1999 JAGUAR S TYPE engine

V6 Engine AJ-V6/AJ28
40
Engine Management Sensors
Key to illustration on page 41:
1. Throttle motor
2. TP sensor
3. IAT sensor
4. MAF sensor
5. Top IMT valve
6. Bottom IMT valve
7. EFT sensor
8. IP sensor
9. Fuel injectors
10. Coil-on-plug units
11. VVT shuttle valve
12. CMP sensor
13. CHT sensor
14. KS sensors
15. EOT sensor
16. CKP sensor
17. HO2 sensors
18. HO2 sensors (catalyst monitors)
Cylinder Head Temperature (CHT) Sensor
The single CHT sensor is located between the two
rear coil-on-plug units in the bank 2 cylinder
head. The sensor directly monitors the metal
temperature of the cylinder head. This method of
engine heat sensing is used in place of a
conventional coolant temperature sensor to
enable the fail safe cooling strategy to operate.
The use of a metal temperature sensor allows
cylinder head temperature to be measured even if
coolant has been lost unlike an ECT sensor which
would produce inaccurate temperature
indications, eg measuring steam temperature.
Crankshaft Position (CKP) Sensor
Crankshaft position and rotational speed are
sensed from a steel timing ring keyed to the front
end of the crankshaft immediately behind the
front cover. The timing ring has 36-1 teeth, ie one
missing tooth, which are angled slightly forward
and bent at rightangles to provide a sensing area
for the inductive sensor. The sensor is positioned
in the front cover, to the side of the crankshaft
damper, at approximately 20û to the plane of the
timing ring.
D.303.1342
J.303.1343
CHT SENSOR
CKP SENSOR
D.303-1342
J.303-1343
Engine management sensors and actuators (but
not off engine sensors) are summarised in the
illustration on page 41 and are also described
below or in the relevant section (VVT, fuel system,
throttle, tuned manifold).
The engine management system is described in a
separate section.

V6 EngineAJ-V6/AJ28
41
J.303.1287
ENGINE MANAGEMENT SCHEMATIC
1
324 5
12
6
8
14
15 7
9
111013
16
J.303-1287
9
1011
12
1214
18 17
1817

V6 Engine AJ-V6/AJ28
42
J.303.1291
KS SENSORS
J.303-1291
Knock (KS) Sensors
Two ÔdonutÕ type knock sensors are fitted, in
assymetrical positions. The bank 2 sensor is
located on top of the block near the oil separator
and the bank 1 sensor is fixed on the RH side of
the block above the starter motor.
D.303.1292
CMP SENSOR
D.303-1292
Camshaft Position (CMP) Sensors
Each inlet camshaft has a four tooth sensor ring
pressed on to the rear end of the camshaft with
the inductive sensor projecting through a hole in
the cylinder head behind and in line with the
sensor ring teeth. The use of a four tooth ring
enables the sensor to provide increased feedback
(position indication of each cylinder).

V6 EngineAJ-V6/AJ28
43 Intake Air Temperature (IAT) Sensor
The IAT sensor is a conventional thermistor type
device which is a push fit in the intake resonator
duct.
Mass Air Flow (MAF) Sensor
The MAF sensor is an integral assembly consisting
of a hot wire sensor unit and air duct and is non-
serviceable. The assembly is fitted between the air
cleaner and intake resonator tube.
D.303.1381
MAF AND IAT SENSORS
D.303-1381
J.303.1386
HO2 SENSORS
J.303-1386
Heated Oxygen (HO2) Sensors
HO2 sensors are fitted in both the upstream and
downstream positions on the catalytic converters.
Both sensors are standard types with a step
response at the stoichiometric (lambda) air/fuel
value. The upstream sensors provide the feedback
for stoichiometric fuelling control and the
downstream sensors monitor catalyst efficiency
and also provide long term fuelling adaptation
trim.
MAF SensorIAT Sensor

