1999 DODGE RAM ad blue

disarm switch state CLOSED, replace CTM.
23) Turn ignition switch to START position. If horn does not
sound, go to next step. If horn sounds, go to step 24).
24) Locate Central Timer Module (CTM). CTM is located behind\
right kick panel. Disconnect CTM 14-pin connector C1. Using an
external voltmeter, measure voltage between ground and CTM 14-pin
connector C1 terminal No. 8 (Dark Blue/White wire). If voltage is more\
than 10 volts, replace CTM. If voltage is 10 volts or less, repair
open Dark Blue/White wire between CTM and RUN-ACC fuse in junction
block.
WINDSHIELD WIPER SYSTEM
WIPER PARK SWITCH FAILURE
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
NOTE: It takes 8 seconds for wiper park switch failure DTC to set.
1) Using scan tool, clear DTCs. See appropriate SELF-
DIAGNOSTICS article. Operate wipers in low speed, then intermittent
mode. Reread DTCs. If WIPER PARK SWITCH FAILURE is displayed, go to
next step. If WIPER PARK SWITCH FAILURE is not displayed, system is
currently functioning properly.
2) Gain access to wiper motor connector. Using an external
voltmeter, measure voltage between ground and wiper motor terminal No.
2 (Dark Green wire). If voltage is more than 9 volts, go to next step.\
If voltage is 9 volts or less, replace wiper motor.
3) Locate Central Timer Module (CTM). CTM is located under
left side of instrument panel. Using an external voltmeter, measure
voltage between ground and backprobe of CTM 14-pin Green connector C1
terminal No. 11 (Dark Green wire). If voltage is 9 volts or less,
replace CTM. If voltage is more than 9 volts, repair short to voltage
in Dark Green wire between CTM and wiper relay or wiper motor.
INTERMITTENT WIPERS INOPERATIVE
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool select CENTRAL TIMER MODULE. If scan tool
displays NO RESPONSE, go to appropriate VEHICLE COMMUNICATIONS
article. If scan tool displays any CCD bus failure message, go to
SYMPTOM IDENTIFICATION. If scan tool does not display NO RESPONSE or
any CCD bus failure message, go to next step.
2) If problem is wipers parking in wrong position, go to next
step. If problem is not wipers parking in wrong position, go to step
5).
3) Gain access to wiper motor connector. Turn wipers on to
low speed. Using an external voltmeter, measure voltage between ground
and wiper motor switch terminal No. 2 (Dark Green wire). If voltage
does not cycle between zero and 12 volts, replace wiper motor. If
voltage cycles between zero and 12 volts, go to next step.

4) Locate Central Timer Module (CTM). CTM is located under
left side of instrument panel. Using an external voltmeter, measure
voltage between ground and backprobe of CTM 14-pin Green connector C1
terminal No. 11 (Dark Green wire). Wipers should be operating at low
speed. If voltage does not cycle between zero and 12 volts, repair
open Dark Green wire between CTM and wiper relay or wiper motor. If
voltage cycles between zero and 10 volts, replace CTM.
5) Using scan tool, monitor intermittent wiper voltage level.
Rotate wiper switch from low intermittent to high intermittent level.
If voltage changes from approximately 2.5 to 12 volts, replace CTM. If
voltage does not change from approximately 2.5 to 12 volts, go to next
step.
6) Disconnect 24-pin multifunction switch connector. Using an
external ohmmeter, measure resistance of White/Dark Blue wire between
multifunction switch connector terminal No. 1 and CTM 14-pin Green
connector C1 terminal No. 12. if resistance is less than 5 ohms,
replace multifunction switch. If resistance is 5 ohms or more, repair
open White/Dark Blue wire between multifunction switch and CTM.
NO WIPER ACTUATION AFTER WASH BUTTON PUSHED
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool select Central Timer Module (CTM). If sca\
n
tool displays NO RESPONSE, go to appropriate VEHICLE COMMUNICATIONS
article. If scan tool displays any CCD bus failure message, go to
SYMPTOM IDENTIFICATION. If scan tool does not display NO RESPONSE or
any CCD bus failure message, go to next step.
2) Turn ignition on. If washer system works, go to next step.
If washer system does not work, see appropriate WIPER/WASHER SYSTEMS
article.
3) Using scan tool, actuate washer. If washer pump sense
displays ON, replace CTM. If washer pump sense does not display ON,
repair open Brown wire between CTM 14-pin connector C1 terminal No. 10
and multifunction switch.
WIPER SPEED SENSITIVE FEATURE INOPERATIVE
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool select Central timer module (CTM). If sca\
n
tool display is not blank or have a CCD bus failure message, go to
next step. If scan tool display is blank or has a CCD bus failure
message, see appropriate VEHICLE COMMUNICATIONS article.
2) Using scan tool, select Powertrain Control Module (PCM).
If scan tool display is not blank or have a CCD bus failure message,
go to next step. If scan tool display is blank or has a CCD bus
failure message, see appropriate VEHICLE COMMUNICATIONS article.
3) Raise and support vehicle. Turn wipers on to lowest
intermittent position. Time interval between wipes. Spin rear wheels
to more than 15 MPH. If interval between wipes decreased to
approximately 18 seconds, system is currently functioning properly. If
interval between wipes did not decrease to approximately 18 seconds,

