1999 LAND ROVER DEFENDER steering

MAINTENANCE
21
MAINTENANCE STEERING BALL JOINTS
1.Check for wear in joints by moving ball joint up
and down vigorously. If free movement is
apparent, fit a new joint assembly.
2.Check condition of steering ball joints paying
particular attention to dust covers.
NOTE: Any requirement to replace the
steering ball joints should be advised to
the customer as this will incur additional
labour and/or material cost and should not be
carried out without the authorisation of the
customer.
NOTE: Ball joints are lubricated for life
during manufacture and require no further
lubrication unless the rubber boot has
been dislodged or damaged. All joints should be
checked at specified service intervals, but more
frequently if vehicle is used under arduous
conditions.
ProCarManuals.com

MAINTENANCE
23
MAINTENANCE ENGINE AND TRANSMISSION MOUNTINGS
1.Check condition of front LH engine mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
2.Check condition of front RH engine mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
3.Check condition of rear LH gearbox mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
4.Check condition of rear RH gearbox mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.ROAD TEST
There are two purposes for conducting a road test.
Firstly, to ensure the work completed within the
dealership meets the standards required as layed
down by dealership processes. Secondly, for a skilled
technician to assess the general condition of the
vehicle and report any conditions that the customer
should be made aware of.
CAUTION: Two wheel roller tests must not
be carried out. Four wheel roller tests
must be restricted to 3 mph (5 kph).
1.Check for correct operation of starter switch.
Ensure the engine starts in a correct manner.
Leave the engine running.
2.With vehicle stationary, turn steering from lock to
lock. Check for smooth operation and ensure
there is no undue noise from the power steering
pump or drive belt.
3.Depress clutch and select all gears in turn.
Check for smooth notch free engagement.
4.Drive vehicle on a short road test. Check all
vehicle systems for correct operation. Pay
particular attention to:
Engine noise
Gearbox noise
Suspension noise
Body noise
Braking system operation
Gear selection
Engine performance
5.Check for correct operation of all instruments
and warning devices where practical.
6.After road test, carry out a final inspection of the
vehicle on vehicle ramps.
7.Check all underbonnet fluid levels and top-up if
necessary.
ProCarManuals.com

FRONT AXLE AND FINAL DRIVE
1
REPAIR FRONT AXLE ASSEMBLY
Service repair no - 54.10.01
Remove
WARNING: Remove and refit of axle
requires a further two persons to steady
axle when lowering or repositioning axle.
1.Support chassis front.
2.Remove road wheels.
3.Support axle weight with hydraulic jack.
4.Remove radius arms to chassis frame nuts.
5.Disconnect steering damper from track rod.
Using a extractor remove track rod links from
swivel pin arms.
6.Remove four nuts and bolts securing radius
arms to axle bracket.
7.Remove radius arms.
8.Remove bolts securing brake hose brackets .
Refit bolts to prevent oil leakage.
9.Remove bolts from brake calipers and tie to one
side.
10.Remove nuts and washers securing shock
absorbers to axle.
11.Disconnect drag link from swivel pin housing
arm.
12.Remove two nuts and bolts securing panhard
rod to axle bracket. Lift rod clear of axle.
13.Mark for reassembly drive shaft flanges.
Remove four nuts and bolts, tie propeller shaft to
one side.
14.Release axle ventilation pipe banjo and lower
axle assembly. Remove road springs.
15.Disconnect anti-roll bar linkSee FRONT
SUSPENSION, Repair. Anti-roll bar ball.
16.Remove axle assembly.
Refit
17.Position axle under vehicle, supporting left side
of axle, and fit anti-roll bar linksSee FRONT
SUSPENSION, Repair. Anti-roll bar links.
18.Fit propeller shaft. Tighten bolts to47 Nm (35
lbf/ft).
19.Fit panhard rod to axle bracket. Tighten bolts to
88 Nm (65 lbf/ft).
20.Fit drag link to swivel pin arm. Tighten fixings to
40 Nm (30 lbf/ft).
21.Fit shock absorbers to axle.
22.Fit brake calipers. Tighten bolts to82 Nm (60
lbf/ft).
23.Tighten upper swivel pin bolts to78 Nm (58
lbf/ft).
24.Fit radius arms to axle brackets. Tighten bolts to
197 Nm (145 lbf/ft).
25.Fit steering damper to track rod.
26.Fit radius arms to chassis side member. Tighten
fixings to197 Nm (145 lbf/ft).
27.Tighten track rod end to40 Nm (30 lbf/ft)and fit
new split pin.
28.Remove chassis supports, fit road wheels and
tighten to correct torque:
Alloy wheels -130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)
ProCarManuals.com

