1999 FORD ESCORT clock

Replacing headlamp bulbs
1. Make sure that the headlamps are turned OFF.
²Coupe
²Sedan/wagon
2. Open the hood and disconnect the headlamp wiring socket from the
in-line connector. This will make it easier to change the bulb.
3. Remove the protective dust shield
from the housing by turning the
dust shield counterclockwise (when
viewed from the rear).
4. Release clip and disconnect the electrical connector from the bulb.
Maintenance and care
162

5. Remove the bulb retaining ring by
rotating it counterclockwise.
6. Without turning, remove the old
bulb from the lamp assembly by
pulling it straight back out of the
lamp assembly and replace.
7. Install the new bulb in lamp assembly by pushing straight in with the
bulb's plastic base facing upward. Turn the bulb slightly to align the
grooves in the plastic base with the tabs in the lamp assembly.
8. Install the bulb retaining ring over the plastic base and lock the ring
by rotating it clockwise until it snaps into place.
9. Connect the electrical connector into the plastic base until it ªsnapsº.
10. Install the protective dust shield and lock the shield by rotating it
clockwise until it locks into position.
11. Connect the headlamp wiring socket to the in-line connector.
12. Turn the headlamps on and make sure they work properly. If the
headlamp was correctly aligned before you changed the bulb, you should
not need to align it again.
Maintenance and care
163

Replacing foglamp bulbs
1. Remove the bulb socket from the
foglamp by turning
counterclockwise.
2. Disconnect the electrical
connector from the foglamp bulb.
3. Connect the electrical connector
to the new foglamp bulb.
4. Install the bulb socket in the
foglamp turning clockwise.
High-mount brakelamp bulbs
To remove the brakelamp bulb:
1. Push the center of the push pins
in to release tension.
2. Pull the push pins out of the
cover and slide the cover away from
the package tray.
3. Remove the bulb by rotating it
counterclockwise and pulling it out
of the lamp assembly.
4. Carefully pull out the bulb
straight out of the socket and push
in new bulb.
To install the brakelamp bulb:
1. Install the bulb into the lamp assembly and rotate clockwise.
2. Install the push pins in the cover far enough that the pins protrude
outside of the cover about 6mm (1/4 inch).
3. Install the cover and secure with the push pins.
Maintenance and care
164

Tail lamp/Rear turn signal lamp bulbs-Except Wagon
The tail lamp and the turn signal
lamp bulbs are located in the same
portion of the tail lamp assembly,
one just below the other. Follow the
same steps to replace either bulb.
1. Open trunk to expose the tail lamp assembly. Remove the two screws
from the front of the lamp.
2. The tail lamp has hidden fasteners which can be disengaged by hitting
the lamp, with the side of your hand, toward the side of the vehicle.
3. Pull lamp assembly away from vehicle for access to bulbs.
4. Remove the bulb socket by
rotating it counterclockwise, then
pulling it out of the lamp assembly.
5. Pull the bulb from the socket and push in the new bulb.
6. Install the bulb socket into the lamp by rotating it clockwise.
7. Position the tail lamp on the vehicle and gently tap the lens to engage
the clips. Install the screws.
Maintenance and care
165

Tail lamps/Rear turn signal lamp bulbs-Wagon
The tail lamp and the turn signal
bulbs are located in the same
portion of the tail lamp assembly,
one just below the other. Follow the
same steps to replace either bulb.
1. Open liftgate to expose the tail lamp assembly. Remove the three
screws and lamp assembly from the vehicle.
2. Remove the bulb socket by rotating it counterclockwise, then pulling it
out of the lamp assembly.
3. Pull the bulb from the socket and push in the new bulb.
4. Install the bulb socket into the lamp assembly by rotating it clockwise.
5. Install the tail lamp assembly on the vehicle with the three screws.
Maintenance and care
166

Vertical aim adjustment
1. Park the vehicle on a level
surface.
2. With the hood open, locate the
bubble level and the vertical
adjustment screw. The adjustment
screw is located on the outboard
side of the headlamp below the
headlamp upper attachment.
3. The ªUPº and ªDNº on the bubble
indicate the directional change (up
or down) of the vertical aim.
4.Usea4mmwrench or socket to
turn the vertical adjusting screw
clockwise or counterclockwise until
the bubble is centered between the
lines.
Repeat the above process to the other headlamp, if necessary.
CLEANING AND CARING FOR YOUR VEHICLE
Refer to the Customer Assistance chapter for a list of Ford-approved
cleaners, polishes and waxes.
L
R
UP
DN
DNUP
Maintenance and care
169

Air bag supplemental
restraint system ..........................71
and child safety seats ..............73
description ................................71
disposal ......................................75
driver air bag ............................73
indicator light ........................8,75
operation ...................................73
passenger air bag .....................73
Air cleaner filter ................146,174
Air conditioning ..........................37
Anti-theft system ...................58,59
arming the system ....................59
disarming a
triggered system ..................59,60
disarming an untriggered
system .......................................59
warning light ...............................9
Automatic transaxle ...................95
driving with ...............................97
fluid, refill capacities ..............174
fluid, specification ..................176
Battery .......................................144
acid, treating emergencies .....144
charging system
warning light .............................10
jumping a disabled battery ....117
maintenance-free ....................144
replacement, specifications ...174
servicing ..................................144
Brakes ..........................................89
anti-lock ................................89,90
anti-lock brake system
(ABS) warning light ..............9,89
brake warning light ....................8
fluid, checking and adding ....134
fluid, refill capacities ..............174
fluid, specifications ..........175,176
lubricant specifications ...175,176
parking ......................................90
shift interlock ............................95
Break-in period .............................2Capacities for refilling fluids ....174
Cargo cover .................................54
Child safety restraints ................76
child safety belts ......................76
child safety seats ......................77
Child safety seats ........................77
attaching with tether straps ....80
built-in child seat .....................77
in front seat ..............................78
in rear seat ................................78
tether anchorage
hardware ..............................80,81
Cleaning your vehicle ...............169
engine compartment ..............171
exterior ....................................170
exterior lamps .........................172
instrument panel ....................172
interior .....................................173
plastic parts ............................172
safety belts ..............................173
washing ....................................170
waxing .....................................170
wheels ......................................171
wiper blades ............................172
Clock ..................................19,25,33
Clutch
fluid ..........................................135
operation while driving ............92
recommended shift speeds ......94
Coolant ........................137,139,140
checking and adding ..............138
refill capacities .................139,174
specifications ...................175,176
Customer Assistance ................181
Ford accessories
for your vehicle ......................188
Ford Extended
Service Plan ............................182
Getting assistance outside the
U.S. and Canada .....................187
Getting roadside assistance ...181
Index
194