1999 LAND ROVER DEFENDER oil filter

12ENGINE
30
REPAIR Refit
10.Clean oil cooler and mating faces.
11.Fit oil pressure switch and tighten to9Nm(7
lbf.ft).
12.Position oil cooler using a new gasket and
tighten bolts to25 Nm (18 lbf.ft).
13.Position oil filter adaptor, fit new gasket and
tighten bolts to25 Nm (18 lbf.ft).
14.Position oil filter element hand tight then a
further half turn.
15.Position coolant hose to oil cooler and secure
clip.
16.Position coolant pipe and tighten clutch housing
bolt to50 Nm (37 lbf.ft).
17.Connect oil pressure switch multiplug.
18.Fit centrifuge assembly.See this Section.
19.Refill cooling system.See COOLING SYSTEM,
Adjustment.
20.Top up engine oil.CENTRIFUGE ASSEMBLY
Service repair no - 12.60.90
Remove
1.Remove fixings and remove underbelly panel.
See CHASSIS AND BODY, Repair.
2.Remove 2 bolts securing centrifuge drain pipe to
engine sump and discard gasket.
3.Remove turbocharger.See FUEL SYSTEM,
Repair.
Models with air conditioning only
4.Remove auxiliary drive belt.See
ELECTRICAL, Repair.
5.Remove 4 bolts securing compressor and move
to one side.
ProCarManuals.com

ENGINE
11
OVERHAUL
23.Remove 3 bolts and remove fuel connector
block from cylinder head.
24.Remove and discard gasket,’O’ring and fuel
filter.
25.Remove spacer block and gasket (if fitted).Cylinder head and camshaft carrier - cleaning
1.Thoroughly clean cylinder head mating faces,
ensure oil and coolant passages are clear and
bolt holes are clean and dry.
CAUTION: Take care to ensure that EUI
drillings are clear.
2.Using suitable solvent, remove all traces of
sealant and gasket material.
CAUTION: Do not use metal scrapers.
3.Remove all traces of oil from camshaft bearings
and journals.
4.Clean glow plug threads.
Cylinder head - Inspection
1.Check core plugs for signs of leakage and
corrosion, seal replacement plugs with Loctite
243.
2.Check cylinder head for warping across centre
and from corner to corner.
Maximum cylinder head warp =0.1 mm (0.004
in).
CAUTION: Cylinder heads may not be
refaced, replace the head assembly if
warping exceeds the limit given.
ProCarManuals.com

ENGINE
19
OVERHAUL 16.Lubricate finger followers with engine oil.
17.Fit finger followers ensuring they are in their
original fitted order.
18.Lubricate cams and bearing journals on
camshaft, cylinder head and camshaft carrier
with engine oil.
19.Position camshaft in cylinder head with the
timing pin hole in the vertical position.
20.Apply an even film of sealant, Part No. STC
4600 to camshaft carrier face and spread to an
even film using a roller.
CAUTION: Ensure sealant does not block
oilways (arrowed) or contaminate
camshaft bearings. Assembly and bolt
tightening must be completed within 20 minutes
of applying sealant.
21.Fit camshaft carrier ensuring it is correctly
located on dowels.
22.Fit and lightly tighten new camshaft carrier bolts.
23.Using sequence shown, progressively tighten
bolts to25 Nm (18 lbf.ft).
24.Lubricate a new camshaft rear oil seal with
engine oil, fit seal using a suitable mandrel.
25.Position rocker shaft on camshaft carrier,
ensuring rocker shaft is located on dowel.
26.Fit new rocker shaft retaining bolts and working
from the centre outwards, tighten bolts
progressively to32 Nm (24 lbf.ft).27.Lubricate a new’O’ring with engine oil and fit to
injector harness multiplug.
28.Fit injector harness and connect multiplugs.
29.Clean fuel connector block and mating face.
30.Lubricate a new fuel filter’O’ring with engine oil.
31.Fit new fuel filter,’O’ring and gasket.
CAUTION: Gasket must be fitted dry.
32.Fit fuel connector block spacer and gasket (if
fitted).
33.Fit fuel connector block, fit bolts and tighten to
25 Nm (18 lbf.ft).
34.Clean glow plugs.
35.Fit glow plugs to cylinder head and tighten to16
Nm (12 lbf.ft).
36. Engine Serial No. Prefixes 15P to 19P:-
Lubricate new’O’rings with engine oil and fit to
spill return pipe; fit pipe and tighten connectors
to20 Nm (15 lbf.ft).
37.Fit new cylinder head gasket.See this Section.
CAUTION: Ensure that the fuel injector
rockers are adjusted following the
procedures given in Gasket - Cylinder
head - Refit.
ProCarManuals.com