Fig. 2: Adjusting Transfer Case Shift Linkage (Ram Pickup)
Courtesy of Chrysler Corp.
TROUBLE SHOOTING
NOTE: For trouble shooting not covered in this article, see
appropriate table in TROUBLE SHOOTING article in GENERAL
INFORMATION.
Hydraulic system should not require addition of fluid under
normal circumstances. Reservoir fluid level will increase as normal
clutch wear occurs. Avoid overfilling or removing fluid from
reservoir. This will cause clutch release problems.
TESTING
CLUTCH PEDAL POSITION SWITCH
NOTE: The position switch is an integral part of clutch master
cylinder push rod and cannot be serviced separately.
Disconnect clutch pedal position switch electrical connector.
Depress switch. Using a DVOM, measure continuity between clutch pedal
position switch terminals No. 1 (Yellow/Red wire) and No. 2 (Dark
Blue/Yellow wire). If continuity exists, switch is okay. If continuity
does not exist, replace clutch master cylinder. See CLUTCH MASTER
CYLINDER under REMOVAL & INSTALLATION.

operator's foot off accelerator pedal, S/C compensates for excessive
S/C cable slack. If lift foot sets are continually used, speed control
overshoot/undershoot condition will develop.
To "unlearn" overshoot/undershoot condition, operator must
press and release set button while maintaining desired speed with
accelerator pedal, then turn S/C switch to OFF position after waiting
10 seconds. This procedure must be repeated 10-15 times to completely
unlearn overshoot/undershoot condition.
COMPONENT TESTS
WARNING: Vehicle is equipped with an air bag. Air bag must be
deactivated before servicing speed control components on or
around steering column. See appropriate AIR BAG RESTRAINT
SYSTEMS article.
NOTE: For component locations, See COMPONENT LOCATIONS. For
connector terminal identification, see CONNECTOR
IDENTIFICATION. For wiring diagram, see WIRING DIAGRAMS.
BRAKE SWITCH
Disconnect brake switch 6-pin connector. Using an ohmmeter,
check for continuity at brake switch. See Fig. 1. If continuity is not
as specified in BRAKE SWITCH CONTINUITY table, check brake switch
adjustment. See BRAKE SWITCH under REMOVAL & INSTALLATION. If brake
switch adjustment is okay, replace defective brake switch.
BRAKE SWITCH CONTINUITY








\









\









\









\









\









\









\






 
Switch Plunger  Check Between  Continuity 


Position  Terminals  










\









\

\b







\









\









\


\b







\









\






Released  5 & 6  Yes 










\









\

\b







\









\









\


\b







\









\






Depressed  1 & 2  Yes 











\









\









\
\b








\









\





 3 & 4  Yes 











\









\









\









\









\









\









\





\f

SPEED CONTROL SERVO
1) Start engine. Disconnect Speed Control (S/C) servo 4-pin
connector. Turn S/C on. Using a voltmeter, check voltage at S/C servo
connector terminal No. 3 (Dark Blue/Red wire). Battery voltage should
exist when brake pedal is not depressed. If battery voltage exists, go
to next step. If battery voltage does not exist, check circuit between
brake switch and S/C servo. See WIRING DIAGRAMS.
2) Connect a jumper wire between S/C servo pin No. 3 and S/C
servo connector terminal No. 3. Check voltage at S/C servo pins No. 1,
2 and 4. If battery voltage does not exist, replace S/C servo. If
battery voltage exists, go to next step.
3) Turn ignition off. Check for continuity between S/C servo
connector terminal No. 4 and ground. If continuity exists, test is
complete. If continuity does not exist, repair open ground circuit as
necessary.
VACUUM SUPPLY
Gasoline Engines
1) Disconnect vacuum hose at speed control servo. Install
vacuum gauge to disconnected vacuum hose. Start engine and observe

