acoustic
cover.
2.Release clip and disconnect breather hose from
camshaft cover.
3.Release clips and disconnect air flow meter from
air filter.
4.Disconnect multiplug from air flow meter.
5.Release clip screw and remove air inlet hose
from turbocharger.
6.Remove 3 bolts and remove exhaust manifold
heat shield.
7.Disconnect multiplug from oil pressure switch.
8.Position container below switch to catch oil
spillage.
9.Remove oil pressure switch.
Refit
10.Clean oil pressure switch threads.
11.Fit oil pressure switch and tighten to9Nm(7
lbf.ft).
12.Connect switch multiplug.
13.Position exhaust manifold heat shield and
tighten M6 bolts to10 Nm (7 lbf.ft)and M8 bolt
to25 Nm (18 lbf.ft).
14.Position air inlet hose to turbocharger and
tighten clip screw.
15.Connect air flow meter to air filter and secure
clips.
16.Connect air flow meter multiplug.
17.Connect breather hose and secure clip.
18.Fit and secure engine acoustic cover.
19.Top up engine oil.
ProCarManuals.com

12ENGINE
32
REPAIR ROTOR - CENTRIFUGE
Service repair no - 12.60.91
Remove
1.Remove 2 bolts and remove centrifuge cover.
2.Remove and discard’O’ring and rotor
Refit
3.Clean centrifuge body and cover.
4.Fit new rotor.
5.Fit centrifuge cover using new’O’ring and
tighten bolts to9 Nm (7 lbf.ft).OIL SEAL - TIMING COVER
Service repair no - 12.65.05
Remove
1.Remove crankshaft pulley.See this Section.
2.PositionLRT-12-092into crankshaft front oil seal
and discard seal.
Refit
3.Using a lint free cloth, thoroughly clean oil seal
recess and the running surface on crankshaft
pulley.
4.Position new seal into timing chain housing. Drift
seal into place usingLRT-12-156.
5.RemoveLRT-12-156.
6.Fit crankshaft pulley.See this Section.
ProCarManuals.com

ENGINE
33
REPAIR TIMING CHAIN AND SPROCKETS
Service repair no - 12.65.13
Remove
1.Remove crankshaft front oil seal.See this
Section.
2.Remove cylinder head gasket.See this
Section.
3.Remove sump gasket.See this Section.
4.Release clip securing vacuum pump drain hose
to timing chain cover.
5.Remove 8 bolts securing timing chain cover.
6.Remove cover.
7.Remove timing chain and camshaft sprocket.
8.Remove 2 bolts and remove timing chain fixed
guide.
9.Remove bolt and remove timing chain adjustable
guide.
10.Remove bolt securing oil pump drive sprocket.
11.Remove crankshaft sprocket, oil pump drive
chain and sprocket.
12.Remove bolt and remove timing chain lubrication
jet.
Refit
13.Clean timing chain lubrication jet.
14.Fit lubrication jet and tighten bolt to10 Nm (7
lbf.ft).
15.Clean oil pump drive sprocket bolt threads.
16.Clean timing sprockets and chain guides.
17.Ensure that crankshaft is set to TDC firing No. 1
cylinder.
18.Fit oil pump drive chain to crankshaft sprocket
and fit sprocket to crankshaft.
19.Fit sprocket to oil pump.
20.Apply Loctite 242 to oil pump sprocket bolt
threads and tighten bolt to25 Nm (18 lbf.ft).
21.Fit timing chain fixed guide and tighten M10 bolt
to45 Nm (34 lbf.ft)and M6 bolt to10 Nm (7
lbf.ft).
22.Fit timing chain adjustable guide and tighten bolt
to25 Nm (18 lbf.ft).
ProCarManuals.com

12ENGINE
34
REPAIR
23.Fit camshaft sprocket to timing chain with timing
mark between the 2 bluelinks.
24.Fit timing chain to crankshaft sprocket aligning
blue link to timing mark.
25.Clean timing cover and mating face.
26.Apply an even film of sealant, Part No. STC
4600 to timing cover and spread to an even film
using a roller.
CAUTION: Assembly and bolt tightening
must be completed within 20 minutes of
applying sealant.
27.With assistance, fit timing cover, connect
vacuum pump drain hose and working
progressively, tighten bolts to27 Nm (20 lbf.ft).
28.Secure vacuum hose clip.
29.Fit cylinder head gasket.See this Section.
30.Fit sump gasket.See this Section.
31.Fit crankshaft front oil seal.See this Section.
ProCarManuals.com

ENGINE
1
OVERHAUL GASKET - INLET MANIFOLD
Service repair no - 30.15.08.01
Remove
NOTE: The following procedure covers
both EU3 and non EU3 engines
NOTE: EU3 Engine in main illustration, Pre
EU3 condition shown in inset.
1.Remove and discard 2 Allen screws securing
EGR pipe or EGR cooler to exhaust manifold.
2.Remove bolt securing EGR pipe to cylinder
head, (if fitted)
3.Disconnect multiplug from IAT and MAP sensor.
4.Remove 4 bolts securing fuel cooler to inlet
manifold. and remove cooler.
5.Remove bolt securing engine dipstick tube to
camshaft carrier.
6.Release and remove engine dipstick tube.
7.Remove’O’ring from dip stick tube.
8.Disconnect 4 leads from glow plugs.
9.Remove 2 nuts and 8 bolts and remove inlet
manifold.
10.Remove manifold gasket.Refit
1.Clean inlet manifold and mating face, clean
mating faces of EGR pipe, exhaust manifold and
EGR cooler (if fitted).
2.Fit new gasket.
3.Position inlet manifold and working from the
centre outwards, fit inlet manifold nuts and bolts
and tighten to25 Nm (18 lbf.ft).
4.Connect glow plug leads.
5.Clean engine dipstick tube.
6.Fit new’O’ring to dipstick tube.
7.Fit engine dipstick tube to camshaft carrier and
tighten bolt to10 Nm (7 lbf.ft).
8.Position fuel cooler and tighten bolts to25 Nm
(18 lbf.ft).
9.Connect multiplug to IAT and MAP sensor.
10.Position EGR pipe or EGR cooler to exhaust
manifold and using new Allen screws tighten to
10 Nm (7 lbf.ft).
11.Fit EGR pipe clamp to cylinder head, (if fitted)
and tighten bolt to10 Nm (7 lbf.ft).
ProCarManuals.com