54FRONT AXLE AND FINAL DRIVE
6
OVERHAUL 38.Place retaining plate, joint washer and oil seal
over axle flange ready for assembly.
39.Fit swivel bearing housing to axle flange with 7
bolts. Tighten to73 Nm (54 lbf/ft).
40.Grease and fit upper and lower swivel pin taper
roller bearings.
41.Position swivel pin housing over swivel bearing
housing.
42.Coat joint washer both sides with sealing
compound and position on lower swivel pin.
43.Loosely fit brake shield bracket plus lower swivel
pin with lug outboard to swivel pin housing.
44.Loosely fit top swivel pin plus existing shims and
brake hose bracket to swivel pin housing.
45.Apply Loctite 270 or equivalent to lower swivel
pin bolts.25 Nm (18 lbf/ft),bend over lock tabs.
46.Tighten top swivel pin bolts to65 Nm (48 lbf/ft).
Check and adjust preload on bearings
NOTE: Swivel housing oil seal and axle
should not be fitted.
47.Attach a spring balance to track rod ball joint
bore and pull balance to determine effort
required to turn swivel pin housing.
Resistance, once initial inertia has been
overcome, should be1.16 to 1.46 kg.Adjust by
removing or adding shims to top swivel pin.
48.When setting is correct remove top swivel bolts,
apply Loctite 270 or equivalent. Refit bolts and
tighten to65 Nm (48 lbf/ft),and bend over lock
tabs.
49.Apply recommended grease between lips of
swivel oil seal.50.Fit oil seal, joint washer and retaining plate with
7 bolts and spring washers. Tighten to11 Nm (8
lbf/ft).
51.Fit tie rod and drag link and secure with new
cotter pins. Tighten fixing to40 Nm (30 lbf/ft).
52.Fit brake disc shield.
53.Loosely fit lock stop bolt and nut.
54.Apply a recommended grease between lips of
swivel housing oil seal.
55.Secure oil seal with retaining plate and securing
bolts. Tighten to11 Nm (8 lbf/ft).
56.Fit track-rod and drag link and secure with new
cotter pins.
57.Loosely fit lock stop bolt for later adjustment.
58.Fit brake disc shield.
Fit driveshaft and stub axle
59.Insert axle shaft, and when differential splines
are engaged, push assembly in fully.
CAUTION: Take care not to damage axle
shaft oil seals.
60.Place a new joint washer in position on swivelpin
housing to stub axle mating face. Coat threads
of stub axle bolts with Loctite 270.
61.Fit stub axle with flat at 12 O’clock position.
CAUTION: Ensure that constant velocity
joint bearing journal is butted against
thrust ring on stub axle before stub axle is
secured.
62.Place mud shield in position and secure stub
axle to swivel pin housing with 6 bolts and
tighten evenly to65 Nm (48 lbf/ft).
63.Fit brake jump hoses to brake jump hose
bracket.
64.Fit complete front hub assemblySee FRONT
SUSPENSION, Repair. Front hub bearings.
65.Check swivel pin housing oil drain plug is fitted.
66.Fill swivel assembly to correct level, with new oil
See MAINTENANCE , Under vehicle
maintenance.
NOTE: On later vehicles fill swivel pin
housing with 0.33 Litres of Molytex EP 00
grease.
67.Set steering lock stop boltsSee STEERING,
Adjustment. Steering lock stops.
ProCarManuals.com

57 - STEERING
CONTENTS
Page
REPAIR
STEERING COLUMN - UPPER - Td5 1.................................................................
ProCarManuals.com