scan tool displayed P/N and D/R in correct positions, go to next step.
4) Raise drive wheels and support vehicle, allowing wheels to
spin. Using scan tool, erase DTCs. Start engine. Using scan tool, read
Output Speed Sensor (OSS). Shift transmission into first gear. While
observing scan tool, allow wheels to spin at a speed less than 15 MPH.
If scan tool displays OSS more than 60 RPM, go to next step. If scan
tool displays OSS 60 RPM or less, go to step 7).
5) While wheels are spinning, wiggle wiring between OSS and
PCM. If OSS reading dropped while wiggling, repair intermittent short
or open circuit. Perform TEST VER-5A under VERIFICATION TESTS. If OSS
reading did not drop, go to next step.
6) Using scan tool, erase DTCs. Road test vehicle. Read DTCs.
If FTC P0720 returns, replace PCM. Perform TEST VER-5A under
VERIFICATION TESTS. If FTC P0720 did not return, go to step 13).
7) Turn ignition off. Disconnect PCM. Inspect connectors.
Clean or repair as necessary. Using an ohmmeter, measure resistance
between ground and OSS signal circuit at PCM connector C2, terminal
No. 28 (Light Green/Black wire on Ram Pickup; Light Green/White wire
on all other models). If resistance is less than 5 ohms, repair short
to ground. Perform TEST VER-5A under VERIFICATION TESTS.
8) Using an ohmmeter, measure resistance between ground and
OSS ground circuit at PCM connector C2, terminal No. 25 (Dark
Blue/Black wire). If resistance is less than 5 ohms, repair short to
ground. Perform TEST VER-5A under VERIFICATION TESTS. If resistance is
5 ohms or more, go to next step.
9) Disconnect OSS. Using an ohmmeter, measure resistance
across OSS terminals. If resistance is not 300-1200 ohms, replace OSS.
Perform TEST VER-5A under VERIFICATION TESTS. If resistance is 300-
1200 ohms, go to next step.
10) Using an ohmmeter, measure resistance of OSS signal
circuit between PCM connector C2, terminal No. 28 and OSS connector
(Light Green/Black wire on Ram Pickup; Light Green/White wire on all
other models). If resistance is more than 5 ohms, repair open circuit.
Perform TEST VER-5A under VERIFICATION TESTS. If resistance is 5 ohms
or less, go to next step.
11) Using an ohmmeter, measure resistance of OSS ground
circuit between PCM connector C2, terminal No. 25 and OSS connector
(Dark Blue/Black wire). If resistance is more than 5 ohms, repair open\
circuit. Perform TEST VER-5A under VERIFICATION TESTS. If resistance
is 5 ohms or less, go to next step.
12) Reconnect OSS. Using an ohmmeter, measure resistance
between PCM connector C2, terminals No. 25 (Dark Blue/Black wire) and
No. 28 (Light Green/Black wire on Ram Pickup; Light Green/White wire
on all other models). If resistance is 300-1200 ohms, replace PCM.
Perform TEST VER-5A under VERIFICATION TESTS. If resistance is not
300-1200 ohms, go to next step.
13) Inspect wiring and connectors. repair as necessary.
Perform TEST VER-5A under VERIFICATION TESTS. If wiring and connectors
are okay, go to next step.
14) Conditions required to set FTC are not present at this
time. Check freeze frame data to determine conditions when FTC was
set. Raise drive wheels and support vehicle, allowing wheels to spin.
Using scan tool, read OSS. Shift transmission into first gear. While
observing scan tool, allow wheels to spin at a speed less than 15 MPH.
Wiggle wiring between OSS and PCM. If OSS reading dropped while
wiggling, repair intermittent short or open circuit. Perform TEST VER-
5A under VERIFICATION TESTS. If OSS reading did not drop, no problem
is indicated at this time.
FTC P1595: SPEED CONTROL SOLENOID CIRCUITS
Speed Control (S/C) solenoid circuits are monitored when
engine is running, S/C switch is on and battery voltage is more than