12ENGINE
20
OVERHAUL GASKET - ENGINE SUMP
Service repair no - 12.60.38.01
Remove
1.Remove 2 bolts securing centrifuge oil drain pipe
to sump, remove and discard gasket.
2.Using sequence shown and noting their fitted
positions, remove 20 bolts securing sump to
cylinder block.
3.Remove sump, remove and discard gasket.
CAUTION: Do not lever between sump and
cylinder block.Refit
1.Clean sump and mating faces, ensure bolt holes
in cylinder block are clean and dry.
2.Using suitable solvent, remove all traces of
sealant from joint faces of timing chain cover and
crankshaft rear oil seal housing.
3.Clean centrifugal filter oil drain pipe and mating
faces.
4.Apply a bead of sealant, Part No. STC 3254 to
joint faces of timing chain cover and crankshaft
rear oil seal housing.
CAUTION: Assembly and bolt tightening
must be completed within 20 minutes of
applying sealant.
5.Position new sump gasket.
CAUTION: Gasket must be fitted dry.
6.Position sump, fit and lightly tighten bolts
ensuring they are in their original fitted positions.
ProCarManuals.com

ENGINE MANAGEMENT SYSTEM
27
DESCRIPTION AND OPERATION The turbocharger is exposed to extremely high operating temperatures (up to 1000°C, 1832°F) because of the
hot exhaust gases and the high speed revolution of the turbine (up to 15,000 rev/min). In order to resist wear of
the turbine bearings a flow of lubrication oil is supplied from the engine lubrication system to keep the bearings
cool. Oil is supplied from a tapping at the front of the full-flow filter adaptor housing via a metal pipe with banjo
connections. Oil is returned to the sump via a metal pipe which connects to the cylinder block at a port below the
turbocharger assembly.
A heatshield is attached to the LH side of the engine to protect adjacent components from the heat generated at
the turbocharger. The heatshield is attached to the engine by 2 bolts. An additional bolt attaches the heatshield to
the turbocharger casting.
The ECM controls the amount of boost pressure the engine receives by way of the turbocharger. When full boost
is reached a control signal is sent to the wastegate modulator, and a vacuum is applied to the wastegate valve.
The wastegate valve opens, bypassing some of the exhaust gases away from the turbine to be output to the
exhaust system.
The engine should be allowed to idle for 15 seconds following engine start up and before the engine is switched
off to protect the turbocharger by maintaining oil supply to the turbine bearings.
INTERCOOLER
The intercooler is an air-to-air heat exchanger which lowers the intake air temperature to obtain a higher air
density for better combustion efficiency. The intercooler receives compressed air from the turbocharger via a
metal pipe. It cools the intake air via the intercooler matrix and delivers it to the intake manifold by means of a
rubber hose which connects between the intercooler outlet and the intake manifold. The rubber hose is connected
to ports at each end by metal clips.
The intercooler is located at the front of the engine bay, forward of the radiator.
ProCarManuals.com

