1999 LAND ROVER DEFENDER alternator

12ENGINE
6
OVERHAUL 14.Clean fixed guide Allen screw and apply Loctite
242 to screw threads.
15.Fit fixed timing chain guide Allen screw and
tighten to25 Nm (18 lbf.ft).
16.Clean timing chain tensioner and fit new sealing
washer.
17.Fit timing chain tensioner and tighten to45 Nm
(33 lbf.ft).
18.Tighten camshaft sprocket bolts to36 Nm (27
lbf.ft).
19.Remove toolLRT-12-058from camshaft.
20.Lubricate a new’O’ring with engine oil and fit to
camshaft sprocket access plug.
21.Fit camshaft sprocket access plug.
22.Clean alternator/vacuum pump oil feed hose
union.
23.Lubricate a new’O’ring with engine oil and fit to
alternator/vacuum pump hose union.
24.Fit and tighten alternator/vacuum pump oil hose
union to10 Nm (7 lbf.ft).
25.Fit bolt securing alternator strap bracket to
cylinder head and tighten to25 Nm (18 lbf.ft).
26.Connect multiplugs to ECT sensor and EUIs.
CAUTION: Following cylinder head
overhaul, it will be necessary, before
fitting the camshaft cover, to adjust the
fuel injector rockers using the following
procedures:
27.Rotate engine clockwise until No. 1 EUI lobe is
at full lift.
28.Tighten No.1 rocker adjusting screw until the EUI
plunger is felt to’bottom out’.
29.Loosen rocker adjusting screw 1 complete turn
to give EUI plunger the required bump clearance
and tighten rocker adjusting screw locknut to16
Nm (12 lbf.ft).
CAUTION: Ensure screw does not turn as
locknut is tightened.30.Carry out above procedures for the remaining 4
rocker arms.
31.After completion of rocker adjustment, slowly
rotate engine clockwise 2 complete turns by
hand to ensure that no EUI’s are bottoming out
on their plungers.
32.Clean camshaft cover and mating face.
33.Fit new sealing washers and isolators as
necessary to camshaft cover.
34.Fit new camshaft cover gasket to cover.
CAUTION: Gasket must be fitted dry.
35.Fit camshaft cover to camshaft carrier, fit bolts
and working from the centre outwards, tighten
bolts to10 Nm (7 lbf.ft).
36.Fit inlet manifold gasket.See MANIFOLD AND
EXHAUST SYSTEM, Repair.
37.Fit exhaust manifold gasket.See MANIFOLD
AND EXHAUST SYSTEM, Repair.
38. EGR cooler fitted:-Position EGR pipe to cooler,
fit new Allen screws and tighten to10 Nm (7
lbf.ft).
ProCarManuals.com

EMISSION CONTROL
3
DESCRIPTION AND OPERATION 1.EGR Solenoid
2.Vacuum hose (light brown)
3.T-piece
4.Vacuum hose to brake servo
5.Non-return valve
6.Brake servo
7.Inlet manifold
8.Exhaust manifold
9.EGR pipe
10.Vacuum pump/alternator assembly
11.Air intake hose from intercooler
12.EGR valve assembly
13.Vacuum hose to vacuum pump
14.Vacuum hose to EGR valve suction port (blue)
15.To atmosphere
16.In-line filter
17.Vent hose - EGR solenoid to in-line filter (green)
ProCarManuals.com

EMISSION CONTROL
5
DESCRIPTION AND OPERATION
CAUTION: Inset A shows the Pre-EU3 condition for the EGR pipe. Inset B shows the Pre-EU3
condition filter and venting.
1.ILT valve modulator
2.ILT modulator vacuum hose (brown)
3.EGR valve modulator
4.EGR modulator vacuum hose (brown)
5.Vent hose - EGR modulator to in-line filter (green)
6.Vacuum hose to ILT valve suction port (blue)
7.Vacuum hose to EGR valve suction port (blue)
8.’T’-piece (4-way)
9.Vacuum hose to brake servo
10.Non-return valve
11.Brake servo
12.Inlet manifold
13.Exhaust manifold
14.ILT valve
15.EGR cooler - EU-3 models
16.Vacuum pump/alternator assembly
17.Air intake hose from intercooler
18.EGR valve (incorporating ILT valve) assembly
19.Vacuum hose to vacuum pump
20.Vent hose - ILT valve modulator to in-line filter (green)
21.3-way connector
22.Vent hose to air cleaner
23.ILT modulator harness connector (green)
24.EGR modulator harness connector (black)
25.To atmosphere - Pre-EU3 models
26.In-line filter - Pre-EU3 models
27.EGR pipe - Pre-EU3 models
ProCarManuals.com