10.4 volts. FTC P1595 will set if vacuum and vent solenoids do not
respond when actuated by PCM.
Possible Causes:
* Ground circuit open.
* S/C brake switch output circuit open.
* S/C power supply circuit open or shorted.
* S/C servo defective.
* S/C vacuum solenoid control circuit open or shorted.
* S/C vent solenoid control circuit open or shorted.
* Brake switch defective or out of adjustment.
* Defective PCM.
NOTE: For component locations, see COMPONENT LOCATIONS. For
connector terminal identification, see CONNECTOR
IDENTIFICATION. For wiring diagram, see WIRING DIAGRAMS.
1) Turn ignition on. Turn Speed Control (S/C) on. Using scan\
tool, actuate S/C vent solenoid. If speed control servo clicks, go to
next step. If S/C servo does not click, go to step 7).
2) Using scan tool, actuate S/C vacuum solenoid. If S/C servo
clicks, go to next step. If S/C servo does not click, go to step 6).
3) Turn ignition on. Using scan tool, actuate S/C vacuum
solenoid. Wiggle wiring harness between S/C servo and brake switch to
PCM while scan tool is still actuating speed control vacuum solenoid.
If wiggling did not cause an interruption of S/C servo actuation, go
to next step. If wiggling caused an interruption of S/C servo
actuation, repair wiring harness as necessary. Perform TEST VER-4A
under VERIFICATION TESTS.
4) Turn ignition off. Inspect S/C wiring and connectors.
Clean or repair as necessary. Perform TEST VER-4A under VERIFICATION
TESTS. If wiring and connectors are okay, go to next step.
5) Using scan tool, actuate S/C vent solenoid. Wiggle wiring
harness between S/C servo and brake switch to PCM while scan tool is
still actuating speed control vacuum solenoid. If wiggling did not
cause interruption of S/C servo actuation, test is complete. If
wiggling caused interruption of S/C servo actuation, repair wiring
harness as necessary. Perform TEST VER-4A under VERIFICATION TESTS.
6) Using scan tool, actuate S/C vent solenoid. Wiggle wiring
harness between S/C servo and brake switch to PCM while scan tool is
still actuating speed control vacuum solenoid. If wiggling did not
cause interruption of S/C servo actuation, go to next step. If
wiggling caused interruption of S/C servo actuation, repair wiring
harness as necessary. Perform TEST VER-4A under VERIFICATION TESTS.
NOTE: Ensure brake pedal is not depressed during the following
steps.
7) Turn ignition off. Disconnect S/C servo 4-pin connector.
Inspect all related wiring and connectors and repair as necessary.
Turn ignition on. Turn S/C switch on. Using a 12-volt test light,
probe brake switch output circuit at S/C servo connector terminal No.
3 (Dark Blue/Red wire). If test light is illuminated and bright, go to\
next step. If test light is dim or not illuminated, go to step 13).
8) Turn ignition off. Using an ohmmeter, check resistance of
ground circuit at S/C servo connector terminal No. 4 (Black wire). If
resistance is 5 ohms or more, repair open ground circuit. Perform TEST
VER-4A under VERIFICATION TESTS. If resistance is less than 5 ohms, go
to next step.
9) Disconnect PCM. Inspect connectors. Clean or repair as
necessary. Using an ohmmeter, measure resistance between ground and
S/C vacuum solenoid control circuit at S/C servo connector terminal

No. 1 (Tan/Red wire). If resistance is less than 5 ohms, repair short
to ground. Perform TEST VER-4A under VERIFICATION TESTS. If resistance
is 5 ohms or more, go to next step.
10) Using an ohmmeter, check resistance between ground and
S/C vent solenoid control circuit at S/C servo connector terminal No.
2 (Light Green/Red wire). If resistance is less than 5 ohms, repair
short to ground. Perform TEST VER-4A under VERIFICATION TESTS. If
resistance is 5 ohms or more, go to next step.
11) Using an ohmmeter, measure resistance of S/C vacuum
solenoid control circuit between S/C servo connector terminal No. 1
and PCM connector C3, terminal No. 4 (Tan/Red wire). If resistance is
5 ohms or more, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is less than 5 ohms, go to next
step.
12) Using an ohmmeter, check resistance of S/C vent solenoid
control circuit between S/C servo connector terminal No. 2 and PCM
connector C3, terminal No. 5 (Light Green/Red wire). If resistance is
5 ohms or more, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is less than 5 ohms, replace S/C
servo. Perform TEST VER-4A under VERIFICATION TESTS.
13) Using an ohmmeter, check resistance between ground and
brake switch output circuit at S/C servo connector terminal No. 3
(Dark Blue/Red wire). If resistance is less than 5 ohms, repair short
to ground. Perform TEST VER-4A under VERIFICATION TESTS. If resistance
is 5 ohms or more, go to next step.
14) Reconnect PCM. Disconnect brake switch connector. Turn
ignition on. Turn S/C on. Using a 12-volt test light, probe S/C power
supply circuit at brake switch connector terminal No. 3 (Yellow/Red
wire). If test light is illuminated and bright, go to next step. If
test light is not illuminated or dim, go to step 17).
15) Turn ignition off. Using an ohmmeter, check resistance of
S/C brake switch output circuit between S/C servo connector terminal
No. 3 and brake switch connector terminal No. 4 (Dark Blue/Red wire).
If resistance is 5 ohms or more, repair open circuit. Perform TEST
VER-4A under VERIFICATION TESTS. If resistance is less than 5 ohms, go
to next step.
16) Check brake switch adjustment. See BRAKE SWITCH under
REMOVAL & INSTALLATION. Adjust as necessary. Perform TEST VER- 4A
under VERIFICATION TESTS. If brake switch adjustment is okay, replace
brake switch. Perform TEST VER-4A under VERIFICATION TESTS.
17) Turn ignition off. Disconnect PCM. Inspect connectors.
Clean or repair as necessary. Using an ohmmeter, measure resistance of
S/C power supply circuit between PCM connector C3, terminal No. 11 and
brake switch connector terminal No. 3 (Yellow/Red wire). If resistance\
is 5 ohms or more, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is less than 5 ohms, replace PCM.
Perform TEST VER-4A under VERIFICATION TESTS.
FTC P1596: SPEED CONTROL SWITCH ALWAYS HIGH
FTC P1596 will set if an open circuit is detected in Speed
Control (S/C) switch circuit when ignition is on.
Possible Causes:
* Defective clockspring.
* S/C switch ground circuit open.
* Defective ON/OFF switch.
* Defective PCM.
* S/C switch signal circuit open or shorted to voltage.
NOTE: For component locations, see COMPONENT LOCATIONS. For
connector terminal identification, see CONNECTOR