STEERING
1
REPAIR STEERING COLUMN - UPPER - Td5
Service repair no - 57.40.01
Remove
1.Ensure road wheels and steering wheel are set
in the straight ahead position.
2.Loosen 2 clips securing air inlet pipe between
turbo and inlet air filter.
3.Remove air inlet pipe.
4.Mark relationship between the upper steering
column and the lower steering column universal
joint.
5.Remove bolt securing upper column to lower
column universal joint.
6.Remove steering colum nacelle.See this
Section.
7.Remove instrument pack.See
INSTRUMENTS, Repair.
8.Disconnect 3 column switch multiplugs.
9.Loosen column switch clamping screw.
10.Remove column switch assembly from steering
column.
11.Disconnect 4 Lucars from rear of ignition switch.
NOTE: Take note of Lucars correct fitted
position. Details can also be found in the
Electrical Reference Library.
12.Remove passive coil.See ELECTRICAL,
Repair.
13.Drill out 2 shear bolts securing ignition barrel to
column.
14.Remove ignition barrel.
ProCarManuals.com

57STEERING
2
REPAIR 15.Remove brake servo.See BRAKES, Repair.
16.Release ABS modulator multiplug from side of
brake pedal box.
17.Release mat from underside of fascia to gain
access to brake pedal box mounting bolts.
18.Remove 6 bolts securing brake pedal box to
bulkhead.
19.Disconnect 2 brake pedal switch Lucars.
20.Carefully remove brake pedal box assembly and
collect gasket.
21.Remove bolt securing column upper tie bar to
column.
22.Remove 2 bolts securing upper column to lower
mounting bracket.
23.Remove 2 bolts securing 2 halves of column
upper clamp.
24.Remove 2 bolts securing column upper clamp to
mounting bracket.
25.Remove column upper clamp and collect rubber
packing.
26.Remove 2 bolts securing column upper
mounting bracket to bulkhead.
27.Release upper column from lower column and
manouvre mounting bracket and upper column
assembly from vehicle.
28.Remove mounting bracket from column.
ProCarManuals.com

STEERING
3
REPAIR Refit
NOTE: The steering column is a
non-servicable component and can only
be serviced as a complete assembly.
29.Fit mounting bracket to column and manouvre
assembly into position.
NOTE: Ensure marks on upper and lower
columns are aligned.
30.Loosely fit bolts securing mounting bracket to
bulkhead.
31.Fit upper clamp and rubber packing to column.
32.Loosely fit bolts securing upper clamp to
mounting bracket.
33.Loosely fit bolts securing 2 halves of upper
clamp.
34.Loosely fit bolts securing column lower mounting
bracket.
35.Fit bolt securing upper tie bar to steering column
and tighten to22 Nm (16 lbf.ft).
36.Tighten mounting bracket to bulkhead bolts,
clamp bolts, and lower mounting bolts.
M6 bolts =9 Nm (6 lbf.ft)
M8 bolts =22 Nm (16 lbf.ft)
37.Manouvre brake pedal box assembly and NEW
gasket into position in vehicle.
38.Tighten bolts securing brake pedal box to
bulkhead to25 Nm (18 lbf.ft)
39.Connect brake pedal switch Lucars.
40.Reposition mat to underside of fascia.
41.Secure ABS modulator multiplug to side of brake
pedal box.
42.Fit brake servo.See BRAKES, Repair.
43.Fit ignition switch to steering column, ensuring
inner shaft slot aligns with steering lock plunger.
44.Evenly tighten clamp bolts, but DO NOT shear at
this stage.
45.Temporarily fit steering wheel and check for
correct operation of switch and lock.
46.Remove steering wheel.
47.Fully tighten ignition switch bolts until heads
shear.48.Connect Lucars to rear of ignition switch.
49.Fit passive coil to ignition switch and connect
multiplug.
50.Fit switch assembly to steering column and
tighten clamping screw.
51.Connect column switch multiplugs.
52.Fit instrument pack.See INSTRUMENTS,
Repair.
53.Fit steering column nacelle.See this Section.
54.Fit bolt securing upper column to lower column
universal joint and tighten to25 Nm (18 lbf.ft).
55.Fit air inlet pipe between turbo and inlet air filter
and secure with clips.
ProCarManuals.com