V8 EngineAJ-V6/AJ28
45
Introduction
The AJ28 engine is a variant of the 4.0L 90û V8 units fitted to the XJ and XK range of vehicles. The AJ28
shares some of the changes incorporated in the current AJ27 engine: both engines are derived from the
original AJ26 unit. A number of features are unique to the AJ28 or are shared with the AJ-V6 engine also
described in this publication.
Features of the AJ28 engine are:
¥ Continuously variable inlet valve timing over a 48û
+
-2û crank angle: as fitted to the AJ27 engine
¥ Full authority cable-less electronic throttle control: as fitted to the AJ-V6 engine
¥ Air assisted fuel injection: similar to system used on the AJ27 engine
¥ Unique induction manifold with centrally mounted throttle body
¥ Returnless fuel system: similar to AJ-V6 engine
¥ Twin wall exhaust manifold
¥ Engine management system as used on the AJ-V6
¥ New sensors
¥ Modified sump and oil cooler
¥ Modified front end ancillary drive and components
Engine Specification
Maximum power DIN - 209 kW (281 BHP) at 6100 RPM
EEC - 203 kW (276 PS) at 6100 RPM
Maximum torque DIN - 390 Nm (287 lbft) at 4300 RPM
EEC - 278 Nm (279 lbft) at 4300 RPM
Oil Specification
All markets except the USA and Canada
Engine oil for all markets except the USA and
Canada must be to API specification SJ/ACEA A1
or A3.
The recommended SAE viscosity for different
ranges of ambient temperature are shown in
table 1.
USA/Canada
Engine oil for USA and Canada must be to API
specification SJ/ILSAC GF-2.
The recommended SAE viscosity for different
ranges of ambient temperature are shown in
table 2. For maximum economy and in most
climate conditions, SAE 5W/30 is to be preferred
but SAE 10W/30 or 15W/40 are acceptable in
moderate to hot climates.
JOL.29550
50JOL.296
SAE/TEMPERATURE TABLE 2
SAE/TEMPERATURE TABLE 1

V8 Engine AJ-V6/AJ28
46
Basic Engine
Bottom End
Changes to the cylinder block, connecting rods
and pistons which were introduced for the AJ27
N/A engine are also applicable to the AJ28 unit
and are described in the ÔXK and XJ series 1999
MY updateÕ Technical Guide.
Oil Sump Body and Pan
A revised oil sump body and sump pan are
necessary to accommodate the V8 engine in the
S-TYPE model but the sump capacity is
unchanged.
D.303.1184
OIL SUMP AND PAN
D.303-1184
J.303.1317
TRANSMISSION DRIVE PLATE
J.303.1317
Transmission Drive Plate
The transmission drive plate is similar to AJ27 but
is fixed with eight bolts to an adaptor plate on the
torque converter (see Transmission sections). The
crankshaft sensor ring is fitted to the engine side
of the drive plate as for the previous V8 engines.

V8 EngineAJ-V6/AJ28
47
Cylinder Head
The cylinder head incorporates the modifications
first introduced for the AJ27 engine except for the
camshaft sensor ring and cam cover.
Camshaft Sensor Ring
Cam position sensing is similar to that used on the
AJ27 engine, except that the sensor ring fitted to
each inlet camshaft has five triggering teeth.
Camshaft Covers
To improve accessibility, an extension tube is
fitted to the oil filler hole on the bank 2 cam
cover. Due to the position of the throttle and air
intake ducting, the part load breather outlet is
taken from bank 1 cam cover and the full load
breather outlet from bank 2 (the reverse of AJ27).
Front Cover
The front cover is modified from the AJ27 to
include a mounting boss for a new idler pulley
(see Front End Accessories Drive).
Lubrication
The lubrication system includes the uprated oil
pump (for the linear VVT system) and the same oil
temperature sensor as fitted to the AJ27 engine.
The oil sump and pan are modified as described
on page 46.
The external oil system components are located
laterally across the front of the sump body and
consist of an oil filter, oil cooler and oil filter head
assembly. The oil cooler is an oil to water heat
exchanger similar to the V6 oil cooler and the
cooler matrix is also connected via hoses to a
circulator orifice in the radiator bottom hose (see
Cooling System). The oil filter screws on to the
cooler which connects to the sump body through
an adaptor, the oil filter head assembly.
J.303.1189
CAMSHAFT SENSOR RING
D.303.1189
D.303.1185
CAMSHAFT COVER/OIL FILLER
D.303.1185
D.303.1186
OIL FILTER, COOLER AND ADAPTOR
D.303.1185
Oil temperature sensor
Oil pressure switch
Oil Cooler

J.303.1318
V8 Engine AJ-V6/AJ28
48
Exhaust Manifold
The exhaust manifolds have a double wall
construction and are manufactured from
austenitic stainless steel. The double wall
construction has a number of advantages:
¥ it provides a significant reduction in the
external heat generated and therefore
improves underhood thermal management
¥ a heat shield is not required
¥ the durability of the manifold is increased (eg
less likely to crack)
¥ by retaining heat, the insulation effect
provides a slight improvement in the time to
catalyst light-off.
The manifold couples to the catalytic converter
via a spherical joint which requires no gasket or
sealant. EXHAUST MANIFOLD
J.303.1318