17EMISSION CONTROL
10
DESCRIPTION AND OPERATION INLET THROTTLE (ILT) MODULATOR
1.Port to vacuum source (white band)
2.Port to ILT valve (blue band)
3.Port to atmosphere via in-line filter (green band)
4.Harness connector (green)
The ILT modulator is located on a plate fixed to the inner wing on the RH side of the engine below the EGR
modulator. The modulator is attached to the plate by two through-studs, each with two nuts which secure the
modulator assembly to a rubber mounting which helps to reduce noise. The modulator must be mounted in the
vertical orientation with the two vacuum ports uppermost.
The modulator operation is controlled by a signal from the ECM which determines the required ratio of exhaust
gas to fresh inlet air needed in response to inputs relating to air flow and engine operating and ambient conditions.
The modulator has a green two-pin connector at its base to connect it to the ECM through the engine harness.
The ILT valve modulator features three ports:
The top port is identified by a white band and connects to a’T’-piece in the vacuum line via a small-bore brown
plastic hose where it is connected in parallel with the vacuum source line to the EGR valve modulator. The two
other ports on the’T’-piece connect vacuum line hoses of black vinyl tubing between the vacuum pump
attached to the alternator and the brake-servo assembly attached to the bulkhead.
The middle port is identified by a blue band and connects to the suction port on the ILT valve through a
small-bore blue plastic hose.
The lower port is identified by a green band and connects to atmosphere through an in-line filter via a green
plastic hose and a three-way connector positioned in-line between the modulators and the filter. The ILT
modulator hose is connected opposite to the two parallel ports at the three-way connector which connect the
vent lines to the EGR valve modulator and the in-line filter. The other port of the in-line filter vents directly to
atmosphere.
The blue and brown vacuum hoses are protected by corrugated plastic sheaths. The ends of the hoses are fitted
with rubber boots to ensure vacuum tight seals at the component ports.
ProCarManuals.com

30MANIFOLD AND EXHAUST SYSTEM
4
REPAIR
7.Remove 4 bolts securing fuel cooler to inlet
manifold.
8.Remove 2 bolts and remove alternator support
bracket and disconnect fuel injector harness
multiplug.
9.Remove bolt securing engine dip stick tube to
camshaft carrier.
10.Remove dip stick tube and discard’O’ring.
11.Remove 2 nuts and 8 bolts securing inlet
manifold to cylinder head.
12.Disconnect multiplugs from turbocharger boost
control soleniod, ECT sensor, ambient air
pressure sensor, MAF sensor, and A/C
compressor.
NOTE: EU3 Model illustrated.
13.Remove 2 bolts securing harness to camshaft
carrier.
14.Release harness from engine and inlet manifold.
15.Remove inlet manifold and gasket.
ProCarManuals.com

MANIFOLD AND EXHAUST SYSTEM
5
REPAIR Refit
16.Clean inlet manifold and mating face.
17.Fit new gasket.
18.Fit inlet manifold, and working from the centre
outwards, tighten nuts and bolts to25 Nm (18
lbf.ft).
19.Position harness to sensors and connect
multiplugs.
20.Tighten harness clip bolts to camshaft carrier to
10 Nm (7 lbf.ft).
21.Clean dip stick tube and fit new’O’ring.
22.Fit dip stick tube and tighten bolt to10 Nm (7
lbf.ft).
23.Connect glow plug leads.
24.Fit alternator support bracket and tighten bolts to
45 Nm (33 lbf.ft).
25.Position fuel cooler. Apply Loctite 242 to bolts
and tighten to18 Nm (13 lbf.ft).
26.Fit new gasket, position EGR valve and tighten
bolts to9 Nm (7 lbf.ft).
27.Connect multiplug to MAP sensor.
28.Fit cooling fan cowl.
29.Fit engine acoustic cover.
30.Reconnect battery negative lead.
31.Fit battery cover.GASKET - EXHAUST MANIFOLD
Service repair no - 30.15.12
Remove
1.Remove turbocharger.See FUEL SYSTEM,
Repair.
2. Models with A/C:Remove auxiliary drive belt.
See ELECTRICAL, Repair.
3.Remove 4 bolts securing compressor and move
to one side.
All Models
NOTE: EU3 Model illustrated.
4.Remove and discard 2 Allen screws securing
EGR pipe to exhaust manifold.
5.Remove 10 nuts securing exhaust manifold to
cylinder head.
6.Remove exhaust manifold and gasket.
ProCarManuals.com