19FUEL SYSTEM
4
DESCRIPTION AND OPERATION Fuel Pump
The fuel pump assembly comprises a top cover which locates the electrical connector, and four fuel pipe
couplings. The top cover is attached to a plastic cup shaped housing and retained on three sliding clips. Two coil
springs are located between the cover and the housing and ensure that the fuel pump remains seated positively at
the bottom of the tank when installed.
The housing locates the two stage fuel pump and also the fuel gauge sender unit. The lower part of the housing is
the swirl pot which maintains a constant level of fuel at the fuel pick-up. A coarse filter is located in the base of the
housing and prevents the ingress of contaminants into the pump and the fuel system from the fuel being drawn
into the pump. A fine filter is located in the intake to the low pressure stage to protect the pump from
contaminants. Flexible pipes connect the couplings on the top cover to the pump.
A non-return valve is located in the base of the housing. When the fuel tank is full, fuel pressure keeps the valve
lifted from its seat, allowing fuel to flow into the swirl pot. As the tank level reduces, the fuel pressure in the tank
reduces causing the valve to close. When the valve is closed, fuel is retained in the swirl pot, ensuring that the
swirl pot remains full and maintains a constant supply to the fuel pump.
The two stage pump comprises a high and low pressure stage. The low pressure stage draws fuel from the swirl
pot through a filter. The low pressure stage pumps fluid at a pressure of 0.75 bar (10.9 lbf.in) and a flow of 30
litres/hour (8 US Gallons/hour) to the fuel filter. A proportion of the fuel from the low pressure stage also passes,
via a restrictor, through a jet pump which keeps fuel circulating in the swirl pot. The high pressure stage draws the
low pressure fuel from the fuel filter and pressurises it to a pressure of 4.0 bar (58 lbf.in). The pressurised fuel is
then passed from the pump to the injectors at a flow of 180 litres/hour (47.6 US Gallons/hour). A fuel pressure
regulator is located at the rear of the engine and ensures that the delivery pressure remains at 4.0 bar (58 lbf.in)
by controlling the amount of fuel returning to the fuel tank.
The fuel pump has a maximum current draw of 15 Amps at 12 Volts and is supplied a feed (C0114-1) from the fuel
pump relay (C0730-2) on a white/purple wire.
Fuel Gauge Sender
The fuel gauge sender unit comprises a rotary potentiometer operated by a float. The float rises and falls with the
fuel level in the tank and moves the potentiometer accordingly.
A feed is supplied to the fuel gauge sender (C0114-1) by the fuel pump relay (C0730-2) on a purple/white then
white/purple wire. The sender is earthed (C0114-3) on a slate/black wire via header 287. The output voltage
(C0114-2) from the sender to the instrument pack (C1061-3) varies in relation to the fuel level. This output voltage
is connected to the fuel gauge C1054-2). The fuel gauge receives a battery voltage input (C1054-3) on a
white/green wire. This is compared with the output voltage from the potentiometer. The difference between the two
voltages determines the deflection of the fuel gauge pointer.
ProCarManuals.com

FUEL SYSTEM
5
REPAIR TURBOCHARGER
Service repair no - 19.42.01
Remove
1.Remove battery cover.
2.Disconnect battery negative lead.
3.Remove 3 bolts and remove engine acoustic
cover.
4.Release clip and disconnect breather hose from
camshaft cover.
5.Release clips and disconnect air flow meter from
air filter.
6.Disconnect multiplug from air flow meter.
7.Loosen clip screw and remove air inlet hose
from turbocharger.
8.Remove 3 bolts and remove exhaust manifold
heat shield.
9.Release clip and disconnect vacuum hose from
turbocharger wastegate.
10.Loosen clip screw and release air outlet hose
from turbocharger.
11.Remove turbocharger oil feed banjo bolt and
discard sealing washers.
12.Remove 3 nuts and release exhaust front pipe
from turbocharger and discard gasket.
13.Remove 3 nuts securing turbocharger to exhaust
manifold.
14.Loosen and unscrew turbocharger drain pipe
union from cylinder block.
15.Remove turbocharger and discard gasket.
16.Remove 2 bolts and remove turbocharger oil
drain pipe. Discard gasket.
ProCarManuals.com

19FUEL SYSTEM
6
REPAIR Refit
17.Clean turbocharger and oil drain pipe mating
faces.
18.Using a NEW gasket, fit turbocharger drain pipe
and tighten bolts to10 Nm (7 lbf.ft).
19.Using a new gasket fit turbocharger to exhaust
manifold and tighten nuts to30 Nm (22 lbf. ft).
20.Position oil drain pipe to cylinder block and
tighten union.
21.Using new gasket, align exhaust front pipe and
tighten nuts to30 Nm (22 lbf.ft)
22.Fit banjo bolt to oil feed pipe using new sealing
washers and tighten to25 Nm (18 lbf.ft).
23.Position air outlet hose to turbocharger and
tighten clip screw.
24.Position and secure vacuum hose to
turbocharger wastegate.
25.Position exhaust manifold heat shield and
tighten M6 bolts to9 Nm (7 lbf.ft)and M8 bolt to
25 Nm (18 lbf.ft).
26.Position air inlet hose to turbocharger and
tighten clip screw.
27.Connect air flow meter to air filter and secure
clips.
28.Connect air flow meter multiplug.
29.Connect breather hose and secure clip.
30.Fit engine acoustic cover and secure with bolts.
31.Reconnect battery negative lead.
32.Fit battery cover.FILTER ASSEMBLY - AIR
Service repair no - 19.10.01
Remove
1.Loosen clip screw and release intake hose from
air filter.
2.Release 2 clips securing air flow meter.
3.Release air flow meter from air filter cover and
position aside.
4.Disconnect multiplug from AAP sensor.
5.Release air filter from 3 grommets, remove
assembly and discard’O’ring.
6.Remove 2 screws, remove AAP sensor and
discard’O’ring.
ProCarManuals.com