voltage. If voltage is less than one volt, go to next step. If voltage
is one volt or more, condition to set FTC is not present at this time.
Test is complete.
2) While observing scan tool, disconnect S/C ON/OFF switch.
If S/C switch voltage changes to 5 volts, replace S/C ON/OFF switch.
Perform TEST VER-4A under VERIFICATION TESTS. If voltage does not
change to 5 volts, go to next step.
3) While observing scan tool, disconnect S/C RESUME/ACCEL
switch. If S/C switch voltage changes to 5 volts, replace S/C
RESUME/ACCEL switch. Perform TEST VER-4A under VERIFICATION TESTS. If
voltage does not change to 5 volts, go to next step.
4) Turn ignition off. Ensure both S/C switches are still
disconnected. Using an ohmmeter, check resistance between S/C switch
connector terminals (S/C switch signal circuit and S/C switch ground
circuit). If resistance is less than 5 ohms, repair short circuit.
Perform TEST VER- 4A under VERIFICATION TESTS. If resistance is 5 ohms
or more, go to next step.
5) Disconnect clockspring 4-pin connector. Clockspring 4-pin
connector is located behind steering wheel. Inspect connector. Clean
or repair as necessary. Using an ohmmeter, check resistance between
ground and S/C switch signal circuit at clockspring connector (Dark
Green/Red wire on all models except Ram Van and Ram Wagon; wire color
is not available for Ram Van and Ram Wagon). If resistance is less
than 5 ohms, repair short to ground. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is 5 ohms or more, go to next step.
6) Disconnect PCM. Inspect connectors. Clean or repair as
necessary. Using an ohmmeter, check resistance between ground and S/C
switch signal circuit at either S/C switch connector (Dark Green/Red
wire on all models except Ram Van and Ram Wagon; wire color is not
available for Ram Van and Ram Wagon). If resistance is less than 5
ohms, repair short to ground. Perform TEST VER-4A under VERIFICATION
TESTS. If resistance is 5 ohms or more, replace PCM. Perform TEST VER-
4A under VERIFICATION TESTS.
FTC P1683: SPEED CONTROL POWER RELAY CIRCUIT
FTC P1683 will set if Speed Control (S/C) power supply
circuit is open or shorted when S/C is turned on.
Possible Causes:
* Brake switch out of adjustment.
* S/C brake switch output circuit open or shorted.
* Defective S/C servo.
* Defective brake switch.
* S/C vacuum or vent solenoid control circuits open or
shorted.
* Defective PCM.
* Ground circuit open.
* S/C power supply circuit open.
NOTE: For component locations, see COMPONENT LOCATIONS. For
connector terminal identification, see CONNECTOR
IDENTIFICATION. For wiring diagram, see WIRING DIAGRAMS.
NOTE: Ensure brake pedal is not depressed during the following
steps.
1) Turn ignition off. Disconnect S/C servo connector. Inspect
connector. Clean or repair as necessary. Turn ignition on. Using scan
tool, actuate S/C relay. Using a 12-volt test light, probe S/C brake
switch output circuit at S/C servo connector terminal No. 3 (Dark
Blue/Red wire). If test light is illuminated and bright, go to next