PANEL REPAIRS
9
REPAIR REAR LAMP PANEL
Remove
1.Disconnect both battery leads, negative lead
first.
2.Disconnect alternator.
3.Remove rear bench seat.
4. RH side:Remove tail door.See CHASSIS
AND BODY, Repair.
5.Remove rear lights and reflector.
6. LH side:Remove number plate and tail door
striker.
Refit
7.Prepare and clean panel joint faces.
8.Reverse removal procedure.REAR CROSSMEMBER PANEL
Remove
1.Disconnect both battery leads, negative lead
first.
2.Remove both rear lamp panels.See this
Section.
Refit
3.Prepare and clean panel joint faces.
4.Reverse removal procedure.
ProCarManuals.com

86 - ELECTRICAL
CONTENTS
Page
DESCRIPTION AND OPERATION
SECURITY AND CENTRAL DOOR LOCKING 1....................................................
SECURITY AND CENTRAL DOOR LOCKING 2....................................................
ANTI-THEFT ALARM - FROM 02MY 3...................................................................
IMMOBILISATION SYSTEM - FROM 02MY 12......................................................
CENTRAL DOOR LOCKING (CDL) - FROM 02MY 15...........................................
ANTI-THEFT ALARM SYSTEM SELF TEST 17.....................................................
FASCIA CONSOLE 18............................................................................................
HEATED FRONT SCREEN - FROM 02MY 20.......................................................
HEATED FRONT SEATS - FROM 02MY 22..........................................................
ELECTRIC FRONT WINDOWS - FROM 02MY 24.................................................
PASSENGER COMPARTMENT FUSE BOX 26.....................................................
UNDER SEAT FUSE BOX 27.................................................................................
ADJUSTMENT
HEADLAMPS - ALIGN BEAM 1..............................................................................
SOLENOID/MOTOR - FRONT DOOR - ADJUST 1................................................
REPAIR
BELT - AUXILLARY DRIVE 1.................................................................................
HARNESS - INJECTORS 1....................................................................................
STARTER MOTOR 2..............................................................................................
CENTRE HIGH MOUNTED STOP LIGHT (CHMSL) - UP TO 02MY 2...................
ALTERNATOR 3.....................................................................................................
HORN - LH 4...........................................................................................................
HEADLAMP 5.........................................................................................................
LAMP - TAIL 6.........................................................................................................
RADIO6 ..................................................................................................................
SPEAKER - FRONT 7.............................................................................................
SWITCH - TRANSMISSION BRAKE 7...................................................................
LAMP - FRONT FLASHER 8..................................................................................
BATTERY - DISCONNECT - FROM 02MY 8..........................................................
MOTOR & REGULATOR - FRONT DOOR - FROM 02MY 9..................................
SWITCH - FASCIA - FROM 02MY 10.....................................................................
HARNESS - FRONT DOOR - FROM 02MY 10.......................................................
SOLENOID/MOTOR - TAIL DOOR - FROM 02MY 11............................................
SOLENOID/MOTOR - FRONT DOOR - FROM 02MY 12.......................................
SOLENOID/MOTOR - REAR DOOR - FROM 02MY 13.........................................
HARNESS - REAR DOOR - FROM 02MY 14.........................................................
REVERSE AND FOG GUARD LAMP - BULB 15....................................................
ProCarManuals.com